Impossible to doubt that the reliability of the roof is one of its important characteristics. The basis of this design are the load-bearing rafter farm. Their installation can be called responsible and time-consuming job that involves carrying out exact calculations. Rafter system needs to endure the weight of covering materials, insulation, sheathing and atmospheric precipitation in the form of ice and snow. Considering all these factors, the rafters should give maximum strength. They can produce its own, however, it is important to consider the region in which a building was erected, and all its features, including wind and snow loads. This includes seismicity of area of construction.
Wooden farm are collected from the suspension and the sloping rafters, mauerlat, ridge runs, struts, diagonal ties and struts. Connected parts form a truss farm, which has the form of a triangle or multiple triangles connected to each other. The carrier portion of the roof structure – is a system of rafters are called rafter feet. The angle at which they are set, matches the angle of the roof.
Wooden farm with his own hands manufactured according to the technology, which involves the installation of rafters on mauerlat, located on the wall. This is required for even distribution of weight. In the upper part are connected to the ends of the rafters and run, the latest of which is called podkorytovym beam. In this part there is a ridge of the roof. The distance between the rafters must be determined by the characteristics of the material of the roof section rafters, and other factors. This parameter varies from 0.8 to 2 m.
Recommended
The most effective methods of seed germination
Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...
Retro-reflective paint. The scope of
When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...
How to make icon with your own hands - options izgotovleniya (simple and complex)
In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...
Wooden farm, as mentioned above, consist of the rafters. They should be placed parallel with the rays, as their goal is elimination of deflection of the roof structure. If we are talking about the run, it is executed in the form of a cross bar, which is located longitudinally on the top. To support purlins truss are struts and sleepers. The components of the secondary trusses – braces, thanks to them ensures the stability of the rafters.
Calculation of a wooden farm, of course, best left to professionals, in the course of these papers should take account of load, which are called permanent as well as temporary and special. The first is the weight of the components of the roofing. While the temporary load – weather precipitation and weight of people who can climb to the roof for repairs. This should include the wind factor.
Special loads are those experienced by the building in areas with high seismic hazard. The most important is the calculation of the snow load, which is performed by the formula: S=Sg x μ, it's Sg – weight of snow load per square meter. This parameter is conditional and value is determined by a table depending on the region. With regard to the values of μ, it is a factor that depends on the angle of the roof. To determine the wind load, need to know which zone the house is located, it can be open space or urban development.
The Design of wood trusses calculated still on the basis of the standard value of wind load in a certain region. You must take into account the height of the building. But in order to determine the distance between the rafters should be aware of their cross-section and length. If the cross section of the beam is 8x10 cm and the length of the rafters does not exceed 3 m, the distance between these elements should be 120 cm With the increase of the cross section of the beam to 8x18 cm and the length of the rafters up to 4 m distance will be equal to 140 cm. as the maximum value is the section, which is 10x20 cm, while the length of the rafters should not be more than 6 m, the distance between them will be equal to 140 cm.
As for the rest of the roofing system, they should have the following sections: mauerlat – 10x15 or 15x15, diagonal truss legs – 10x20, tightening – 5x15, struts – 10x10 and runs with the latter sections.
It is Important to know the cross section of the girders and blind stitch boards, in the first case the value will be 10x15, whereas in the second – 2,5x10 cm If you will install roof trusses are wood, you will easily be able to calculate the required number of elements, knowing the cross section of the rafters and length. It is important to know the step of installation.
In the first stage, the wizard requires to create a template, which will be further work. The rafters have the same type of design, so a template saves time and effort. Two boards, one edge should be connected with a nail, the result is a design that resembles a pair of scissors. When performed wooden farm with his own hands, the free edge of the received scissors have to be installed on the support locations of the rafters.This will allow you to determine which slope will have slope roofing.
An Extra set of nails will allow you to position the angle, which is between the boards. At this stage we can assume that the template is ready. Additionally, you can fix it with a cross bar. In order that the angle did not change under load, the rail can be fixed with screws.
If you decide to manufacture wooden farm, you should be careful when creating the template, even if it will have minimal deflection, all design mowing. The next step is to implement a new template for preparation of the grooved elements of the system. In this case you should have a 0.5-cm plywood for fixing you should use a Board thickness of which is equal to 2.5 cm.
The Rifling should be selected given the cross section of the rafters. When manufactured roof trusses are wooden, with ready-made templates, you can make a thread and to start a farm.
Article in other languages:
KK: https://tostpost.com/kk/domashniy-uyut/19294-a-ash-itar-aly-z-oldarymen-rylymy-esepteu.html
TR: https://tostpost.com/tr/domashniy-uyut/19301-ah-ap-iftlik-kafes-elleriyle-tasar-m-hesaplama.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
Punch "Hitachi DH24PC3": overview, user manual
If you want to facilitate repair work on the house or scheduled construction site, then you must select the appropriate equipment. As one of them acts as a hammer, which must be of good quality but not too heavy for the house mast...
Table grape "Transformation". Description and features of cultivation
the Sort of "Transformation" – early grape ripening. It is obtained by crossing two cultures - the "Talisman" and "Sultana" varieties "radiant". Grape "Transformation" is distinguished from other varieties of high, stable yi...
Rolled roofing materials. Advantages, disadvantages, principal
roofing materials widely used in constructing roof. Roofing is one of the most inexpensive and simple manufacturing technology. Despite the relative cheapness, with all the technology four layer coating of roofing material will se...
The thickness and size of floor tiles. Dimensions of floor tile for kitchen and bathroom
Paying tribute to fashion, people use the latest materials for the construction of houses, not thinking about their durability and resistance to wear, and if the number of works can not particularly fussy, choosing the materials a...
Pump "Irtysh": specifications and reviews
Pumping equipment in use today in many areas of human activity. Pump «Irtysh” is no exception. It is presented for sale in different versions, among others should highlight those that are designated by the letters PF. ...
How to make a suspended ceiling with your hands?
Create a false ceiling with your hands will help not only to reduce the complexity of the manufactured ceiling repair, but also to expand the possibilities of decoration. Suspended ceilings will be divided into two types. Some req...
Comments (0)
This article has no comment, be the first!