The purpose of the motor the stove is to increase the efficiency of heating and air circulation in the cabin. Quality heating is significantly reduced when it breaks. There is also the likelihood of extraneous noise which irritates the driver and distracting. The solution is to replace or repair and how to remove a motor the stove is not difficult, you can not go to service center and conduct all the work yourself.
The Search for the causes is the first stage of the work. You need to start the car and listen to the sounds that appear when you switch the device on various modes of speed. If the motor does not work the stove, it is easy to identify by the lack of sound and no action after power up. Resistor available in the switch, also may cause the fan start only in third gear.
There are several other faults that cause failure of heating:
Recommended
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...
The switch Itself often leads to problems. Using standard light bulbs with soldered wiring, you can check the device. To ensure free access to it, turned off the main part of the console. With the engine off, one wire is placed on the “minus”, the other touches all speeds separately. When triggered, the lamp on each element it is possible not to doubt the health of the switch. In the absence of reaction the wire is placed on the “plus”. The lamp should turn on, and if not, possible breakage of the fuse, or the motor of the stove is open in circuits.
It Is necessary to understand the principle of operation of the system. Setting the temperature to the desired level is carried out by closing and opening the valve element heating. The radiator receives the heat source – warmed coolant, the temperature of which is heated when the engine reaches 95 degrees.
Speed is set by the mode switching speed. This has a direct impact on the amount of cold or heated air entering the passenger compartment. After varies the supply air panel valves, they regulate the direction, for example, in the cabin or on the windshield.
If the fan does not work either noted the occurrence of noise and squeak, may have to change. For a start prepare the tools: ratchet handle, screwdriver, cross and crown.
Unscrewed the screws used for fixing plastic covers near the windshield, which was subsequently removed. It will interfere with the work, as well as the seal of the hood.
Pull out the protective cover that hides the motor of an oven, and vivenciada bolts, fixing it to the vehicle.
The driver's side in the cabin need to find the fan wire from the positive value to push it. Next to him is a negative lead, a mount which is removed by means of a head of a suitable size or stick with the rattle. Other options of relief available, as the device offers a direct method of podpici transaction. Before you change the motor of an oven, it should twist to simplify the process. With knowledge and time can fix. In another case, mounted the new unit and all items are returned in the reverse order to that specified.
To start is to check if there are foreign objects inthe duct, as they can contribute to noise in contact with the impeller. If they are not, you will have to disassemble the motor. The disassembly process is similar for different types of devices.
You Need to pull the anchor, this allows access to the brush site, by removing the fan cover. Cleaned and lubricated the bushing, located on the housing and cover.
Bearings are thoroughly washed in kerosene, previously withdrawn from them boots, made of rubber and are lubricated with petroleum jelly. This algorithm often allows you to return the bearings performance.
If necessary, they can be replaced by a new one. At the same time before removing the shaft marked seats. To remove you can use a screwdriver or a core, but the best option is a dedicated puller.
Insertion of a new element is done with a hammer or wood block, it is desirable to apply machine oil on the stock.
The Collector should be cleaned from possible oxidative phenomena, before assembling the motor the stove. Due to this, the conductivity of the brush will improve. Lubrication of the fan with petroleum jelly will provide easier mounting in a plastic glass.
Article in other languages:
AR: https://tostpost.com/ar/cars/20397-the-motor-of-the-heater-repair-and-replacement.html
BE: https://tostpost.com/be/a-tamab-l/38059-matorchyk-pechk-ramont-zamena.html
DE: https://tostpost.com/de/autos/37676-motor-kochherde-reparatur-ersatz.html
ES: https://tostpost.com/es/coches/37446-los-tel-fonos-de-la-estufa-reparaci-n-sustituci-n.html
HI: https://tostpost.com/hi/cars/22082-the-motor-of-the-heater-repair-and-replacement.html
JA: https://tostpost.com/ja/cars/20055-the-motor-of-the-heater-repair-and-replacement.html
KK: https://tostpost.com/kk/avtomobil-der/38446-pesh-motory-zh-ndeu-auystyru.html
PL: https://tostpost.com/pl/samochody/39996-tarczyca-pieca-naprawa-wymiana.html
PT: https://tostpost.com/pt/carros/39647-motor-do-fog-o-de-repara-o-substitui-o.html
TR: https://tostpost.com/tr/arabalar/34921-bir-makine-var-soba-onar-m-yedek.html
UK: https://tostpost.com/uk/avtomob-l/38862-motorchik-p-chki-remont-zam-na.html
ZH: https://tostpost.com/zh/cars/22726-the-motor-of-the-heater-repair-and-replacement.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
"IZH 350 Planeta Sport" – frisky Soviet bike
it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...
Salon VAZ-2114 and its features
continuing the series of “Samara-2” in 2001, the domestic auto industry introduced the hatchback with five doors of VAZ-2114. The distinctive features of the models have the front end (headlights, grille, hood, bumper)...
The Car "Tavria". Tuning with your hands: features and recommendations
Every car requires enhancements and improvements, especially if it is produced at the plant "ZAZ". Tuning ZAZ-1102 “brand” – is the completion of the famous Ukrainian of the car, which received the status of nati...
"Nissan Almera": tuning with their hands, description, features and reviews
To improve the technical qualities of upgrades, car «Nissan Almera”. Tuning involves multiple changes to the structural elements of the car. This includes: replacing parts of a body, interior, suspension and engine. Th...
the Tractor DT-20 is a legendary wheeled tractor, produced at tractor plant in Kharkov from 1958 until 1969. Just came off the Assembly line 248 400 cars.Demandthe Kharkiv tractor plant produced the model DT-20 for export. Thousan...
Tuning "Chevrolet Epica": description, features and recommendations
Tuning “Chevrolet Epica” is the change of structural elements or the replacement of parts to modified, contributing to the improvement of the technical characteristics of the car. These improvements are designed to inc...
Comments (0)
This article has no comment, be the first!