Pulling dents on the car with his hands

Date:

2018-04-02 03:06:15

Views:

916

Rating:

1Like 0Dislike

Share:

Table of contents:

Any damage to the body is very unpleasant for the owner of the car. Not only are they substantially spoil appearance, but also provoke corrosion processes. In the end the owner has to fully paint their car. And if you scratch things are a little better, then to remove dents is difficult. However, if you know how to perform the pulling of dents without painting, you can save considerably and to return the vehicle remains an aesthetically pleasing appearance.

There are several technologies for dealing with dents. To pull them you can use coins, vacuum equipment, technology, Pops-A-Dent, a method of heating and cooling. Let's consider each of these ways.

Types of dents

The First thing you need to determine the type of deformation. These injuries differ in magnitude. So deep is the damage, the depth of which is between 10 millimetres and more. Often, these dents do not have a clear shape of an oval. pulling dentsThese defects are not eliminated. Shallow damage – a defect where the deflection of the metal is not more than 5 mm, and on the surface of the paintwork no damage. This defect can already remove your hands at home or garage environment.

Alignment vacuum technology

This is a special technology of pulling dents without the need for staining. Using this method, even severe dents can be removed within a few minutes. The technology involves the use of special suction cups that you can level the surface of the body. This method allows to remove large and shallow dents.

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

You Should remember that using this method it is possible to correct only the dent but not the consequences – completely eliminate the traces of the accident impossible. Choosing vacuum technology, you need to consider that you have to carry out additional work. pulling of dents on carThis technology is suitable only for straightening without painting (provided, however, that on the surface no cracking). If such defects exist, the surface of the metal with the roll-out can flake off. Such item unfit for use.

For the technology, you should buy a special suction cups for pulling dents on cars. For levelling, you do not have direct and open access to the reverse side of the defect. This is an easy and fast method. The suction Cup is applied to the site of the defect, and when a compressor creates a vacuum. Then with a rapid movement pull the dent. Small defects are easily removed this way.

Extrude using the CO2 spray and blow dryer

This technology involves the presence of a can of compressed carbon dioxide and the ordinary household Hairdryer. pulling of dents on carFirst, the dent is heated with a Hairdryer. And then the surface is sprayed from the spray gas. At this point, the metal is instantly equalized and gain your previous form. When the spraying process is finished, you must wait a while, and then wipe the injury.

Repair of body defects coin

Of Course, coins are not needed. Pulling dents on a car in this way is similar to the principle of the shock or rod puller for pulling. Plus techniques that you do not need to drill holes in the body. This method is very convenient in places where the metal is particularly thin, and drill a hole impossible. The work is easily accomplished with your own hands in the garage conditions.

set for pulling dents

So, what is its essence? Technology is soldering copper or bronze circles to ordinary welding electrode. The circle for its size resembles a coin. Then it is soldered to the surface of the body – it must be pre-cleared. The circle, the coin is placed so that it was close to the dent. Then with the help of a powerful pair of pliers to squeeze the electrode, and therefore executes the pulling of dents. When the place is cleared, “coin” is heated locally and is easily removed. It only remains to sand and paint the repair area.

Auto magnet

This simple technology allows you to easily remove a dent from the surface of the body. It is worth to note that before the repair under the magnet, be sure to put soft materials. This will protect the surface of the paint from scratches. A magnet is directed from the edges of the defect to the center and draw. In the case of shallow defects fixture easy it. You do not need to paint a body.

Pops-a-Dent

This is a special plastic device, shaped like a regular clip with two “pennies” on each end. They are intended for local repair dents in a home or garage environment. To paint the repair area is not necessary. Fixture made of quality plastic. He's not fragile, but not flexible. For greater reliability, there are ribs. They give the design elasticity. The cost of this kit is 450-500 rubles. You can buy it in any automotive store. Reviews about Pops-A-Dent generally positive. Among the disadvantages motorists have noted a small number of bits.

The kit to pull the dents comprises three nozzles with different diameters at the endshave screw threaded. This thread is screwed a sheep, with which to pull dents. tool for pulling dentsNozzle rubber is applied with a special glue. It is complete with fixtures. The glue has a special formula – it is reliable, durable, but it is easy to remove without damaging paintwork. The attachment to glue on the sides and in the center of the defect. The edges of the tips of the rubber there are holes – they are made not just. At the time of gluing fixture for pulling dents excess glue can escape through these openings. Then, after curing, he will be able to give the extra effort to fix.

How to fix “bubble” after an unsuccessful drawing method Pops-a-Dent

It so Happens that the owner of the car twists a little lamb, and the result is a bubble. In this situation, the manufacturer has included a special set of pegs. They are made from unique materials for nanotechnology. Plastic peg very flexible – it is intended to repay a shock load. pulling dents with their handsThis peg is needed in the case where the dent is constricted (e.g., on the roof). Form a bubble. If you keep it in the center and not much hammering, the defect will vignette. From peg on the surface has no defects. You can Bang on it all you want, but he will not bend and will not break. As noted above, pulling dents, this method is performed with glue. For applying it, the manufacturer has added to the set melt.

So rod glue set in the gun and then wait a bit until the part warms up. Further, by means of his trigger squeeze. The glue will be good to go outside. The gun is quite high quality, and its design is very simple.

Using the kit

To remove a shallow dent without needing paint with this set, you must perform several actions:

  • Pre-degreased the center of the defect. Next, manually drive the glue gun and warm it. When the composition is heated, its squeeze trigger. While the glue is hot, smear it on the rubber nozzle. The latter is glued to the center of the dent. It is important to remember that the glue hardens quickly. At the time of bonding the nozzle screw clockwise and counterclockwise. The composition should protrude through the holes we talked about earlier. Further, the nozzle a few minutes kept at the site of the defect prior to complete solidification of the composition.
  • To ensure That the quality of adhesion, the nozzle is rotated from side to side. If everything is OK, then stick a plastic bridge across the hole in the center. Then the lamb is wound on the thread. Along with the rotation defect will catch up. With every turn of the dent rises higher and higher. You need to turn carefully so as not to get in the end bubble.
  • When the defect is aligned, the fixture holding on the surface a few minutes (the metal is not able to go back). After 5 minutes remove the Frother. But if it is not removed, then help her with a Hairdryer. At the same time all the paint will remain in place.

The Technology of drawing with the use of leverage

This method is used more often than others. But it should be noted that the technology is a little more complicated than all the previous ones. Before the pulling of dents on the car it is better to practice on any other surfaces.

You should First purchase a set of tools. The set includes about 40 pieces of different levers and hooks. Before beginning any repair work to provide easy and free access to the location of the defect. Any third party items neatly removed.

suction cups for pulling dents in auto

Work with the tool for pulling dents are only on the inside. To do this, select the hook with the optimum length and gently put pressure on the recess, thereby aligning the metal. This technology can be applied even after an alignment. It is not necessary to run the hooks, if the car was specialsa. There is a risk that the plaster will just fall off.

Conclusion

As you can see, pulling dents with their hands it is possible to implement. This repair can be performed in the garage environment without the need of costly visits of service and painting.


Article in other languages:

AR: https://tostpost.com/ar/cars/4567-pulling-dents-on-the-car-with-his-hands.html

BE: https://tostpost.com/be/a-tamab-l/8118-vycyagvanne-uvagnutascya-na-a-tamab-l-sva-m-rukam.html

DE: https://tostpost.com/de/autos/8119-rei-dellen-auf-dem-auto-mit-ihren-h-nden.html

ES: https://tostpost.com/es/coches/8124-el-estiramiento-de-las-abolladuras-en-el-coche-con-sus-manos.html

HI: https://tostpost.com/hi/cars/4570-pulling-dents-on-the-car-with-his-hands.html

JA: https://tostpost.com/ja/cars/4567-pulling-dents-on-the-car-with-his-hands.html

KK: https://tostpost.com/kk/avtomobil-der/8122-oyu-zhanshyludy-avtomobil-de-z-olymen.html

PL: https://tostpost.com/pl/samochody/8120-wyci-ganie-wgniece-na-samochodzie-w-asnymi-r-kami.html

PT: https://tostpost.com/pt/carros/8116-sif-o-de-amassados-no-carro-com-as-m-os.html

TR: https://tostpost.com/tr/arabalar/8126-esneme-ezik-arabayla-kendi-elleriyle.html

UK: https://tostpost.com/uk/avtomob-l/8122-vityaguvannya-vm-yatin-na-avtomob-l-svo-mi-rukami.html

ZH: https://tostpost.com/zh/cars/4946-pulling-dents-on-the-car-with-his-hands.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

The cheapest ATVs: overview, features, manufacturers and owner reviews

The cheapest ATVs: overview, features, manufacturers and owner reviews

In this article, we'll tell you which cheap ATVs, there are at this time freely available. This information is of interest for those people who decided to buy myself a mode of transport, but in doubt. It will also be useful to kno...

Opel Zafira Tourer

Opel Zafira Tourer

In 2011, motorists were shown the new Opel Zafira Tourer. Since the late 90-ies, when he took a leading place among the sold cars of such brands, designers were introduced and implemented some changes which have made the van more ...

The showroom,

The showroom, "Kars city Prime": reviews and opinions

Sooner or later every motorist thinking about purchasing a new car. It's always exciting moment, because you need to do a lot. You must decide what is best showroom to buy a car, find out more about the reputation of the dealer. F...

Tank A-44: Merkava model 1941

Tank A-44: Merkava model 1941

the Past twentieth century saw the rapid development of technology, including military. On creation of new samples worked and both individual enthusiasts and entire teams of designers. Some developments have significantly ahead of...

Boge shock absorbers: description, varieties and characteristics

Boge shock absorbers: description, varieties and characteristics

Serviceable shock – a pledge of security and comfort. The car with these stands better dampens vibrations and provides good traction. However, the shock, no matter how great he may be, sooner or later comes to malfunction. A...

Tractor

Tractor "Belarus": a big opportunity in small cars

Trade and economic miracle of the Republic of Belarus lies in the fact that this country was organized on its territory the production of its own products and left them on the international market. It exports, including such serio...