Replacement steering tips on the VAZ-2107 must be carried out in case of their failure or after a certain mileage. Typically, the resource does not exceed 30-40 thousand km of driving on substandard roads is making adjustments – inexpensive and non-original items are destroyed much faster, there are squeaks and other sounds. Therefore, it often requires replacement of steering components. Make it pretty easy.
The VAZ-2107 and other models “classic” series is worm reducer – it allows you to convert steering wheel rotation to linear motion rods. If you suddenly noticed that the machine increased the backlash, it does not mean that you need to replace the steering ends on the VAZ-2107.
Very often there is wear of components of the gearbox have to tighten the adjusting bolt. You need to perform such manipulations are:
Be Sure to check the oil in the gearbox sump, if it is not enough, add more. Recommended oil: transmission TM-4.
Recommended
"IZH 350 Planeta Sport" – frisky Soviet bike
It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
But if the backlash did not change significantly, it is recommended to check all the other suspension components and steering. The reason that increasing looseness in the steering can be:
Therefore, before sin and the fault tips, you need to carefully inspect the state of all other elements of the suspension. Play and stranger knock may be the cause of the failure of the ball bearing and the lugs in this case are not to blame.
Ball, even when rotation of the steering wheel can produce squeaks, so before the repair, always diagnose. Sometimes you may only want to replace the dust boot of the steering tip of the VAZ-2107. If the rubber boot is torn or cracked, but the hinge is not damaged, it is necessary to make disassembly, rinsing of the element and Assembly with laying new grease.
In order to independently carry out repairs, you will need to have these tools:
Sure there was a good hammer and mounting the blades – using them will greatly simplify the stretching finger tips of their holes in the steering blocks.
All work is to be performed on the vehicle, established on flat ground and with wheel shoes under the rear wheels. It is also desirable to include the first or reverse speed – this eliminates the possibility of sliding when carrying out repairs. Almost the same manipulations you need to make when replacing short of the tail tip of the VAZ-2107 and long thrust. In the design of steering trapezoid has two short and one long thrust.
One can be adjusted in length – special crimp clamps, which are screwed elements. To replace the entire traction Assembly you will need to carry out such manipulations:
Nothing complicated, the main thing – to facilitate repairs, treating all fittings with grease. Similarly removed and a long rod connecting the pendulum arm with bipod reducer. But her replacement is rarely required.
After remove the old traction, take your measuring tape and measure their length. The problem is that you have to make adjustment of toe –yourself to do will not work, better to go to a HUNDRED and to make a diagnosis on a computer stand. After the replacement of steering tips VAZ-2107, even if you have achieved the same length the new elements to diagnose necessarily. Otherwise, when driving, the tire wear will be much faster.
Installing the new bits in the reverse sequence. Fingers ball is inserted into the steering knuckles and the holes in the bipod, tighten the screws and fix them in position with locking pins. It is advisable to purchase new cotter pins, as the old are usually covered with a layer of dirt and rust.
Article in other languages:
AR: https://tostpost.com/ar/cars/10921-vaz-2107.html
HI: https://tostpost.com/hi/cars/10931-2107.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
When you start clicks but the starter not spinning
one day sit behind the wheel of your car, insert the key and try to start the engine. But suddenly the unexpected happened under the hood, something clicks, but the starter not spinning. That is no wheezing sound after which the v...
Tires "Hankook" winter tires: owner reviews, photos
Car tires is one of the key elements to ensure traffic safety. Although some drivers ignore it, it is better not to do it because the results can be very unpredictable. It is the right choice of tyres allows to avoid most emergenc...
What kind of oil to pour into the engine? Tips for motorists
Motor oil plays a significant role in the internal combustion engine. It is the quality and properties of the thin oil film which it forms, depends on the duration and continuity of operation of the motor. So the choice and replac...
Tire manufacturers and reviews about them
All of the modern tires of the Russian production are created in full compliance with European standards. Only apply new technology. Any economical the buyer understands that it is better to buy goods made in Russia. It will be th...
Attractive sedan Dodge Avenger
the First instance of the Dodge Avenger was released in 1990. Then it was a coupe with a fairly spacious cabin and relatively good performance. Since that time the car gained credibility among motorists in many countries. The mode...
Car review Mercedes-Benz C-class
for the First time the German company Mercedes-Benz began mass production of cars of D-class in the early 80-ies of XX century. The first on the market out model 190, and then, 10 years later, it was replaced by newer. And now alr...
Comments (0)
This article has no comment, be the first!