The Residue of the morning mist or evening – the phenomenon is very frequent in our climate zone. However, such weather conditions hamper safe to travel by car due to poor visibility, especially if the vehicle is not equipped with fog lights (fog). How to get rid of this problem? Quite simple – you just buy the fog light kit and install on their equipment.
Below is a detailed description of how to choose the right lighting device and how to mount them on the car for example «Lada Priora”. Installing fog lights on a “Priority” – the process is not very complicated. And work virtually every driver, even a little bit in the technique.
What you first need to pay attention to when purchasing the headlamp at the store? The integrity of the hull, diffusing filter and light bulbs, the presence of plugs of fastening of electrical wires. Special attention deserves the material of the fog light on “Priority”.
If the installation of a PTF is expected in the case of the bumper, it is necessary to clearly determine the size and shape of the part for further smooth editing. As a rule, "Prior" foglights installed in the lower part of the bumper, which has a hole for a round headlight or trapezoid.
Membership of the UNECE should be confirmed clymenum familiar with “E” on the body of the lens. Russia, Europe, and Asia – these are the main countries supplying the market elements of light equipment of the car. Option Asian manufacturers may not always conform to the standards and safety requirements, although these products and have lower price. If we talk about the examples of European manufacturers, the situation is different – a direct correspondence of price and quality. But there is one significant drawback – the size of the product. Since it is difficult to choose the right size, you may experience problems connecting. The most optimal variant –to buy new fog lights on “Priority” domestic producers. Products correspond to GOST, fit perfectly in the exterior of cars and also have reasonable price.
Recommended
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...
The Most common today are anti-fog device equipped with halogen bulbs. Their standard capacity is equal to 55 watts. Such lights form a luminous flux of 1.1 thousand lumens. This is enough for scanning ahead of the car about thirty feet, that will protect the movement.
For the installation you will need the standard tool kit, knife, insulation tape, screws. Immediately before the repair work should conduct a number of preparatory operations. The first thing to do is to disconnect the negative terminal from the battery in order to avoid later short circuits when you want to connect fog lights on “Priority”. You then dismantle the metal undertray. In the future it will not interfere to remove the bumper. This operation is quite simple – you need only to Unscrew a few bolts for protection.
The Disassembly is carried out with the help of Allen key for ten and a notched screwdriver. First, Unscrew the screws connecting the protective covers of the wheel arches with the bumper. Their total number – six pieces (three on each side). Then, Unscrew the four bolts mounting the bumper to the metal bracket transverse of the body in its upper part. Next, remove the headlight housings by loosening the four bolts on each. After these operations, the bumper a bit you can pull, which will allow you to access the three lower bolts. Unscrewing them, you can remove the bumper completely and install fog lights on a “Priority”.
If the vehicle is not previously equipped with PTF, the bumper on the landing field lights will have a plug. With a knife (if you have a jigsaw, you can use them) plugs neatly cut. It is possible that the cut edges can have burrs and roughness. In this case, they can handle round rasp or sandpaper. Then you can install fog lights on a “Priority”, and secure them with screws.
Are fastened-terminals of the headlight to the body of the car, and laid the electrical wire to connect. After this work is done mounted on the car bumper and fasten it. You can also install the underbody protection.
There is another way of equipping the car with such svetostoykimi. Fog lights on “Priority” can be mounted directly on the bumper cover. For this sale there is a certain type PTF for outdoor mounting.
The Connection lights do not take much time if you thoroughly understand the wiring of the car. To begin, set the light switchof fog light in the car on the dashboard. For this you need to open the protective cover of the steering column by turning the locks on ninety degrees. Remove the cover located to the left of the clock. Instead, mount the switch. Then connect the plug wires internal scan to enable fog lamps.
The Wiring from the switch build to the fuse block. In the case of the block in the backup set saddle K10 relay and connected the wires to its terminals. Then one wire of the switch is connected to the outlet "85". "86” – challenge for a lot of, “the thirties” – the contact device of the relay K7, and "87” – challenge to the fuses F17-18.
Next, the second cord from the switch installed on the “plus”. To free taps switch input and connected the wires from the fog lamps. Connecting fog lights on «Lada Priora” can assemble the steering column cover together and to test. It should be noted that complete data light devices is detailed instructions on connecting the lights to the car, which is practically the same for all models of VAZ.
Installing or replacing fog lights on “Priore” – half of the work done to achieve the desired result. The next and important point – set the correct direction of the luminous flux.
Is Checked, and if necessary, set the recommended pressure in the wheel tires. Then the car loaded with mass equal to the sum of the weight of the alleged passengers, and is set on a flat surface opposite the vertical wall at a distance of five meters.
Enabling PTF produced measure the distance from the ground to the center of the lens lights. Then on the wall to draw a horizontal line five inches shorter than the distance of the center of the headlight to the ground. Correct adjustment of the top face of the beam should be flush with the marked line. In case of discrepancy should be adjusted by changing the angle of the fog. Each lantern work is carried out separately. One of the bulb cover, and then compare the results.
On the Basis of the article, it's safe to say that mount fog lights on “SE Prior" or its modification without special efforts, without the help of professionals and sophisticated repair equipment.
In any weather this type of indirect lighting will always come to the aid of the driver and eliminate the probability fly off the road and into a traffic accident.
So we figured out how to install fog lights on «Lada Priora”. There is nothing complicated, the main thing – to do everything properly.
Article in other languages:
AR: https://tostpost.com/ar/cars/20296-how-to-install-fog-lights-on-priority.html
BE: https://tostpost.com/be/a-tamab-l/37961-yak-ustalyavac-prot-votumannye-fary-na-pryeru.html
DE: https://tostpost.com/de/autos/37594-wie-installiere-ich-nebelscheinwerfer-auf-priora.html
ES: https://tostpost.com/es/coches/37356-c-mo-instalar-los-faros-antiniebla-en-la-prioru.html
HI: https://tostpost.com/hi/cars/22001-how-to-install-fog-lights-on-priority.html
JA: https://tostpost.com/ja/cars/19955-how-to-install-fog-lights-on-priority.html
KK: https://tostpost.com/kk/avtomobil-der/38367-alay-t-man-a-arsy-faralar-arnal-an-prioru.html
PL: https://tostpost.com/pl/samochody/39898-jak-ustawi-wiat-a-przeciwmgielne-na-prioru.html
PT: https://tostpost.com/pt/carros/39545-como-instalar-far-is-de-nevoeiro-no-prioru.html
TR: https://tostpost.com/tr/arabalar/34839-nas-l-y-klemek-i-in-sis-farlar-prioru.html
UK: https://tostpost.com/uk/avtomob-l/38769-yak-vstanoviti-protitumann-fari-na-pr-oru.html
ZH: https://tostpost.com/zh/cars/30554-how-to-install-fog-lights-on-priority.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
"IZH 350 Planeta Sport" – frisky Soviet bike
it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...
Toyota Verossa ("Toyota Verossa"): specifications and owner reviews
Toyota in the early twentieth century was at the peak of popularity in the country. In Japan in those days, the demand for cheap and large sedans under the hood which was hiding powerful engines. Models such as the Toyota Verossa,...
Car GSM beacon: popular, purpose
Autonomous GSM beacon today is a fashionable trend in the protection of vehicles against theft. The market has a large selection of these devices. A small price determines the success among motorists. But how this protection will ...
Dump truck "Khovo": specifications, owner reviews, photos
the Truck ‘Khovo” today is one of the most popular brands of cars of its type on the market of Russia and other CIS countries. In the first place, so its popularity is due to the fact that it's considered quite cheap c...
"Lada 4x4 urban": technical characteristics, description, photos
the Car «Lada urban 4x4" of the specifications which we will explain in detail in the article, announced two years ago, “AVTOVAZ” like a real new domestic SUV, made on the basis of all known «the Field...
Luxgen 7 SUV: owner reviews, specifications, photo, country-producer
Luxgen 7 SUV – is the name of a mid-size crossover manufactured by the Taiwanese car company. The first thing I would like to mention the fact that this is – the first car company in the Russian Federation. Start its s...
Comments (0)
This article has no comment, be the first!