In the candle wells oil: what to do? Oil in spark wells ("prior")

Date:

2019-11-21 21:20:16

Views:

531

Rating:

1Like 0Dislike

Share:

Table of contents:

The car VAZ has a lot of features in terms of maintenance, and one of them – is getting oil in spark wells. The reasons for this phenomenon can be different, in many respects it depends on the specific model and engine type. Today we look at what threatens the flow of oil in spark wells and engine on how to solve this problem their hands.

candle in the oil wells

The Reasons for failure and solutions to problems

It Happens to such trouble quite often. Let us understand why. Oil in spark wells appears due to wear of the pads. In General, this problem is not so dangerous, at least not as much as, for example, getting the same lubricant to the cylinder head. Perhaps the most serious consequence of such problems – softening of the rubber insulator of high-voltage wires that in turn, will cause the breakdown. But this does not mean that you can let things drift. Noticed that gets the oil in a candle well? Immediately change the pad wells and the problem will be solved. Otherwise you'll have very often to change spark plugs (usually their life is reduced several times).


How to repair?

Why candlestick is formed in the wells of oil, we have seen, now let's talk about how to replace the gaskets. First we need to prepare all the parts and materials. During the execution of works on elimination of leaks you'll need:

  • Two gaskets valve cover.
  • 10 sealing washers.
  • Lubricant WD 40 and silicone grease.
  • 4 candle seal wells.
  • Engine Cleaner.

Having Prepared everything necessary, you can safely get to work. In General, the process for replacement of linings of wells can be divided into several stages:

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

  1. Removing the valve cover.
  2. The dismantling of the wells.
  3. Removal of old o-rings and install the new one.
  4. Reassemble.

oil in spark wells Priora

More detailed instructions

Below we take a closer look at how to repair oil in spark wells 2112-go Vase and other models of cars of the Volga automobile plant.

So, where to start? You must first remove the plastic engine cover and the receiver. All holes that are in the intake manifold is capped (it is necessary for us in order to prevent the penetration of foreign objects in detail). Next, dismantle the ignition module and PCV hose with nozzle cap cylinder block. Then use the 10 key to Unscrew the bracket bolt harness wire of the injector. Swivel key 8 15 Unscrew the mounting screws on the lid block of cylinders (it is also called a valve). After that, the machine extracted the cover of the unit.

Check hydrotalcites

Next, you need to check hydrotalcite. How to do it? It's very simple – with a punch of soft metal (or a simple screwdriver) just click on it and follow his further status. Ideally, hydrotalcite needs to cuddle up with great effort. gets the oil into the candle wellBut if you put the least amount of force, it is likely that this unit needs to be replaced. By the way, when Troubleshooting hydraulic lash Adjuster Cam camshaft must be directed to the first back side.

How to replace this item?

As to neglect replacement of the hydraulic lash Adjuster in the course of solving our problem, we can not, a few words will be devoted to the replacement of this device.

The First step is to remove the timing pulley on the camshaft and the wire from the gauge lamp oil pressure. Further, a coupling key 20 8 Unscrew the mounting bolts of the bearing housing the shaft.

Bolt, connecting rod with bracket rear engine mounts also must be removed. Next, in the same place it retrieved the 3 nuts with key 15. After that, the rear support bracket is securely fixed, and it can be safely removed (as the bearing case camshaft). Removed from the latest guide tubes of spark plugs. Further from the case removed the camshafts. Do not forget about seals.

In the next phase removed the 2 rear plugs of the cylinder block and the bearing housings of the camshafts. To remove hydrotalcite, the end parts of the magnet is applied and the item was successfully removed from the slot of the head.

Before assembling the cylinder head is thoroughly cleaned of dirt, and the bearing housing camshaft – from oil and old sealant. Further, the Cams shafts and bearing journals lubricated with new engine oil.oil in spark wells 2112

On the surface of the bearing housing which mates with the cylinder head, 2 mm flagellum is covered with a special substance (sealant) "Loctite No. 574". Further, the housing is set back into place.

Now you need to lubricate the o-ring and install the guide tubes in the holes of the cylinder head and the bearing housings. Then zapressovyvajutsja new seals of the camshaft and the back side of the block are plugs.

Before installing the cylinder head cover, on its surface it is necessary to apply the sealant (the same "Loctite", which eliminates the oil in spark wells). “Priora VAZ” , however, mayrepaired another way. What – read the article.

What to do if patterns are formed in the wells of the oil? To troubleshoot the problem, alternative way

Consider a more fast method to eliminate problems that will occur without the removal of the receiver and valve covers. However, we will need a special tool. And here, many motorists have difficulty. The fact that this tool (we are talking about the o-ring remover candle well) is very hard to find in stores, so often drivers have to make it himself.

getting oil in spark wells

How to make a puller?

It is very simple and cheap. To build the tool you need to have a metal pin with a minimum length of 15 inches, a piece of rubber hose with a diameter of 20-25 mm, a few washers, nuts and one grommet. What to do with all this? First, the long hairpin, put on a washer, then rubber bushing and nut. All - o-ring remover candle the well successfully made! The cost of such a tool is not more than $ 100, and you can do it virtually in a few minutes. So you very quickly remove the oil in spark wells. "prior" and many other models of domestic cars are repaired with the aid of this tool.

Please note that the rubber band was clamped on both sides of the washers. The diameter of the latter must be as close as possible to the width of the candle well. Otherwise, the sandwiched elastic band to come out in the gap between the shaft and the washer, and that's all we need.

Pulling handle is made from the valve nut. The lower washer should rest against the tip of the studs and top – drawn in by a sleeve.

So, to begin repairs. First puller is inserted into the candle well, and then the bottom nut is tightened to the moment when the axial movement of the tool will give us the opportunity to get well. After a little effort, the glass is successfully removed.

The progress note to the inserted stripper rubber part has not made the height for the well. In the first case, we install new seals, lubricated with oil and assemble in reverse order. By the way, the process of installation will take you less time than the disassembly.

The Nuances in the performance of work

leaking oil in spark wellsIf you decided to resort to the second option, don't forget the rules of operation and work with the puller, or remove the candle oil wells you will fail. What exactly was the issue? Explain.

First, the eraser tool should take in the candle well in full size. Otherwise, it will gradually expand, and remove the glass you will not succeed.

Second, when removing the well has a probability of bias the valve caps, which could then block the exit key. But since the wall thickness of the glass is too small with a long thin screwdriver mentioned detail easily removed.

Third, when removing the candlestick key, we need to ensure that the old lower oil seal does not come off from the scene.

Summing up

In the first case, the implementation of all necessary works we spent about 4 hours and about a thousand rubles. Using the second method, you will spend no more than 1.5 hours, as the necessity of removing and re-installing the receiver and the valve caps will be deleted.

So, we figured out why is formed in the candle wells oil and as this problem to eliminate with your own hands. Do not be affected!


Article in other languages:

HI: https://tostpost.com/hi/cars/24311-in-the-candle-wells-oil-what-to-do-oil-in-spark-wells-prior.html

PL: https://tostpost.com/pl/samochody/39714-w-wyprasek-wk-ad-w-studniach-olej-co-robi-olej-w-wyprasek-wk-ad-w-stud.html

PT: https://tostpost.com/pt/carros/39599-no-candlestick-nos-po-os-de-leo-o-que-fazer-o-leo-de-candlestick-nos-p.html

ZH: https://tostpost.com/zh/cars/49072-in-the-candle-wells-oil-what-to-do-oil-in-spark-wells-prior.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

When charging the battery boiling is normal or not? Learn why when charging battery, boiling the electrolyte

When charging the battery boiling is normal or not? Learn why when charging battery, boiling the electrolyte

Many car owners are faced with the fact that, when charging the battery boils. Someone it does not bother some, on the other hand, unplug the charger (memory). There are several important ways of how to recharge the battery to 100...

KAMAZ load depending on modifications

KAMAZ load depending on modifications

KAMAZ load varies depending on the modification. This car is not the leader in the carriage of the heaviest cargo. However, it enjoys great popularity.In the 60 years of the Soviet Union badly needed machines with capacity from ei...

Door trim 2110 – removal, installation, hauling

Door trim 2110 – removal, installation, hauling

Motorists who want to completely transform your car by tuning, should pay attention not only to its exterior and powertrain, but the interior design, one of the main components of which is cladding. Standard door panels 2110 is no...

IZH

IZH "Planeta-5": tuning not only for speed but also for the soul

the Tuning of the motorcycle IZH “planet-5” is the dream of many boys that they sometimes begin to realize only at a Mature age, when I can afford to purchase a product of the Izhevsk plant. Then to engage in “Pl...

The phased replacement of the electrolyte in the battery

The phased replacement of the electrolyte in the battery

Despite the fact that today most batteries for cars do not require frequent maintenance (often referred to as maintenance-free power sources), there are cases when this cannot be avoided. The most difficult and important service o...

Replacement of the heater radiator VAZ-2114: useful tips and important points

Replacement of the heater radiator VAZ-2114: useful tips and important points

When it comes to what you need to replace the heater radiator VAZ-2114 there is a huge amount of complexity. For example, it is impossible to disassemble the device or, on the contrary, there are difficulties with the installation...