How to build a frame garage of profile pipes with their hands: drawings, photos

Date:

2019-06-29 03:20:23

Views:

618

Rating:

1Like 0Dislike

Share:

Table of contents:

The Garage of profile pipes with their hands can build in a short time. Today this design is the most popular. Inside you can arrange a viewing hole, for which apply concrete blocks. The base can be created in the form of tape construction as the garage has a low weight. Floor easier to run with a tie strap made of water repellent concrete. After Assembly of the walls of the shaped tube can be sheathed on two sides of the profiled steel sheets. Their use is convenient for those that received between them the space to lay insulation. For this you may use stone wool or mineral of its kind, polyurethane foam and polystyrene plates.

Building the Foundation

garage of profile pipes with their hands

If you decide to build a garage of profile pipes with your hands, you should start with marking the territory. On the prepared site will be built low-depth foundations, the width of the ribbon which will be the limit from 20 to 30 centimeters. Its height should be equal to about 40 centimeters. Initially, you need to cut the soil to a depth of 0.5 meters. The area must be carefully aligned and covered with sand, which after you have compacted, watering with water.

The hole you need to prepare your pit, you need to produce work so that the width of the prepared hole was larger than the width of the end of an inspection pit. The perimeter needs to be a gap in the meter. His bottom is filled with sand and RAM by the above procedure. If the site high groundwater flow around the inspection pits running drainage pipes are deduced in a natural pond, instead of which can be the sewage system.

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Building a garage of profile pipes with your hands, you need to make a layout of the Foundation around the perimeter of the building. The walls of the inspection pits should be marked with pegs and cord. Strip foundations should be performed using concrete blocks, laying of which is on a cement-sandy solution. The walls of the pit are made from brick or blocks. After solidification of the solution, you can perform the waterproofing of the walls of the pit from the external side using a rolled material or a mastic made of bitumen. And then the wizard will backfill with sand.

Floor laying

timber frame garage of profile pipes with their hands

Flooring can be made of concrete, that the soil is leveled, after filled with sand to the level of 10 cm below the walls of the pit. On the perimeter of the floor to the walls to strengthen the special damping tape that is required to eliminate the deformation of the material when the temperature changes. The sand is rammed, it fit insulation, so that she went to the basement wall by 15 inches. As a waterproofing you can use roofing felt, roll material or a solid film.

If you'll build the garage of profile pipes with your hands, then have to lay reinforcing mesh in increments of 15 centimeters, then we should start pouring concrete screed. Its surface is levelled with a rule. The ingredients of the concrete mix it is possible to add modifying substances to increase gidrostroitely and plasticity. This can be attributed to the mixture penetrating waterproofing, polymer filler or liquid glass. The floor surface must be dry within 3 weeks, in this period it is not necessary to load the base.

Construction frame

frame garage of profile pipes with their hands

For work it is necessary to prepare a pair of tin snips, screws, a screwdriver, a tape measure. Quite often, home masters today are performing frame garage of profile pipes with their hands. The elements are fastened with screws. However, the original material cut to size, and then placed on a flat surface. This will create the side wall, strengthening of the workpiece between them. Vertical posts must be oriented in such a way that between them was a distance equal to the width of the sheet metal profile. Then between the pillars are three stands, the distance between them should be approximately 50 centimeters. In order to perform perpendicular if the angles need to compare the diagonal of the frame. The same technology to collect the second side wall.

Technique works

garage of profile pipes with your hands drawings

The walls of the frame will have a specific form, which depends on the roof. If it is planar, the rear wall must be performed in the form of a rectangle. For the arrangement of a gable roof to a rectangular wall is strengthened by a pediment. When made frame garage of profile pipes with your hands, the front wall need to perform two pieces, one of them will have a rectangular frame for a gate, while the other will be the pediment.

Rack frame amplified with the use of the pipe. The woodwork is made of the same elements that underlie the garage. They should be rectangles of the same size, pull them together on the diagonal must be with the ribs.The frame originally going on the finished Foundation, wall fastened together with screws. Addition to fix you corners, dowel-nails or screws. Once the grout hardens, you can begin waterproofing the walls of the inspection pits on the outside. You then complete the backfilling.

Construction

garage of profile pipes with their hands photo

The Garage of profile pipes with his own hands with a pent roof runs on a particular technology. In the next phase it involves the arrangement of the roofing system. You can use the I-beam whose thickness corresponds to the thickness of the walls. For rafters you can use 70-centimeter bars, filling the void between the material that underlies the garage box. Mauerlat rigidly fixed to the wall, it should use anchors. Before you are installed the retaining beams, and otherwise – the rafters, the working surface is aligned and protected from moisture. For this you can use roofing felt.

After the belt is arranged on the beams marked the place of occurrence of the rafters, then cut the slot for installation. The grooves are processed by means of protection, and after the rafters are placed into the prepared socket, the ends protruding over the limit mauerlat to 40 centimeters. Mounting elements to the beam is done with anchor bolts and straps that are twisted for strength of copper wire.

Reference

garage of profile pipes with their hands with pent roof

If built, the garage of profile pipes with their hands under the KAMAZ, the methodology of the work remains the same, but the length of the retaining beams may be longer than 4.5 meters. It will need helpers. The sheathing for installation of the roof will need to fill out the thin bars of which are perpendicular relative to the supporting structure, on top of the membrane. Depending on how heavy roofing material, you will need to determine the pitch arrangement of crates.

Paneling

garage of profile pipes with their hands under KAMAZ

If you will be garage of profile pipes with his own hands, photos of such buildings it is recommended to consider in advance. This will allow you to avoid mistakes. For insulation you need to choose the material the desired thickness, which is typically the limit from 5 to 10 centimeters. On the rack should be secured to the cross rails, and then you can proceed to the installation of insulation in the spaces between the uprights. On top of a heater should be fixed parallelization film. The decoration is made of metal profiled sheets, which are fixed with screws.

Conclusion

If you will be a garage of profile pipes with his own hands the drawings in the article, it is recommended to consider. They will understand that this technology can be traced quite easy garage of corrugated Board without insulation and an inspection pit. It will cost much cheaper.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/29323-yak-pabudavac-karkasny-garazh-z-prof-l-nay-truby-sva-m-rukam-charcyazh.html

DE: https://tostpost.com/de/gem-tlichkeit/29355-wie-bauen-skeleton-garage-aus-formrohr-mit-ihren-h-nden-zeichnungen-fo.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/29381-como-construir-esquel-tica-garaje-del-perfil-de-la-tuber-a-con-sus-man.html

KK: https://tostpost.com/kk/domashniy-uyut/29288-alay-soorudit-karkasnyy-garazh-profil-d-byrdan-zhasal-an-z-oldarymen-s.html

PL: https://tostpost.com/pl/komfort-domu/29167-jak-zbudowa-drewniany-gara-z-profili-stalowych-w-asnymi-r-kami-rysunki.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/29198-como-construir-o-quadro-garagem-do-perfil-da-tubula-o-com-suas-pr-pria.html

TR: https://tostpost.com/tr/domashniy-uyut/31461-nas-l-olu-turmak-i-in-iskelet-garaj-d-nda-profil-boru-elleriyle-izimle.html

UK: https://tostpost.com/uk/domashn-y-zatishok/29268-yak-sporuditi-karkasniy-garazh-z-prof-l-no-trubi-svo-mi-rukami-kreslen.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Air conditioning: schematic and working principle

Air conditioning: schematic and working principle

Despite the fact that there are conditioners in almost every house, only a few users correctly identify the diagram of such a device and how it works, connects. This article will try deployed to cover it.General scheme of operatio...

Imperata cylindrical

Imperata cylindrical "Red Baron": planting, care and reviews

the flora of our planet of diversity, and all owners of country houses are enthusiastic about using her gifts to decorate their plots okolonosovyh territories. Thus to create your own perfect area in which to spend time, to enjoy ...

Cloud's breath - planting and care

Cloud's breath - planting and care

Ease and grace gives a bouquet the presence of baby's breath. a Little floating in the air, the flowers form fluffy as white clouds, star-shaped inflorescence. It is a tender plant, lovely, like a breath of wind in the hottest hou...

Julienne Uralochka: description, planting and care

Julienne Uralochka: description, planting and care

Pear in the Urals – a rare phenomenon. Until recently the gardens had met, as a rule, only the northerner. In recent years the situation has changed in connection with the development laboratory of plant breeding, which offe...

DIY tyre Playground in your own hands

DIY tyre Playground in your own hands

an Important element of landscape design is a Playground. There are plenty of great ideas to build the perfect recreation area for the crumbs. One of them – is to create an amazing Playground from old tires. You need to exer...

Modern living room: pictures. Living room design in modern style

Modern living room: pictures. Living room design in modern style

Everyone strives to make your home attractive and cozy. Depends on the atmosphere of the home, the psychological condition of people. Special attention deserves a living – business card of every home. It is in this room the ...