How to make oven of the disks with their hands: step by step instructions. Oven under the cauldron

Date:

2018-03-24 08:47:17

Views:

544

Rating:

1Like 0Dislike

Share:

Table of contents:

Many masters today are made by wood stoves and boilers, using a thick-walled tube. But sometimes such products become too expensive, while on hand may be a few old drives from the machine. With this you can make a stove that will be absolutely free. Only have to work on the design using their own skills and ingenuity. Some masters and even create such "works of art" that deserve attention.

Such design is attractive not only performance, but also the thickness of the metal. The body will burn out fairly soon, especially if you use the wheel from the truck. Last used for the manufacture sauna stoves, as different dimensions and the impressive thickness of the metal. For stoves, which is quite often working with large loads, this factor cannot be called unimportant. If you use commercial CDs or car, you will be able to make a wood burning heater for garage or small oven for barbecue.

Training tools

furnace of the disks

If you use the hearth for the cauldron or a conventional oven, using a car drives, you need to ensure you have the correct tools, these include:

  • Welding machine;
  • Electric drill
  • A chisel;
  • Hammer;
  • Wheels;
  • Paint brush;
  • Line;
  • The grinder;
  • Hacksaw at metallo;
  • Molotok;
  • Napilnik;
  • Ploskorezy;
  • Ruletka.

Primechatelno that almost any of the models on the basis of drives to be portable, which is very convenient, because use of this design can be in the bath or on the street. Best use a steel stamped wheels, whose diameter ranges from 40 to 50 cm and Their height may be 25 see the Hearth for the cauldron, and stove, can not be made of aluminum disks, as well as those that are made on the basis of aluminum alloys.

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Manufacturer of the furnace in the form of heat

oven under the cauldron

If you decide to make a furnace of the disks, you can take the design of Buleryan. The original will cost rather decent money, but the product, made by hand, cost less. If you'll find three wheels of GAZelle or UAZ, you can assume that half the work is already done. Will need sheet metal and pipes, the diameters of the latter must be equal to the limit from 100 to 150 mm. Prepare a short pipe, with a diameter of 76 mm.

When baking is performed from the disks using this technology, the most difficult part is to cut out the inner part. Grinder, the work is not very convenient, because the metal is quite thick. It is best to use a cutting torch, but if not, will fit the first of the above instruments. With the help of welding machine drives must be tightly assembled so to form a casing. The back part of the need to close a metal sheet to which is welded the flue pipe. On this pipe if you wish, you can set the choke, it will allow you to regulate cravings. However, the presence of flap is not required if the furnace will have a control of air supply. For this door, located in the front, you need to embed the pipe with a damper with spring-loaded axle. Inside the firebox is mounted a plate which will divide the space into two parts. More clear this method will be, if you are familiar with the design Buleryan. Will be located on top of the secondary chamber, where the welded pipe of the chimney. When oven is made of disk-based Buleryan, the design can be of any diameter, orientation in space and length. All will depend on what the disk size and the number of them.

Making a large furnace for bath

hearth for the cauldron

For such works wheels from passenger cars will not be enough, as they have a small diameter. It is best to stock up on old rims from the truck ZIL-130. They are used in number 4. To be items must be one above the other, each will do their part. The first product will be a cap for the combustion chamber. Stove will have a small firebox out of brick, it should be provided with doors, which should go in the dressing room. Heater will be the second rim, while the third will serve as an additional heat exchanger. It will take away energy of the gas and transfer it inside the steam room. The last disc will be a tank for heating water.

What you need to remember in the manufacture of stoves

furnace of the disks with their hands

When made from the stove drives with their hands, the combustion part is usually made of red thermal brick, which is placed on a clay solution. If the dimensions of the enclosure equal to 625x625 mm, you will need to purchase approximately 60 bricks. When you install a second rim should be positioned with the hub down, just so it will be possible to have sufficient amount of gems. To the Central hole of the hub is welded the lower end of the tube segment, its length should be 50 cm.

On Top of the rim is necessary to fix the lifting plate to water. In the disknumber 4 should drill a hole for the pipe with a valve for filling the tank with hot water. The wheel, which will be filled with water, must be released from the hub. From the bottom to the rim is welded to the surface of the steel sheet, the thickness of which varies from 4 to 5 mm. In the Central part holds a hole to which is welded the lower end of the second tube, the hole should go into the pipe and germetizirujut walls.

Reference

furnace of wheels

When running the oven of the disks for the bath, you can do without a brick furnace. It is in this case arranged inside the first rim. However, to heat the bath will have a steam room, in addition, tight-fitting doors in the hull will be much harder to do.

Features at rims

furnace of the disks to the cauldron

Burning in the firebox the wood will give its heat through the walls of the first rim, which is cut out the bottom. It is welded to the second disc where the bottom is in place, this means that you can fill it with stones. Inside the pipe, it will leave the products of combustion. The pipe should go inside of the third rim, where instead of the bottom standing divider gases. It is made of sheet metal. The last stage of cooling of the gases takes place inside the latest rim that has a tank with a tap and lid. Furnace due to works better than the factory models, but for durability it is even better than any of them.

Stove for cauldron and barbecue

oven motor drives

Oven under the cauldron can be used as grill. This device can serve only two drive wheels from cars. If you need more design, then there are no restrictions, you can use wheels from GAZ-53 and Oise. One of them cut through the bottom, and then rim are welded to each other. The unit must be installed securely on any surface, to the bottom section of the legs are strengthened with the use of welding apparatus. The holes for the hub need to stop, while the side holes are left, through them in the furnace to permeate the air. To carry the case conveniently, it should be welded on the outside of the handle and on the side to make opening for installation of the door. The latter must be done from a piece that sits on the hinges. We can assume that the baking of the disks at the ready. As practice shows, it can fit the cauldron, and if necessary – five skewers of meat.

Note

After you have completed oven under the cauldron, throw the bottom disc is not necessary, it can be a stand for pots, pans to the kettle. This item will perfectly fit the exterior of your site.

Additional recommendations for work

In addition, it can be noted that on the other side of the door to set the pipe for the chimney, while there is enough diameter in the range from 50 to 70 mm. the Tiles can be slightly altered, because when working through the lower hole will Wake up ash, it's not always good. The holes must be drown, and the flow of air can be adjusted using the door of the firebox.

Recommendations for the arrangement of the upper part of the disk furnace

A Makeshift oven of the disks in the upper part must have an iron bottom. The thickness of the steel plate should be equal to 8 mm. This capacity will be used for water heating. The volume of this boiler is approximately 95 years, however this volume will heat up quite quickly, because it passes through a flue which is too hot. To the pot of water was convenient to use, in its construction it is necessary to turn on the faucet. The chimney on the top is fixed, it is strengthened cover. At the final stage of the construction and installation of structures should be put through the ceiling and roof pipe. To isolate construction from wooden materials and other flammable objects.

A Matter of integrity

When you bake discs of KAMAZ vehicles or any other brands, it is important to weld the joints of the structure as possible. This is because in the process of work and the smoke will penetrate through the cracks and get inside the bath. It can not be called pleasant and safe. Great attention should be paid to joints. After some period of use of the furnace from exposure to high temperatures may develop cracks, however they can be easily removed by treating with clay, and sprinkle dry sand. This will allow time to detect new cracks.

Before you start to operate the heater of the car wheels, you must handle it with paint that is resistant to vibrations high temperature. The upper part of the structure it is important to pay special attention to, because that is where the evaporation of the liquid. The metal loses its qualitative characteristics and corrode. The chimney flue will best complement the stainless steel sheet. Hot water will have a negative impact on any design. For fixing is possible to prepare the clamp, which is carried out independently or purchased in the store.

Fire safety Rules

When baking is performed from the disks to the cauldron or furnace for a bath, it is important to observe the rules of firesecurity. The bottom should be made of wood, it is important to establish the design on the refractory surface. The front of the room with the furnace must be installed with refractory shield which has the form of a layer of iron with dimensions 20x30 cm Width should be slightly greater than the door itself. At the perimeter of the bottom, you should install additional insulation. And the gap between the insulation and the stove is usually covered with dry sand, which is laid on top of stones. In this case the furnace of the wheels will work without becoming a source of dangerous situations.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/2958-yak-zrab-c-pech-z-dyska-sva-m-rukam-pakrokavaya-nstrukcyya-pech-pad-ka.html

DE: https://tostpost.com/de/gem-tlichkeit/2957-wie-man-den-ofen-von-disks-mit-ihren-h-nden-schritt-f-r-schritt-anleit.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/2962-como-hacer-un-horno-de-discos-con-sus-propias-manos-instrucciones-paso.html

KK: https://tostpost.com/kk/domashniy-uyut/2960-alay-peshke-b-r-disk-lerd-z-oldarymen-adamdy-n-s-auly-pesh-astynda-y-m.html

PL: https://tostpost.com/pl/komfort-domu/2961-jak-zrobi-piec-z-p-yt-w-asnymi-r-kami-instrukcja-krok-po-kroku-piec-po.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/2958-como-fazer-ondas-das-unidades-pr-prias-m-os-passo-a-passo-ondas-abaixo.html

TR: https://tostpost.com/tr/domashniy-uyut/2965-nas-l-f-r-n-s-r-c-kendi-elleriyle-ad-m-ad-m-talimatlar-f-r-n-alt-nda-k.html

UK: https://tostpost.com/uk/domashn-y-zatishok/2961-yak-zrobiti-p-ch-z-disk-v-svo-mi-rukami-pokrokova-nstrukc-ya-p-ch-p-d-.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

The furniture series

The furniture series "Hemnes" in the interior of the apartment

Firm IKEA has been manufacturing furniture for several decades and has extensive experience in this business. A series of "Hemnes" — is a series of furniture, made in a Scandinavian style. This style is a wide range of inter...

Boiler: how to install your own hands. Step by step instructions, recommendations

Boiler: how to install your own hands. Step by step instructions, recommendations

Equally in demand today, the electric heater and boiler. How to install this equipment, will be discussed in this article. With the help of this device you will be able to cope with the problems of disconnection of hot water. In a...

Table vertical drilling machine 2М112: specifications, reviews

Table vertical drilling machine 2М112: specifications, reviews

Drilling machine 2М112, technical characteristics of which are given below, has a compact size, and functionality. This allows you to use it as a desktop equipment. Great value and quality makes this device popular in various indu...

Press for metal-plastic pipes. Press crimping tool for plastic pipes

Press for metal-plastic pipes. Press crimping tool for plastic pipes

In the process of installation of the pipeline rarely do without crimping. In essence, this is a simple action that may be performed by a layman at home. However, quality implementation procedures still requires the appropriate to...

The lady's slipper Orchid

The lady's slipper Orchid

for the First time the word “Orchid” arose in my mind when reading detective novels, where the detective Nero Wolfe all free time spent in his greenhouse. In aloe timesnow the era could not understand how it was possib...

How to grow peach in the middle of Russia?

How to grow peach in the middle of Russia?

Trees with velvety and very juicy fruits known as peaches belong to the rose family and are included in the subgenus almonds. Externally, they differ very little from other plants of this class. However, they have one, but signifi...