Replacement bearing for the "Prior" with their hands

Date:

2019-06-10 20:20:23

Views:

532

Rating:

1Like 0Dislike

Share:

Table of contents:

Set pivot bearings are "priors" on the racks and usually change with them. But it happens that bearings fail much earlier – quality, not all products are perfect. With the help of this element ensures the correct functioning of the entire suspension, as well as the rotation of the wheels. If the bearings fail, there are many inconveniences which affect the drive. Independently to replace even a person who knows only superficially the design of the car.

bearing Priora

Bearing Manufacturers

You Need to select the parts before you replace the bearings on the car. On the "Prior" and "tens" are installed in a similar product. The best quality release of such companies:

  1. SKF.
  2. KOYO.
  3. SNR.

The cost of the products is very high – this is a fact. But life is more than domestic counterparts. If you want to save money, purchase domestically produced products, the cost is about 500-700 rubles apiece. It is advisable to choose parts of those firms which are recommended by AVTOVAZ. Remember that the installation of the new bearing will allow to ensure the stable operation of the suspension, permanently get rid of the chatter in the place of attachment of the strut to the body.

What you'll need for a replacement

In order to independently replace the bearing stands "priors", you need to have a minimal set of tools. Will have to dismantle the strut tower, but it is not easy. But try to identify the position of all the elements relative to each other – this will allow adjustment of camber angles in the future. You need the presence of such a tool:

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

  1. Set of keys and mechanical heads.
  2. Screwdriver.
  3. The Token.
  4. Puller for the steering ends.
  5. The Puller to the springs.

With all these tools, you can begin to repair. It is also desirable to have at hand durable steel wire. Adhering to all guidelines, you will spend repairs per hour, high spend two. It is relatively small.

car Priora

Price block bearing on "Priora" is no more than 700 rubles (if to purchase domestic products). The repair stations will cost at cost spare parts, sometimes more. Difficulties in no, then no reason to overpay just yet.

Training for repair

Before you start the repair, you need to prepare. This will make some simple manipulations:

  1. Put the machine ("Priora" or “ten”, it does not matter, the algorithm works the same on them) and on level ground.
  2. Fix the position of the car – under the rear wheels put the shoes, squeeze the handbrake and put it in first or reverse.
  3. Tear down the thread all the bolts fastening the front wheel (it is advisable to replace the bearings on both struts).
  4. Lift up the side where you plan to change the thrust bearing.
  5. Completely Remove the wheel.

At this stage of preparation can be considered complete, it is time to disassemble the suspension and replace worn parts. Note the status of all dusters – if they're damaged replace them.

bearing stand priors

Removing racks

Further work is performed according to this scheme:

  1. Remove the cotter pin from the hole in the finger tip of the tail and twisting the nut.
  2. Install the puller and remove the thumb tip, pull it to the side.
  3. Pull to the side of the brake hose.
  4. Outline with a marker the position of the knuckle relative to the strut – that's what affects the camber angle.
  5. Unscrew the nuts from the bolts attaching the strut to the knuckle and remove them.
  6. Pull down a bit the hub and the knuckle.
  7. Under the hood twisting the key on “13” three stud nuts fastening bearing "priors" to the body.

After all these steps, you can remove the whole strut Assembly, it holds nothing. Spring does not uncoil – she's still firmly “sits” on the front.

pillow block bearing price

Dismantling bearing

To remove the bearing, you must use the device for compressing the springs. The actions performed are:

  1. Install the device for three turns.
  2. Rotate the bolts evenly until the spring is compressed. No need to overdo it – enough so that the spring has weakened and the pressure on the cushion is decreased.
  3. While Holding against rotation the shaft, Unscrew the nut key on the “17”.
  4. Carefully remove the bearing.

To ensure the safety of the work, fasten a few turns of steel wire. Easier just to Unscrew the nut from the rod by means of a special key. Very often it happens that the metal strong liking, Unscrew the nut difficult.

knocks bearing Priora

Assembly

After removing the old bearing "priors" in its place install a new. Next, do the following:

  1. Spin the nut on the stock.
  2. Release the spring, and finally tighten the nut.
  3. Install the strut Assembly into its place and nailseathe nuts on the three studs.
  4. Install the steering knuckle to the strut tower the same as it was previously – focus on labels.
  5. Install the bolts and tighten the nuts on them. Please note that the upper bolt with adjusting washer fixed in the form of an eccentric.
  6. Put in place the tie rod end, tighten the nut and insert the cotter pin. Be sure to pry his mustache below when he fell.
  7. Tighten all threaded connections.
  8. Install the wheel and lower the Jack with the car.

The repair is over, likewise the work on the second rack. Nothing complicated in this, but it will take patience and the ability to work the keys. And if suddenly knocking the thrust bearing on the "Prior", you know what to do. Preferably before beginning repairs all threaded connections to handle penetrating grease type WD-40 or even brake fluid.


Article in other languages:

AR: https://tostpost.com/ar/cars/17713-replacement-bearing-for-the-prior-with-their-hands.html

BE: https://tostpost.com/be/a-tamab-l/34069-zamena-apornaga-padshypn-ka-na-priore-sva-m-rukam.html

DE: https://tostpost.com/de/autos/33749-ersatz-stehlager-auf-priority-mit-ihren-h-nden.html

ES: https://tostpost.com/es/coches/33612-la-sustituci-n-de-la-referencia-de-los-rodamientos-priore-con-sus-prop.html

HI: https://tostpost.com/hi/cars/19371-replacement-bearing-for-the-prior-with-their-hands.html

JA: https://tostpost.com/ja/cars/17385-replacement-bearing-for-the-prior-with-their-hands.html

KK: https://tostpost.com/kk/avtomobil-der/34375-auystyru-moyynt-rekt-arnal-an-priore-z-oldarymen.html

PL: https://tostpost.com/pl/samochody/35439-wymiana-o-yska-oporowego-na-priore-w-asnymi-r-kami.html

PT: https://tostpost.com/pt/carros/35224-a-substitui-o-do-mancal-de-apoio-no-priore-com-suas-pr-prias-m-os.html

TR: https://tostpost.com/tr/arabalar/30800-yedek-rs-rulman-ba-rahip-kendi-elleriyle.html

UK: https://tostpost.com/uk/avtomob-l/34602-zam-na-opornogo-p-dshipnika-na-pr-or-svo-mi-rukami.html

ZH: https://tostpost.com/zh/cars/6128-replacement-bearing-for-the-prior-with-their-hands.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

2107: setting the ignition (manual and scheme). How to set ignition VAZ 2107

2107: setting the ignition (manual and scheme). How to set ignition VAZ 2107

In this article, you will learn about how made on the 2107 installation of ignition. This car can be installed both non-contact and contact ignition system. Regardless of which design systems are installed in the car, all work is ...

A new generation of cars

A new generation of cars "Peugeot Partner": the technical characteristics and not only

“Peugeot Partner” is a compact commercial van produced by the French group «Peugeot-Citroen” in 1996. During this time, the car managed to win the European and Russian markets due to its practicality and re...

Snowmobiles Ski Doo: specifications, reviews, and photos

Snowmobiles Ski Doo: specifications, reviews, and photos

Winter – a time of miracles. Some people prefer to go skiing or sledding, but still, many commend the snowmobiles. Of course, this means of transportation is difficult to manage, especially if the person in this case a begin...

"Honda civic" 2008: owner reviews, specifications, advantages and disadvantages

Perhaps one of the most popular Asian sedans is the "Honda civic" (2008). Owner reviews left on this car, are impressive. Anyway we have to admit that a lot of people, a little bit interested in cars, know that model. So...

How to take the cars out of impound? What to do if your car was towed to the impound lot?

How to take the cars out of impound? What to do if your car was towed to the impound lot?

In recent years, an increasing number of drivers violating traffic rules and Parking. Unfortunately, in large cities and Metropolitan areas is inevitable. Most likely the final such event – the offender's car to evacuate and...

Mercedes-Benz W202: technical characteristics of the car

Mercedes-Benz W202: technical characteristics of the car

Model the Mercedes-Benz W202 replaced its predecessor, W201. Or how this car was known, 190-mu "Mercedes". The novelty is produced in the light from 1993 to 2000. And she had, you might say, great success. In all there w...