Welding inverter "Svarog ARC 205": description, specifications, price, reviews

Date:

2020-04-02 13:20:17

Views:

519

Rating:

1Like 0Dislike

Share:

Table of contents:

Among the welding inverter deserve particular attention inexpensive but reliable and undemanding machines. Among them are the device "Svarog ARC 205" from the welding units of the same name. Products are manufactured in China. Svarog arc 205

Advantages and disadvantages

Like many other inverters, the line "Svarog" has the following advantages:

  • Due to the ease of ignition and stable arc, which samoreguliruetsja, the welding process is easily mastered even by a beginner;
  • Produced little spray and metal is well boiled;
  • High efficiency – 85 %;
  • Small open-circuit voltage while the inverter is just 9-15 In recovery to 65 In the touch electrode surface;
  • The device is protected from overheating, and also in the scheme kompensiruet drop the mains voltage.

Among the shortcomings should be noted the susceptibility to moisture. In the rain welding is better not to produce or should reliably protect the device from splash. The presence of dust inside the inverters affects their health. Particularly adversely affected by contamination from cutting or grinding metal. Apparatus should be periodically cleaned by blowing compressed air, preventing the accumulation of dust inside.

Specifications

Inverter "Svarog ARC 205" is used in everyday life, but it common to see professionals in the construction, automobile repair, etc.

  1. Power welding current adjustable in the range of 10-180 A. Typically, the number on the label describes its maximum value, but some devices of this type are not affected.
  2. Duration (PN) is 60% when the thickness of the electrode of 4 mm. If you take the electrode is 3 mm, then install the current 120-130 And cooking can be continuously (PN = 100 %).
  3. Allowable voltage range power – 187-253 V. the Device works reliably in rural and suburban areas, where the quality of the network is lower than in the city.
  4. Weight – at 5.8 kg. With the machine can be moved around the job site with a shoulder strap.
  5. Welding Modes – coated electrode (MMA) and TIG (TIG - if there are conditions of connection to the apparatus the valve of the burner and the tank of argon). Manual welding is done with either polarity. Amperage is adjusted stepless. It's not always convenient, because when you accidentally touch the setting can be off. Possible end-to-end penetration of metal not thicker than 3 mm.
  6. Diameter of the electrodes can vary from 1.6 to 4 mm. At high currents the wiring needs to match the power, and the machine applies a current of at least 16A.

Welding inverter "Svarog ARC 205": price

For the price of its class the device may seem expensive, but one that is justified by high functionality and good performance.welding inverter arc Svarog 205 price

Recommended

Staff evaluation: system and methods

Staff evaluation: system and methods

Personnel Assessment allows you to identify how competent the employees involved in the enterprise, and it is the performance of their work – the most significant factor affecting the efficiency of the company. To clarify the impact of performa...

How to start your own business: important aspects.

How to start your own business: important aspects.

Many people, tired of working for someone else, are increasingly thinking about how to start your own business. Someone wants to open a salon, someone store, and someone enough and vegetable stalls. Before you throw in the pool with his head, it is i...

business activities. its essence and basic functions

Business activities. its essence and basic functions

The Entrepreneurial activity of the citizen – is undertaken at your own risk and independent activity, which aims to systematically profit through the sale of works, goods, services, use of the property. The citizen engaged in such activities, ...

How much for a welding inverter "Svarog “ARC 205"? The price is about 14 thousand rubles. When buying you should pay attention to the characteristics. For example, "Svarog TECH ARC 205 B" (Z203) designed for maximum welding current 200 A (power – 9 kVA), and "SwarG ARC 205" (J96) – 180 A. If the first welding electrode to 5 mm, the second fits up to 4 mm.Svarog arc j96 205

Inverter with display

Model is worth 2 thousand rubles. more expensive. The model is made in modern style, small size, has high reliability. A built-in fan to prevent overheating of the apparatus. The device is easy to apply in the private sector, in small workshops and on construction sites.

Description of unit

The High reliability of the welding inverter is provided through the use of IGBT modules manufactured by the German concern Siemens and is designed to operate in adverse conditions.

The functionality of the apparatus is not particularly stands out among the others. It uses the following functions.

  1. Hot start – the sharp increase in current when you touch the electrode metal. Here it is not sticky, which is typical for conventional welding transformers. This is especially noticeable in the process of welding layers of rust or at reduced voltage.
  2. ArcForce – a handy feature in case of accidental extinguishing of the arc. Here also occurs the impingement of the current.
  3. Antistick – in case of sticking of the electrode voltage drops to zero, which prevents a short circuit. The electrode can detach from the details and again to continue the welding process.

How to work with inverter machine "Svarog"?

The Durability and reliability of the inverter depends on its proper operation. The apparatus is set in such a manner that it is ensured a sufficient air flow for ventilation, to keep dust, dirt, sparks of metal and had operated in aggressive environment.

When connecting to the network inverter "Svarog ARC 205" should verify its compliance with the characteristics given on the plate attached to the body. Circuit breaker and socket should be in power to the standard plug of the apparatus. When working at the points of contact should not be arcing and overheating. The device can be used for argon welding.inverter Svarog arc 205

For manual arc welding select MMA mode using the switch on the panel.

Forward and reverse cables are firmly inserted in the panelconnectors “+” and “-”. Then tips to turn clockwise. When welding with straight polarity elektrodvigatel plugs into “-” and return – to “+”.

Excessively long welding cables should be avoided. To prevent a large voltage drop, wire length should be taken with enlarged cross section.

The Welding current is set by the control knob of the same name. It needs to match the diameter of the electrode.

Under normal operation, special maintenance welding inverter is not required. Special attention is paid to the reliability of the connectors and no damage on power cables, housing and management authorities.

Frequent failures and Troubleshooting

For the welding inverter "Svarog ARC 205" typical problems inherent in all such models.

  1. Disable protection due to overheating. The reason may be the dusting apparatus. The inverter should be periodically or selectively clear with compressed air. Dust accumulates with regular use on outdoor construction sites. In case of failure of thermostat, it is a false positive, although the unit does not overheat. The part should be replaced in the service. The connections can be bad contacts that need to be tightened.
  2. Permanent sticking of the electrode at the arc and with proper apparatus arise in the drop of voltage below normal, or when using a weak power wire.
  3. Burnout of the apparatus with the smell of burning insulation is the result of a short circuit. The repair is carried out in specialized workshops. Burnt wires can be replaced independently.

welding machine arc Svarog 205

Annual service unit in the service center allows you to operate it much longer warranty period of 5 years. From different manufacturers it can differ and be not more than 2 years, although it is not so little.

Inverter "Svarog ARC 205": reviews

According to users, the apparatus does not overheat with proper maintenance. Unlike other products, "Svarog ARC 205" works stably at ambient temperature up to +40°C.inverter Svarog arc 205 reviews

There is wide mains voltage range, which allows to apply the device in the country. Stable arc is maintained at a voltage of 160 V. the device Especially like the newcomers, helping them in the work at the initial stage of learning. Experienced welders note the convenient package of the device within the suitcase, where the apparatus is placed a flap, the cables and grip.

When working in wet weather it is recommended to protect the welder "Svarog ARC 205" from splash.welding inverter arc Svarog 205

In frosty weather can be cooked at a temperature below - 10°C, because then the electronics can not withstand.

The company confirms the high efficiency of the device, giving him a long-term warranty.

Conclusion

Device "Svarog ARC 205" for the most part intended for professional use for large volumes of work in the home. For periodic applications from time to time you can buy the car cheaper and simpler, with fewer functions.


Article in other languages:

AR: https://tostpost.com/ar/business/21732-svarog-205.html

BE: https://tostpost.com/be/b-znes/39246-zvarachny-nvertar-svarog-arc-205-ap-sanne-tehn-chnyya-haraktarystyk-ce.html

DE: https://tostpost.com/de/business/38756-inverter-schwei-ger-t-svarog-arc-205-beschreibung-technische-daten-pre.html

ES: https://tostpost.com/es/centro-de/38522-soldadura-inverter-svarog-arc-205-descripci-n-caracter-sticas-t-cnicas.html

HI: https://tostpost.com/hi/business/23304-svarog-205.html

JA: https://tostpost.com/ja/business/21310-svarog-205.html

KK: https://tostpost.com/kk/biznes/39617-svarochnyy-invertor-svarog-arc-205-sipattamasy-tehnikaly-sipattamalary.html

PL: https://tostpost.com/pl/biznes/41323-spawarka-inverter-swar-g-arc-205-opis-dane-techniczne-ceny-opinie.html

PT: https://tostpost.com/pt/neg-cios/40982-de-welding-do-inversor-svarog-arc-205-descri-o-especifica-es-pre-os-co.html

TR: https://tostpost.com/tr/business/36148-kaynak-inverter-svarog-arc-205-tan-m-zellikleri-fiyatlar-yorumlar.html

UK: https://tostpost.com/uk/b-znes/40073-zvaryuval-niy-nvertor-svarog-arc-205-opis-tehn-chn-harakteristiki-c-ni.html

ZH: https://tostpost.com/zh/business/36262-205.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Antifriction materials: overview of properties, application

Antifriction materials: overview of properties, application

the Process of maintenance of technical plant, machinery and separate elemental groups of equipment is inevitably accompanied by wear. The mutual mechanical action of parts on each other with varying degrees of intensity leads to ...

Manufacturing business: ideas, examples

Manufacturing business: ideas, examples

If you have decided to start their own business and production plan business process, that is going to produce some goods, you should know what to navigate. The determining factor in these cases was and remains the existence of co...

OOO

OOO "Savelovsky machine-building factory": the history, products

OOO «Savelovsky engineering plant” is one of the largest enterprises of the Russian machine tool industry. Joint-stock company specializiruetsya in the production of high-tech machines, equipment for the nuclear and ae...

Accounting document: types, form, pattern and design

Accounting document: types, form, pattern and design

Proper documentation is important for any business because it allows you to competently engage in the main activity and not to be afraid of tax and other inspections. Reporting documents are prepared in a variety of types and form...

"Gazelkin": the feedback from the drivers about the job company description

Moving is an event extremely difficult. Transport large quantities of heavy and bulky items alone is not possible. Somehow have to use the services of carriers. How to choose the right company? Or, maybe go to private carriers?Exp...

Chinese incubator automatic: manual, reviews

Chinese incubator automatic: manual, reviews

China — an agrarian country. Therefore, different kinds of goods intended for livestock, it also produces a lot. Of course, supply the Russian market manufacturers and China automatic incubators. Domestic farmers Chinese pro...