How to attach metal roofing roof: advice from the masters

Date:

2018-04-02 01:12:22

Views:

521

Rating:

1Like 0Dislike

Share:

Table of contents:

Metal in our time has become a recognized leader among roofing materials. It is reliable, durable and aesthetic solution. Quite often the installation trust the professionals, but if you plan to do the installation yourself, be thoroughly acquainted with the technology of its holding.

Why choose metal roofing

If you still have not decided which roofing material to choose for your roof, you should take a closer look with the advantages of metal.

how to attach metal roofing on the roof

This material displaces all the others (for example, slate, wood), because it has such advantages:

  • Low weight;
  • Wide choice of colors;
  • High durability.

In addition, this material is quite easy to mount, it is not repairable and has no harmful components in the composition. The leaves possess high durability which is achieved due to the presence of ribs. Additional important quality - the material is resistant to jumps in temperature, plus, it has a minimal thermal expansion.

Preparing materials and tools

If you pondered the question about how to fasten metal roofing to the roof, you have to make sure you have all the tools.

how to attach metal roofing to the roof with screws

Always, it is important that every detail was at hand, especially when working on the roof. Here is a list of what you need to prepare:

  • Tin snips;
  • Screwdriver;
  • The token.
  • Measuring tool;
  • Drill
  • Safety goggles;
  • Hammer;
  • Long rail;
  • Mounting tape;
  • Gloves.

Metal Shears, you can replace the electric clippers. With regard to the materials in the collection are:

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

  • Metal;
  • Ridge and end plate;
  • Guiding Board;
  • Decorative moldings;
  • Waterproof material.

In Addition, you also need roofing straps, and screws, which should have sealing washers. Additionally, care should be taken about the availability of trim boards, its section must be equal to 100 x 25 mm. Should buy more and aerosolic.

How to deal with sheets of metal

Before you mount the metal roofing on the roof, you should be familiar with the rules for the treatment of these covering materials. Despite the fact that metal is a pretty solid solution, works with her participation requires the observance of some rules. For example, the sheets should be handled only by the edge of the stamping line, but you must act in gloves.

metal roof installationTo Raise the leaves upward from the rails of the boards. When you move to cover the roof it is necessary to show attention. Shoes must be soft-soled. On the crest of a wave attack is strictly forbidden, the leg must put to the toe, and the foot should be directed parallel to the slope, it will have to be in the same groove.

Cut out the leaves grinder, is impossible, as when using a polymeric protective coating may be damaged. For cutting it is recommended to use metal scissors. Best suited electric scissors, because they are easy to work on the ground and the roof. It is important to remember personal safety: you must work in protective glasses and gloves.

Technology installation

Before you mount the metal roofing on the roof, you should be familiar with the nuances of installation. Board crates stuffed with the step equal to the width of the sheets. Standard size of used screws equal to 4 mm. 8х28 to Choose the necessary mounting hardware and even the color matching the color of the roof.

Assembly box roof from metal roofing

Together with the screws use rubber gasket. The fastener twists in the regular places, they are located between the crests of the waves, to derogate from stamping line is 15 mm. tighten the Screws perpendicular to the boards of the system frame, while the strip is a little compressed.

The Algorithm of management works

Answering the question of how to fasten metal roofing on the roof, it is necessary to warn that the leaves are joined on the waves to protect the coating from side winds. Docking is carried out with screws that are screwed into the crest of a wave cloth near the top. First it is good to tighten the longitudinal joints. The sheets are joined in rows. Docking is on the Board of the sheathing. It is important to ensure the fastening of each wave.

The Installation of the material on the cornice can be done in two ways. The first involves runoff from the leaf in the gutter. It is necessary to make a projection in the cornice 5 cm the Board of the cornice should be thicker than the frame boards 15 mm.

technology fastening of metal roof

If the sheathing you plan to use a 100-mm boards, the first should be installed with the retreat of 250 mm from the eaves. 70 mm above from the stamping line are regular places of fastening. If the roof has a stepped cornice or the roof geometry is violated, then the installation of the sheets is the second method.The water will first fall on the curtain bar, and then in the gutter system.

Board sheathing, located on the edge, would the top it is a support ridge Board. To ensure the gap it should be thicker than 15 mm compared with the boards of the crates. Before you mount a horse on the roof of metal, you should make sure that the bar is attracted to the surface of the covering material with screws. They are installed in the crest of a wave, to move away from each other have 80 cm To the front Board fixed end of the strap, the consumption of the screws will be approximately 9 pieces per square meter.

Installing metal roofing on a rectangular pitch of the roof

You will be sure to study carefully step-by-step photos on how to fasten metal roofing to the roof with screws. Visual images help to understand this process. When installing material in a rectangular ramp you need to build a crate. To do this, use edged Board, the size of which will be 100х25 mm.

technology fastening of metal roof

The First set cornice boards, you need to display it horizontally. Any deviation from it is necessary to fix the first Board sheathing. The distance between these elements will be 250 mm. All subsequent boards are installed at a distance of 350 mm. laid every five rows is checked, and the step of sheathing.

The bar set Curtain hooks cornice boards. Laying of metal is necessary to implement with high accuracy. If you make a mistake when assembling the cornice Board, then unfortunately, you will have the whole crate to redo. The laying of the covering material can be carried out from left to right or Vice versa. If you decided to act right, then each successive sheet will have to apply to the previous one. When installing from left to right, the cloth slips under the previous one.

For the correct stretch necessary to take them through two rows, and then fix the docking range. Four sheets are joined together under the existing rules. First joining two sheets along the rows, and after them joined two of the next sheet. There is another option of installation, which requires the attachment on the waves. After that, the sheets are joined top of the canvas. In the place where United together four sheet is thickening. In order to remove it, should the capillary groove is located below the stamping line to straighten. Sometimes masters just cut off part of the corner.

Setting up of separate elements

Studying how to strengthen a metal roof, you need to consider the features of the installation of the individual elements. At the same end of the strap is fixed with an overlap of 2 cm, However, can act also on the flange. The size of the wave tile sheets are adjusted to the width of the slope to the pediment do not bear the crest of a wave.

attaching the metal roof

The Overhang of the gable should be adjusted, but you can just add a roof bar. Between it and the sheet fit seal. Attachment of metal roof is accompanied by the installation of the Windows (attic and/or auditory), plus pipes, which may be located below the ridge. To do this, use a single-leaf, who spent two for each element.

Before installing the planks of the skate should carry out ventilation under the roof. If the roof has steep slopes between the ridge lath and paintings covering material should be placed aerosolic, which eliminates the ingress of snow under the horse.

The Installation of the skate is on the end of the strap, thus it is necessary to provide the protruding edge 30 mm. If you have a flat skate, then details are recorded with an overlap. If you are using a semicircular ridge, then fixed it on the profile line. When the roof has a slope angle of more than 45 °, in advance you will need to determine, does the angle of the model trims of the ridge.

Metal roofing on trapezoidal and triangular rays

The Technology of fastening of the metal roof may involve carrying out works in the case of triangular or trapezoidal ramps. These works are accompanied by the installation of additional bars. They are installed on both sides of the ridge should be directed along the crest line of the roof.

You can Then start the installation of cornice boards and sheathing. In the next phase constructed a system of eaves. Metal must be dimensioned from the centerline. The lower blade is aligned with the position of the cornice Board. Between the cut sheets distance to be 10 cm roof Installation of metal roofing involves the installation of the ridge components. Here it is necessary to act in a certain sequence.

Direct the horse you want to trim in accordance with the corners, and the plastic plug must be installed for semi-circular ridge. The axis of the ridge of the strap coincides with the axis of the ridge. If neighboring rays have equal angles, then follow this will be easy. If the angles are different, the contiguity rays will provide more difficult. Control their position using mounting tape.

Construction of the valley

Assembly box roof of metal involves the construction of a valley. It should be an additional Board. Valley straps are mounted from the bottom up, whenit is necessary to provide overlap along the 30 cm bottom bracket of this node should be cut off below the eaves line, it should flare. Under the flare of the valley and ridge need to install the seal. In this case, the gap in the range of 10 mm or more is required to provide two sides between the cloth covering material and the centerline of the valley.self tapping metal

Learning how to fasten metal roofing to the roof with screws, you should know that the fastener is installed with a deviation of 1.5 cm from the stamping line, if the sheet is circumcised. If the roof structure was assembled correctly, in the place where the sheet is fixed, it will touch the Board is located on the valley. When the master makes a mistake, and mounting of the sheet is carried out at other points in the roof remain gaps where the later design flows. That's a pretty significant disadvantage, so to deviate from the recommendations on installation impossible.

Installing decorative overlays

In order to cover up the cut fabric, use a decorative moulding. Installation is carried out from bottom to top and overlap should be 10 cm or more. If you, like many other home masters asked a question about how to fasten metal roofing to the roof with screws, you should know that between the lining and covering material the gasket is not installed.

When installing a decorative element, it is important to ensure that the screws will not hurt the valley sheet straps. Quite often the design has valleys that start and end on the ramp. This is true in the construction of a Dormer window. This requires additional Board that is placed under the valley. The canvas covering material should be cut so that the cutting level was above the outlet of the valley to the slope 20 cm Under the side and front walls of the window you should make a cutout in the metal. On the canvas fit seal along the walls of the window and the eaves will need to close the placket.

One important caveat: strengthening metal roofing screw, you should take care of the installation of a valley, which is cut off on the ledge and ramp.

Conclusion

The Sheets of metal are modern and very durable roofing material. If you correctly carry out the installation, the coating will be ready to serve up to 50 years and more. However, before you can begin to learn how to fasten metal roofing to the roof with screws, you have to remember that this material is not used for the device flat roofs. They have a minimal slope that does not exceed 2 gr., and the manufacturer recommends that you use a metal roofing on the roofs, the slope of which exceeds 11 grams.

If you can not boast of great experience in such work, we recommend you to prepare thoroughly and study the technology. They suggest the need to purchase the entire set of tools and materials. In particular, do not skimp on good-quality items.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/10303-yak-macavac-metaladaho-ku-na-dahu-parady-maystro.html

DE: https://tostpost.com/de/gem-tlichkeit/10305-metalld-cher-anbringen-auf-dem-dach-tipps-meister.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/10310-c-mo-se-instalan-las-metallocherepicu-en-la-azotea-los-consejos-de-los.html

KK: https://tostpost.com/kk/domashniy-uyut/10306-ret-nde-suge-metall-shatyr-t-bes-nde-ke-ester-sheberler.html

PL: https://tostpost.com/pl/komfort-domu/10306-jak-mocowa-na-dachu-blachodach-wk-porady-mistrz-w.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/10302-como-montar-metallocherepicu-no-telhado-dicas-de-mestres.html

TR: https://tostpost.com/tr/domashniy-uyut/10310-olarak-g-lendirmek-i-in-metal-at-kaplama-at-ipu-lar-ustalar.html

UK: https://tostpost.com/uk/domashn-y-zatishok/10305-yak-kr-piti-metalocherepicyu-na-dahu-poradi-maystr-v.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Achieve The Tefal. Pan product of high technology

Achieve The Tefal. Pan product of high technology

Cooking in France is considered high art. French industrial design has a long tradition and is appreciated by professionals and ordinary consumers. Together, these factors led to the emergence of dishes and kitchen equipment of th...

How to grow strawberries from seeds: tips for beginners gardeners

How to grow strawberries from seeds: tips for beginners gardeners

Growing strawberries from seed is currently gaining popularity. Doing so is fairly easy, but to observe the process of vegetation – exciting.Choose the right variety and planting timeHow to grow strawberries from seeds?...

Cucumber Ecole novice semenovodstva

Cucumber Ecole novice semenovodstva

Home to the popular worldwide plants is India. The cucumber – this is one of the crops grown since ancient times, it is about 3000 years old. Warm and balanced watering are important factors for obtaining high yields.a novel...

Voltage indicators - instruments to guard the safety of people

Voltage indicators - instruments to guard the safety of people

voltage indicators represent portable devices that serve to establish the presence or absence of voltage at various current-carrying parts of mechanisms and machines, as well as the elements of the electrical network.the Carrying ...

The housekeeper wall with their hands

The housekeeper wall with their hands

How often, leaving home, standing on the doorstep, you suddenly realized that the keys of the apartment, country house or garage in the zone of visibility is not observed? They are not anywhere else - not in pockets or on the tabl...

Salt and vinegar against weeds: the recipe, the proportions, reviews

Salt and vinegar against weeds: the recipe, the proportions, reviews

there is No such garden, which would not grow weeds. To deal with them is quite difficult, and it is time-consuming and tedious process. The weeds are ubiquitous and perfectly adapt to any conditions. If the time to get rid of the...