How to bleed brakes on VAZ-2106 with his own hands

Each motorist needs to know how to bleed brakes on VAZ-2106, or similar model. Speaking roughly, then bleeding the brakes on all the cars (without ABS) is the same, even the same scheme. The difference can be only in the machines with right-hand steering – in their scheme of flow is reversed. But as the cars “classic” series have LHD, the air tube from hydraulic brakes wykonawca the standard scheme.

When you need to leveling?

The work is Carried out in such cases:

1. Replace the brake pipes.
2. Replacement of calipers, front disc brakes, VAZ-2106.
3. Changing the brake hoses.
4. Install a new master cylinder (and repair).
5. Replacement of the fluid in the hydraulic.
6. Installing new cylinders on the rear wheels.
7. Replacement of a regulator of pressure of brakes.

If you had to get into the design of the brake system, be sure to make pumping – this will improve efficiency, reduce stopping distances.

What you'll need for the job?

To carry out the work, collect such tool:

1. Find a small transparent jar. You can trim the plastic bottles of 0.5 liters.
2. Required that you have a transparent tube – perfect that which is installed in the system washer windshield.
3. Brake Fluid (always the same brand that was filled earlier).
4. Penetrating Grease type WD-40. It will need to handle all threaded connections.
5. Key crimp terminals for the brake system.
6. The Key to “8” and “10”

You might Also need pliers, Jack, shoes, and other instruments.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Training for repair

Before you can pump the brakes on the VAZ-2106, need to do preparatory work. To do this:

1. Place the vehicle on the pit. With its help to carry out the leveling – access to the fittings easier.
2. Treat all fittings penetrating lubricant and wait 10-20 minutes more.
3. Make Sure that all prokachannye fittings out. For this you need to use a cap or crimp key – carob can not work, as it will only hurt face.
4. Make Sure that in the reservoir a sufficient amount of fluid, if necessary top up.
5. Verify no leaks in the system. If any, repair.

Is allowed in the expansion tank foreign objects – it will cause damage to the brake master cylinder and clogging the pipes.

The Order flow

And now more about how to pump the brakes on the VAZ-2106. First you need to implement the pumping of the rear wheels:

1. Establish a transparent tube over bleeder valve priming right wheel, its other end should be dipped in a jar of brake fluid – so you can control the withdrawal of air from the system.
2. Have an Assistant repeatedly press the brake pedal until it stops, then lock it down.
3. Loosen the tightness of fitting – liquid go through the tube and the pedal fail to the floor.
4. Repeat the points “2” and “3” several times, until you stop the air bubbles in the tube.

After pumping right wheel go left and perform a similar manipulation – get rid of air in the system.

Then the same actions produce the right front brake mechanism. The pedal must be pressed harder – in the system becoming less air. Here's how to pump the brakes on the VAZ-2106 self – sufficient only to maintain order. And closely monitor the fluid level in the expansion tank.

All work is to be done without an assistant – for this the tank will need to create high pressure. Usually for this purpose use a simple inner tube and cover with a fitting and valve. But in this case, the fluid loss will be a little bit more.