Spiral drill: description, application

Date:

2018-04-01 04:15:14

Views:

832

Rating:

1Like 0Dislike

Share:

Table of contents:

In the Arsenal both home and professional masters should be a variety of available tools. Drill is indispensable for the implementation of a whole range of works. Today there are many varieties. However, the drill spiral is most prevalent. This is due to a number of its features and functions. The device of this tool and its scope of application deserve special attention.

General information

A Drill is a cutting tool element, which makes holes in various materials. There are many varieties. Choose the type of mill, based on the characteristics and working conditions. According to its characteristics, drill bit for rotary hammer, drills should be harder than the material.

The purpose of the different drills. They can be used for processing metal, wood, concrete, glass, tile. Each tool, depending on destination has its own peculiarities.spiral drill

The Greatest distribution was received today by the drill spiral. It is called a screw. It has a cylindrical shape and has a number of design features.

Drill Device

The Auger spiral has three main elements. This is the working part, the shank and neck of cutter. In the first section there are two helical screw grooves. This cutting element. Also they are well evacuate the chips from the workplace. If the equipment has this ability because of these grooves, the lubricant is supplied to the area of drilling.
drill bit for wood spiral

The working part consists of cutting and calibration Department. The latter is also called a ribbon. Is a narrow strip, which continues the surface of the groove on the cutter. The cutting division consists of two main and two support edges. They are located along the cylinder milling spiral. Also, this part considers the cross edge. It has a conical shape and located at the end of the drill.

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

To secure a foothold in the machine or hand tool cutter has a shank. He may have the paw for withdrawal of the drill from the socket or the leash. The latter provides a torque transmission from the tool holder.

The Neck is desired to release the abrasive wheel, when grinding of the work piece.

Product Features

Drill bit for rotary hammer, machine, which have a spiral shape, the most popular today. This is due to their special characteristics. They are well directed in the hole, and also have a large supply under the regrinding. Due to the design of such a cutter is well removes chips easily and delivers lubricants to the working surface. These features make the presented with a variety of drills are very popular.

Correct designation of the geometrical parameters have their designations. The diameter of the drill may be very different. However, designations remain the same. The angle of the tip at the top is referred to as 2φ. The pitch of the groove is denoted by ω, and terminal transverse edge – ψ. The front corner on the drawings referred to as γ, and back – α.

All together these indicators are called geometry. It reflects the position of the grooves, the cutting edges and their angles.

Types of tool

Classification of cutters takes into account such an important figure as the shape of the shank. It can be of the following types:

  1. Milling Cutter with cylindrical shank (GOST 2034-80).
  2. Drill with a conical shank (GOST 10903).
  3. A Tool with a conical shank (GOST 22736).

To master was the ability to perform all its tasks, drill produce a variety of types. In the first embodiment, the cutter is mounted in trehserijnogo the Chuck or other fixture designed.

Spiral Drill with cylindrical shank can be made in the short, medium and long version. Such a tool has 3 class of accuracy: high (A1), normal (V1) and normal (In). They can be manufactured as welded and seamless way. The shank must not have circular cracks, lack of fusion or pitting.drill with a conical shank

Conical varieties are mounted directly in the spindle equipment go transition sleeve (if the size doesn't match).

Taper shank

In the manufacture of cutters with taper shank presents the type of use several different standards. The spiral auger (GOST 10903) is applicable to the products of normal length. This group also includes several standards that are used in the manufacturing process is long, elongated cutters. These tools can be manufactured with a neck or without it. And its size is not regulated.drill bits for rotary hammer

The Cutter with taper shank (GOST 22736) reglamentary release of products with a diameter of 10-30 mm, which have a carbide plate. They can be made in a cropped or normal form. Class of accuracy for these products can be increased (A) normal and (B).

Drill with a conical shank with a diameter greater than 6 mm are produced in a welded way. For narrower cross sections may be used one-piece type of production.

Drill bit for metal

In Addition to breakdown mills on the principle of the formof the shank, there is a classification regarding the material processing. The cutter may be designed for metal, concrete, there is also a drill on a tree. Spiral workstation is applicable for all kinds of material. The only difference is the design of the tool.spiral drill GOST

Depending on the type of metal, select the drill type. They are applicable to alloy steels, unalloyed steels, cast iron, alloys, non-ferrous metals. Sometimes they are used for processing hard plastics. The thickness and hardness of the working area depends on the durability of the appliance. It is a universal type tool. A metal drill bit can drill a hole even in the wood.

If the tool sinks slowly and strongly heats the material necessary to make its sharpening. If its diameter does not exceed 12 mm, the procedure is performed manually. But for larger mills used for grinding of special equipment.

Drill bit for concrete

One of the most difficult machining materials is concrete. It requires the use of a special tool with fatty plates of hard alloy. They are called peaches. Today, any carbide nozzles are called this way.drill bit diameter

Such a tool in the process of material processing leaves a hole with a diameter larger than the drill itself. This is due to his beating. If you are using a drill, the drill shank may be cylindrical. For punch use a different type of mount. It's called SDS. There are several types. This system allows you to quickly change accessories drill presses and other equipment.

Sharpening such drills possible. However, be sure that the tool is not overheated. Otherwise, you can fall off a carbide insert.

Drill bit for wood

A Good drill for wood spiral is made from ordinary high strength steel. This material does not put forward serious demands on the material of cutters, form. This is the ordinary drill. Quite simply can be screwed into soft wood or particle Board screw plain. You do not need to use a drill. However, there are situations where it is indispensable.spiral drill with cylindrical shank

If you want to make a hole up to 600 mm deep, you should use a spiral variety of cutters. Their diameter can be from 8 to 25 mm. their Length can be different. This is useful if you want to make non-through or through-hole. If required, use the extension cable.

When carrying out drilling drill after a few turns removed from the material, clear of chips. Then continue to work. Their length can be 300, 460 and 600 mm.

After Reviewing the main characteristics and uses of such a tool, like a drill spiral, everyone can choose for themselves the right kind. This is a very popular type of cutter. Their unique quality, a wide range of applications make them very popular.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/11598-sverdzel-sp-ral-nae-ap-sanne-prymyanenne.html

DE: https://tostpost.com/de/gem-tlichkeit/11600-bohrer-schraubenartiges-beschreibung-anwendung.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/11606-broca-espiral-descripci-n-la-aplicaci-n-de.html

KK: https://tostpost.com/kk/domashniy-uyut/11601-sverlo-spiral-noe-sipattamasy-oldanyluy.html

PL: https://tostpost.com/pl/komfort-domu/11595-wiert-o-spiral-noe-opis-zastosowanie.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/11589-broca-de-fresamento-helicoidal-descri-o-aplica-o.html

TR: https://tostpost.com/tr/domashniy-uyut/11602-matkap-spiral-a-klama-uygulama.html

UK: https://tostpost.com/uk/domashn-y-zatishok/11600-sverdlo-sp-ral-ne-opis-zastosuvannya.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Finnish moonshine machine suchoparek

Finnish moonshine machine suchoparek

Manufacturing of moonshine at home has always been associated with many different difficulties. Previously, it was necessary to have all the equipment to buy was not so easy. Many artists and craftsmen have produced it yourself, t...

The interior of the Cabinet: photo. The interior of the Cabinet in the apartment and a country house

The interior of the Cabinet: photo. The interior of the Cabinet in the apartment and a country house

nowadays more and more people prefer working from home. It is easier, more economical in terms of time spent and tools (tubes, gasoline, etc.). However, if you start your business in the apartment or country house, you must need t...

Compendium (shrub): a charming ornamental plant in your country

Compendium (shrub): a charming ornamental plant in your country

One of the most beautiful flowering shrubs are Dali – they are named after Johann baths Deutz, the former mayor of Amsterdam in the nineteenth century. Has aimed this botanist Carl Thunberg, the Deutz grateful for the fundin...

Unit ventilation: characteristics, application, advantages

Unit ventilation: characteristics, application, advantages

Block ventilation – concrete structure, which is widely used in the construction of residential and public buildings. Installation of ventilation units becomes possible to organize a simple and effective ventilation of kitch...

Best tomato seeds for greenhouse polycarbonate

Best tomato seeds for greenhouse polycarbonate

a Good crop of tomatoes in the greenhouse you can get, selecting the right variety. First of all, it needs to be suitable for cultivation in greenhouses. When purchasing planting material should take into account some other factor...

Country toilet: dimensions and design

Country toilet: dimensions and design

Villas currently available for the majority of urban residents. Usually they have already furnished. However, if the land purchased recently, have to make some effort to make the stay in a country house guests. This applies to all...