Cutting metal in the home and in industrial scale

Date:

2020-06-18 16:00:09

Views:

476

Rating:

1Like 0Dislike

Share:

Table of contents:

Very often necessary in cutting apart large sheets of metal, breaking off pieces from them, cutting grooves and channels, removal of the solid crust, etc. To perform all these procedures are applied in different ways.

How to cut metal at home

Homemade cutting metal is carried out using a Vice, hammer and chisel. The last tool consists of three parts – drums, middle and working. The working part is made in the form of a wedge, with the average tool holds the master drum part has a rounded end and tapers. cutting metalFor production of chisels used carbon steel. Before cutting the workpiece applied to the risks on the future site of the incision. Then the sheet is inserted into the vise so that risks were visible. The first blow is applied with a chisel horizontally, all of the following under an angle of 25-30 degrees. Cutting sheet metal – a rather complicated and time-consuming procedure, so the method described above is suitable only for processing small batches of material. On an industrial scale apply more sophisticated automated methods.

Cutting large quantities of metal

Often in small workshops and sometimes by businesses to razrubanii metal sheets used pneumatic chipping hammer. Worker holding it with both hands, guiding the chisel exactly on the intended line of cutting. Cutting metal this way you'll be less effort and is faster than the manual. To work the nail gun can both from the mains and from the compressor.

Cutting sheet metal using a guillotine

cutting sheet metalIn large enterprises, if there is a need for processing very large quantities of metal used is a special tool that dramatically reduces the time of surgery, often making the process fully automated. It is the guillotine. Cutting metal with a guillotine is made immediately along the entire length of the sheet. Before working the metal workpiece is fixed on the horizontal support of the device with a beam. Then place cutting induced the knife of the guillotine. Sheet razrushaetsya one motion of the knife. The incision is very smooth.

Recommended

Staff evaluation: system and methods

Staff evaluation: system and methods

Personnel Assessment allows you to identify how competent the employees involved in the enterprise, and it is the performance of their work – the most significant factor affecting the efficiency of the company. To clarify the impact of performa...

How to start your own business: important aspects.

How to start your own business: important aspects.

Many people, tired of working for someone else, are increasingly thinking about how to start your own business. Someone wants to open a salon, someone store, and someone enough and vegetable stalls. Before you throw in the pool with his head, it is i...

business activities. its essence and basic functions

Business activities. its essence and basic functions

The Entrepreneurial activity of the citizen – is undertaken at your own risk and independent activity, which aims to systematically profit through the sale of works, goods, services, use of the property. The citizen engaged in such activities, ...

The advantages and disadvantages of guillotine method

Cutting metal with a guillotine has a lot of advantages, such as:

  • cutting metal with a guillotineHigh speed;
  • Precision cutting;
  • High quality (seam requires no further processing)
  • Efficiency (of the metal loss is minimal).

However, this method has some disadvantages:

  • Size of workpiece is limited;
  • Steel with a high content of silicon, titanium and chromium this way it will not cut;
  • Relatively high cost of cutting;
  • Narrow the range of the thickness of the metal;
  • Limitations in terms of temperature (the rate depends on the technical characteristics of a particular model of the guillotine).

In Addition to the electric guillotines businesses frequently use manual. Their convenience lies primarily in the fact that the use of such instruments can be in any condition, even where there is no electricity.

Cutting metal – very complex, requiring attention and care, the process. With the use of modern devices designed for this purpose, you can significantly reduce labor costs, speed up processing and to make the result better.


Article in other languages:

AR: https://tostpost.com/ar/business/22779-cutting-metal-in-the-home-and-in-industrial-scale.html

BE: https://tostpost.com/be/b-znes/40197-rubka-metalu-hatn-h-umovah-vytvorchyh-mashtabah.html

DE: https://tostpost.com/de/business/39737-das-deckhaus-des-metalls-zu-hause-und-im-produktionsma-stab.html

ES: https://tostpost.com/es/centro-de/39481-el-corte-de-metal-en-el-hogar-y-en-la-escala-de-producci-n.html

HI: https://tostpost.com/hi/business/24406-cutting-metal-in-the-home-and-in-industrial-scale.html

JA: https://tostpost.com/ja/business/22337-cutting-metal-in-the-home-and-in-industrial-scale.html

KK: https://tostpost.com/kk/biznes/40593-kesu-metall-y-zha-dayynda-zh-ne-nd-r-st-k-au-ymda.html

PL: https://tostpost.com/pl/biznes/42461-r-banie-metalu-w-warunkach-domowych-i-w-skal-produkcji.html

PT: https://tostpost.com/pt/neg-cios/42083-a-colheita-de-metal-para-uso-dom-stico-e-em-escala-de-produ-o.html

TR: https://tostpost.com/tr/business/37144-kesim-metal-evde-ve-retim-l-ekli.html

UK: https://tostpost.com/uk/b-znes/41088-rubka-metalu-v-domashn-h-umovah-u-virobnichih-masshtabah.html

ZH: https://tostpost.com/zh/business/42195-cutting-metal-in-the-home-and-in-industrial-scale.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Catering as one of the types of business activities

Catering as one of the types of business activities

Virtually all aspiring business people attracted to the organization of the public food as a means of ensuring yourself, dear, "worthy old age". But almost always that is not taken into account lots of nuances, which becomes a stu...

How to attract customers to the store: a list of ways

How to attract customers to the store: a list of ways

Everyone who is associated with the sales, constantly ask the question: "How to attract customers to the store?" Don't get many customers, there is little profit. The number of buyers depends on the income of the store, and often ...

The change of the General Director: a step by step guide

The change of the General Director: a step by step guide

Director General is the sole Executive body in the company, who is elected and appointed by the shareholders. The powers of the officer of such rank involve all spheres of activity of the enterprise, both economic and economic. It...

Project car: first you need to solve technical issues

Project car: first you need to solve technical issues

Every car owner wants to see it clean and well maintained, so the business project of a car wash with high probability, will bring good income to the owner, who decided to implement it. As in any business, there are some nuances t...

The business of breeding pigs

The business of breeding pigs

Agriculture has attracted many modern entrepreneurs. Especially when it comes to this subject of breeding pigs in rural areas. This idea for business has many advantages, since nature has endowed pigs unique properties. At the pro...

Gear wheel - an indispensable part of the machine

Gear wheel - an indispensable part of the machine

Transfer or transformation of the movement in various mechanisms and devices occurs by means of toothed or worm gears. This is the most common method in modern engineering and designing various instruments.the Main element or worm...