Cleaning of the gas column own hands. The device of the gas column

The Gas column is relatively affordable and simple structurally. It contributes to the attainment of independence from the Central supply. Because quite often the Central network suffer outages and planned outages of the water for a long time. In order for the column lasts as long as possible, it will from time to time must be maintained, periodically exposing cleaning.

Why the need for a cleaning column

Cleaning of the gas column is required due to the fact that some important components of equipment covered by the scale. The task column consists in heating water by combustion of gas. The device can be attributed to two varieties of appliances – plumbing and gas.

If we are talking about the gas of the device, there is accumulated soot, a soot, from which the unit periodically needs to be released. Need to be cleaned still and the nozzles that constitute the hole igniter and burner. But the scale – the salts that are insoluble in hard water. They fall out as a precipitate by evaporation of water and end up on the tube walls of the column.

As a rather important problem is the scale, which prevents the heating of water. If the elements of the insoluble salts were in the channels of the thin tubes, it will reduce the efficiency of the equipment, sometimes making this feature impossible.

The Signs indicating the need for cleaning of the column

Cleaning of the gas column should be carried out if:

• The equipment does not turn on or off;
• Constantly triggered the sensor for thermal protection;
• Decreased the efficiency of the device;
• The pressure at the outlet is quite weak.

The need for cleaning indicates that if the column some time after the beginning of the turn. In this case, you must make sure that the water and gas go inside. If you notice that constantly triggered the sensor for thermal protection, you can be sure that the inside had accumulated a thick layer of limescale, which has a porous structure and different insulating characteristics, this circumstance interferes with the normal cooling.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Cleaning of the gas column is required in the case where the decreased efficiency of the device. The water began to heat up weaker. This is true for the case when the output water pressure was quite weak, which indicates that the water simply can not break through the channels, covered with scum. Before starting any operation with the equipment, you should turn off the tap of gas supply and water.

Cleaning the water intake site

Cleaning of the gas column must be conducted in the area of the intake site. It is located at the entrance, has a mesh filter to prevent clogging of tubes of heat exchanger elements of the large particle sediment and rust. Before you clean the gas column, you must remove the intake node of the housing, and then Unscrew the connecting screws that will allow you to open the case.

You Need to clean the filter and then rinse it under a strong water pressure. The membrane should be checked, it should be flat. If it is not, and the element is concave, it indicates that the node has worn out and must be replaced. You can use a modern silicone model, which has a much larger life. After clean gas column failed, should close the lid of the intake site, screwed the screws and tighten them alternately.

Cleaning of the gas burner

Cleaning the burner of the gas column can be carried out only in the region of the nozzles. If you compare the torch with the water part, the latter you can disassemble yourself, but the first should be entrusted experts of gas service. To remove soot from the nozzle of the burner need to clean it with copper wire.

To Remove the soot can be brushed metal. The column is checked for the leak of gas, which is preparing a soap solution that can be imposed on the pipe connection and Assembly. If the junction began to form bubbles, this indicates a leak. The crane should be shut off and call the service 104. Cleaning of the gas column from the scale is not needed if time to exercise prevention. For this operation you need to use filters and try to reduce the hardness of the water used.

Possible reasons that the pilot light is extinguished in the column

If you notice that the pilot light goes out gas water heaters, it is necessary to identify the possible cause, it may be due to the fact that:

• There was a blockage of debris and dust;
• There is no draft in the chimney;
• Burnt or worn out thermocouple;
• Smoking occurs because of the lack of air;
• Is dominated by the external flow of air;
• There was a sensor fault traction control;
• Out of order solenoid valve.

One of the most common causes of the above problems is the fault of the thermocouple. It has the form elementa safety device used to shut off the flow of fuel in unstable operation of the equipment.

If the pilot light goes out, the thermocouple detects the lack of heat and turns off the gas. But if you have burned the thermocouple tip and was friable from exposure to fire may cause the above problems. Sometimes it happens so that the holes of the gas nozzle for the pilot light have a small diameter, which is why they get clogged with dust and debris, preventing normal combustion.

Device gas column

If you want to carry out cleaning of equipment, then you must know the device of the gas column. It usually consists of a metal body, which resembles a cupboard. For column summarizes pipes for water supply and fuel supply. The design assumes the presence of:

• Heat exchanger;
• Pilot burner;
• Main burners.

Depending on which method of ignition is used, after opening the faucet starts to work the valve of the column which transmits the flow of fuel to pilot burner, it ignites and the main. A fairly large amount of heat is released when burning gas.

The Heat passes through the heat exchanger, made in the form of a spiral. As soon as the water is heated to the desired temperature, is fed through the outlet pipe, and opens out to the outdoor faucet. Studying the arrangement of the gas column, you will understand that it has a chimney, which is necessary for removing the products of combustion gas from the premises.

More about the device

Depending on which igniter is used, the column can be electronic, manual or piezo ignition. The second option is obsolete, because involves the use of matches to ignite pilot light. The main column in this case is used only after be able to rotate the knob. Modern gas columns almost always have the electronic ignition, because it is characterized by ease of use, practicality and safety. Such systems can operate in automatic mode and do not require intervention on the part of man.

Conclusion

Cleaning of the gas column with their hands can be carried out in the area of the heat exchanger. To do this, disconnect the outlet and inlet water to the heat exchanger. If cleaning was carried out not so regularly, then the nuts may be clogged with scale. Thus it is necessary to use a special liquid, which you can buy at an automotive store.

Grease fitting tool is buried in the junction of the fastener. After 30 minutes the nut can easily be turned off. As soon as the heat exchanger will be disconnected, using a funnel, pour the descaling solution. Sometimes cleaning implement stem 9-percent vinegar, which is pre-diluted with water in proportion 1 to 3.