Fuel pump replacement for "Ford Focus" of the 2nd generation

Date:

2018-03-29 01:06:12

Views:

875

Rating:

1Like 0Dislike

Share:

Table of contents:

The Operation of the engine depends on the condition of the fuel system. It produces flow and the cleaning gas mixture at the highways from the tank. The most important component of this system-the fuel pump. It can be of different types. What is this element and how to replace the fuel pump on “Ford Focus 2”? All of this – further in our article.

Characteristics

This element is used to supply fuel from the tank to the engine. Earlier cars with petrol injection mounted manual pump. Now all the cars placed electrical element. replacing fuel pump Ford focus 2Is Not an exception and “Ford Focus 2”. Fuel pump replacement on this car is complicated by the fact that the item is hidden in the tank.

Symptoms

There are several signs which can determine the damage. So, in the first place, changing the behavior of the car. The car often jerks jerks at different engine speeds, fixed “floating” idle. Motor very hard to start cold and hot.

Resources

It is Worth noting that a certain term of service, this item not. Each holder of a parameter – one the fuel pump is already in its tenth year, the other breaks down on the second. Why this run? The fact that the element is highly afraid of overheating. The pump is in the tank and cooled by fuel. Riding on an empty tank it strongly overheats, so do not pull with dressing, if the panel button light is on. The only way to keep the pump in good condition.

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

Tools

To replace the fuel pump on «Ford» 2nd generation is successful, we will need:

  • Set radkovich keys;
  • Tin snips;
  • Slotted screwdriver
  • Cloth and a drill.

As we work with a tank, you need to wear rubber gloves and protect the respiratory tract of the respirator.

Start work

The Battlefield need to find where the burned-out pump. It is located in the fuel tank. Usually, it shows the hole under the rear sofa. So, remove the second row seats and find the metal plate that hides the pump. The problem of “tricks” that they don't have holes under it. And to replace the element, you need to renew it manually. With the help of special scissors carefully cut a hole with a diameter of 25 cm and is bent towards the metal. replacing fuel pump Ford focus 2 restylingNow you see the front of the pump. So, how do you replace the fuel pump on «Ford» 2nd generation?

Remove the tubes from the fuel lines. Please note that they will be filled with gasoline, so you can stain all around. Stock up in advance a large piece of cloth. You can make it easier - slide the motor and remove the fuse from the pump. After a few seconds the engine will stall. So we not only clear the highway from gasoline, but crowstep excess pressure in the system.

Next, remove the o-ring that holds the pump itself. Using a screwdriver, Unscrew the relevant screws and remove the item out. Outwardly it will look as shown in the photo below.filter replacement fuel pump Ford focus 2Remember, the design also includes protivootechnoy glass (to hills and curves didn't run out of petrol), a pair of wires that go to 12V and the network mesh. The latter is also recommended to inspect.

Replacement filter pump on «Ford» 2nd generation

So, if the external inspection it was very dirty, it should be replaced. The filter is responsible for rough cleaning and is a dense grid, which is located at the entrance to the pump. mesh replacement fuel pump Ford focus 2It cleans all kinds of petrol from major impurities: dirt, rust and water. Replacement mesh for fuel pump «Ford» 2nd generation requires not often. But if the failed pump, we should change it. She's not usually attached to clamps or latches. The grid is set to overlap the pump tubing, so it can be removed by hand without any tools. New mesh installed the same way.

Build

After replacing the strainer and the pump itself you should check the fit of the wires chips. The glass needs to securely stay in place. The element is installed in the tank. It connects previously disconnected tube. And here comes the problem – how to close the lid? Cap was cut by yourself, so you need to figure out how to seal hermetically the maximum. You can take a plate of 30x30 cm and on corners to drill holes with a drill. replacement of a motor fuel pump Ford focus 2Then finally cut away the old cover and put the plate on the hole. We will need to drill a couple of holes in the body. Then tap to cut the thread of appropriate diameter and installed the bolts. For mounting plate, it is sufficient to use a bolt 8 or 10 mm. When choosing the depth of the hole is important not to overdo it, otherwise you could drill the tank. Moreover, this happens unnoticed, because it is made of plastic, so the boltschoose the shortest.

Conclusion

So we figured out how to replace the fuel pump on “Ford Focus 2”. The restyling has not progressed as far as we would like. The same problems with the replacement fuel pump are observed on models produced in 2008. Yes, you can do without the hole, but in this case you will have to completely remove the tank. To do this in a short time and without inspection pit is simply impossible. A HUNDRED replacement motor for pump «Ford» 2nd generation will cost about two thousand roubles excluding the cost of the item. Therefore, the most reasonable and economical solution is to replace and install the fuel tank flap.


Article in other languages:

AR: https://tostpost.com/ar/cars/4464-fuel-pump-replacement-for-ford-focus-of-the-2nd-generation.html

BE: https://tostpost.com/be/a-tamab-l/7920-zamena-benzapompy-na-ford-fokuse-2-ga-pakalennya.html

DE: https://tostpost.com/de/autos/7919-der-ersatz-der-kraftstoffpumpe-auf-ford-fokus-2-generation.html

ES: https://tostpost.com/es/coches/7925-sustituci-n-de-la-bomba-de-combustible-de-montaje-a-ford-focus-de-la-2.html

HI: https://tostpost.com/hi/cars/4467-fuel-pump-replacement-for-ford-focus-of-the-2nd-generation.html

JA: https://tostpost.com/ja/cars/4464-fuel-pump-replacement-for-ford-focus-of-the-2nd-generation.html

KK: https://tostpost.com/kk/avtomobil-der/7922-benzin-aydauysh-auystyru-ford-nazarynda-2-sh-buyn.html

PL: https://tostpost.com/pl/samochody/7923-wymiana-pompy-paliwa-w-ford-focus-2-generacji.html

PT: https://tostpost.com/pt/carros/7919-substitui-o-benzonasosa-no-ford-foco-de-2-gera-o.html

TR: https://tostpost.com/tr/arabalar/7926-yedek-benzonasosa-ford-focus-2-nesil.html

UK: https://tostpost.com/uk/avtomob-l/7924-zam-na-benzonasosa-na-ford-fokus-2-go-pokol-nnya.html

ZH: https://tostpost.com/zh/cars/4819-fuel-pump-replacement-for-ford-focus-of-the-2nd-generation.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

What kind of ground clearance is

What kind of ground clearance is "Ford Fusion" and how to increase it?

of Course, the main obstacle or challenge for imported cars in Russia is their operation in deep pits, potholes and potholes. Not every crossover will withstand such tests, not to mention passenger cars. However, there are in the ...

Traffic rules: traffic rules

Traffic rules: traffic rules

Rules of the traffic controller – this is perhaps one of the most difficult and obscure of topics related to the SDA. But they need to know, anyway. Why every driving school to study such topics as the rules of the regulator...

The engine cooling system of the car: device and principle of work

The engine cooling system of the car: device and principle of work

the engine cooling System in the car is designed to protect the working unit from overheating and thereby controls the operation of the whole motor block. Cooling is a critical function in the operation of the internal combustion ...

Ford Probe: technical specifications, pictures and reviews

Ford Probe: technical specifications, pictures and reviews

Ford Probe – a car, a joint development concerns "Mazda" and "Ford" which is the identical model under the name Mazda MX-6. They have a really similar design (because the basis of the "Ford" was based on the Mazda 626 platfo...

Ferrari Enzo: photo, characteristics

Ferrari Enzo: photo, characteristics

Sixteen years ago in France, on the motor show was presented sports car Ferrari Enzo. This model is also referred to as F60 Enzo, but before the sixtieth anniversary of the firm had a lot of time, so the name was dedicated to the ...

Totachi (oil): responses of motorists

Totachi (oil): responses of motorists

on August 29, 2012 in Moscow automotive exhibition for all drivers of the country presented a new market for our brand – Totachi. Motor oil is made in Japan. This product is very interested motorists. Let's get acquainted wi...