How to bend drywall for arches: a step-by-step description of effective methods and recommendations

Drywall is a versatile building material. Quite often it is used to create smooth surfaces. But becoming more common among homeowners and designers gain curved objects of the GCR, among them are:

• Multi-tiered raised ceiling;
• Arch doorways;
• Niche with curved lines.

To Create such masterpieces you can own hands. This will require tools, materials and instructions with which you can find below. Tips on how to bend drywall for an arch, will help not only finishers that almost every day dealing with drywall, but for ordinary consumers, having started repairs in the house or apartment. If you want to diversify the interior of one of the above objects, it is necessary to learn how to bend a sheet of drywall and strengthen it.

Training materials

If you pondered the question about how to bend drywall for an arch, then podgotovit:

• Samorezy;
• Ugolnik;
• Valic;
• Ruletku;
• Carandas;
• Knife with interchangeable blades;
• Sponge or sprayer.

Before beginning work, you must cut drywall to size. The operation is quite simple, this square should be placed along the sheet edges and with a knife make a deep cut. The sheet is bent along the line of cutting to break the layer of plaster. At the final stage the wizard will have to cut the paper layer on the opposite side.

It is Important to ensure before you start bending that the fragment suitable in size. To date, there are several ways that allow you to attach drywall curved shape, among them the hydration and application of parallel cuts.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

The First technology used when you need to slightly bend the blade. The second method is useful when the sheet you wish to use a greater curvature. You can use the alternative in the latter case, one uses two layers of drywall, the thickness of each of which is 6.5 mm., This material is a arched drywall as it is easier to bend. You can use a single sheet of drywall mentioned thickness and another layer of plywood with identical parameters. Before to bend drywall for an arch, you need to practice on a waste. To repeat that manipulation several times, it will allow in the future to remove errors.

Bending of the sheet through the incisions

The Cuts will allow you to bend the sheet of drywall when it is used to form door arches. In this case, to give the sheet can be an impressive radius. In order to bend the sheet, it should make incisions with a certain step, the distance between them should vary from 3 to 5 cm, the Sheet should be laid on the floor and lean him against the wall.

Using a ruler or a level on the canvas are made parallel cuts. If the paper layer is incised on one side, this will allow you quite simple to bend the leaf, leaving intact the layer of paper from the other side. In addition, it would eliminate the risk of damage to fabric. If you have a question about how to bend drywall for an arch, then to break the plaster the next step is in places cuts to the fabric was as flexible as possible. If the technology had been complied with, the drywall will Flex easily enough, this will give the fabric the desired shape.

Now to align the fragment of an arch with the plane of the wall and secure the sheet with screws. In order for the results of the work met expectations, all operations should be performed carefully. Record sheet required in increments of 5 cm to Use for this you need a screwdriver that has adjustable torque. This will allow to tighten the screws correctly and quickly.

It is Important to ensure that the metal frame is strong enough, otherwise the arch will not be as hard as I would like. If arch is not found, corresponds to the expectations, it is not necessary to do hasty conclusions. After the design is glued reinforced with wire mesh and treated with several layers of putty, it will look more attractive.

How to bend a sheet by wetting

If you want to give the drywall a curved shape, it is possible to moisten the fabric with the back surface of the sheet. In order to make the bend to the maximum, it is necessary to moisten not only the rear but also the front side. The leaves are placed on a smooth concrete floor, and moisten by using a garden sprayer or roller. If you want to wet the drywall much, you can even use a sponge. However, the excess water can damage the material, so the hydration should be gradual.

Technique works

Before you bend the piece of drywall for the arch, you have to wait for the moment when the water is absorbed into the material. It may take about an hour. To work with greater care, because a wetthe panel may be damaged. As soon as you give the sheet the desired shape, you need to check the room to get rid of excess moisture.

Wet the sheet too much is not necessary, otherwise the paper may tear. The next step is to fix one of the edges of the leaf, then the leaf should start to bend, wineva screws. It is important to be careful to get a smooth curve. The distance of the screws from each other must be equal to the limit from 10 to 15 cm, otherwise the curve will turn out wavy. Set screws should be very carefully, because otherwise you will have to spend more effort to finish leveling the surface, causing the putty.

Tips-on-wet method of bending plasterboard

A Fairly common part of the interior in recent times are the arch of plasterboard. Wet method to prepare a material for this purpose is possible by the above scheme. However, there are some nuances. For example, to a sheet soaked better, it should be treated with a spiked roller or with an awl on one side, which is concave. After you can start wetting the surface with water, to use can not only roller or spray, but brush.

The Sheet left for some time, you need to check it after 15 minutes – are the canvas for further work. It is important to exclude the time that the water soaked through the canvas. If you don't want to fix the sheet immediately, you can fix it on the template with sticky tape and leave to dry completely.

Expert advice

If you pondered the question about how to bend drywall for an arch, but the bending is supposed to be impressive, on the rear surface of the sheet necessary to make cuts through 5 see But if you bend the bending need only a little, the sheet is moistened with a roller or sponge. In the beginning it is necessary to consider the sequence of actions, it will allow to avoid errors.

Using the framework

Quite often, novice handyman are wondering about how to bend drywall for an arch. The methods of such work described in the article. For example, as one of the solutions is the use of dry method. It is suitable to create a slight bend. The curvature of the part will depend on the thickness of the material. A thinner sheet will allow you to obtain a smaller radius.

The first step is to prepare a framework that will serve as a template. This element can be made from plywood, steel or chipboard. One edge of the part is fixed to the template and slowly bend, it is important to exert a little effort, trying to give the sheet the shape of the frame. If you have wondered about how to bend drywall, you should remember that as the adjoining surface of the sheet to the template sheet should be fixed with screws. For convenience, such work should enlist the help of a partner.

Tips for DIY

If you too have wondered about how to bend drywall in the home, it is important to prepare a template, which is made of a U-shaped profile. On the side bars you need to make cuts to the base, the distance between which is equal to the limit from 30 to 70 mm. the Material is easy to bend, then giving it a desired look. If the bend needs to be directed to one side, then you need to cut the base profile and the shelf with one hand.

Conclusion

At the time the drywall has made a revolution in the field of decoration, simplifying and facilitating many of the works. Today this material is used even more widely. He learned how to make arches and different designs of curved shapes. You can also follow the experience of most using recommendations from the article.