The installation of sensors on the "Kalina": with his hands

One HUNDRED Many advertise their services on the installation of the PDC, but it is expensive. Installing sensors on «Kalina» can also be performed and independently – a simple process and if certain skills installation can be done very carefully.

How the system of safe Parking

A Special electronic unit receives information from the sensor, and then notifies the driver about the obstacle. Sensors are the main devices in the system. Thanks to these small devices running on ultrasonic technology, the sensors can detect obstacles. The radar is Also equipped with a display or indicator light to alert the driver. In addition to display, many devices have a function of sound notification. Parking radar, LCD displays enable the driver to obtain more detailed information. Some models may be equipped with a rear view camera. Among the models there are and such, where information is projected onto the windshield of the car.

Contents

So, the device has already been selected and purchased – depending on the cost and manufacturer it can be differently equipped. So, manufacturers from China are often Packed Parking radars in simple plastic bags, while more serious brands from Europe and USA to deliver their products in beautiful boxes with a set of fasteners. It also includes installation instructions. Included with the device are the sensors in quantities of 2 or more – often the device is offered with four. Also there is the control unit, the display or indicator connecting wire (if wired sensors). Included in the kit and a cutter for drilling holes in the bumper of the car. Some manufacturers also add in a set of double-sided tape – it can be used in the installation process.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Painting of sensors

The Installation of parktronikov on «Kalina» your own hands begins with the preparation of sensors – often the cars “choice” bumpers are painted in body color. Sensors Parking radar, regardless of price and manufacturer, not painted or made in a different color. After installation not to damage the exterior of the machine, the sensors must be painted. For staining you can use spray cans. The advantages of this solution is the easy selection of the desired color. The drawback is that using the spray pollen falls on other elements of the device, where their presence is undesirable. Much easier, faster and safer to painting brush for glossing over chips on the body. Technology painting special recommendations. But to have these items look perfect and not stand out of the bumper should be painted in two layers. If you use a brush, the layer will get slightly thicker. The paint will pucker. To avoid this, you need to try to make the layer as thin as possible. Then paint on allow to dry and re-applied. Of course, the ideal coloring in this case difficult to achieve. But it's better than just black holes in the bumper.

Marking of work

Setting the PDC on «Kalina» your own hands is a simple task that even a novice. However, in this operation there is one problem – it is the markup of the rear or front bumper under the holes for the sensors. Here you need to correctly calculate all the parameters. The height, width and space, where there will be extreme details. There are many opinions and different information. So, if you look at the reflective elements, the sensors at the edges of the bumper must be installed inside the structure at 2 cm, above the reflectors. And generally they are placed anywhere. But you do not need. The closer to the edges of the bumper, you will install PDC on «Kalina», the better – such approach will allow to increase the range of the sensors on the sides of the car. If you look at any foreign cars, and there these items are installed around the perimeter. The maximum configuration of "Lada Kalina" has regular sensors – it is equipped with three ultrasonic sensors. In this case, the manufacturer installed an extreme controller 10 cm in the direction of the reflectors. Note that the system will work effectively in that case, if the elements are installed parallel to the ground.

Install Parking radar on "Lada Kalina" in the back of the wagon

Setting the PDC on «Kalina» universal can be done in the following way. You can install sensors on the same line in the middle of svatovavrinecke. And extreme elements sets of 3-4 cm from the edges, and the other is mounted 40-45 cm Professionals suggest to mark the holes on the masking tape – directly to the surface of the bumper stick tape, and it has been drawing linesand do labels. Then using any sufficiently sharp object mark the places already on the plastic bumper.

To Remove or not to remove the bumper

There are also two options. Installing sensors on «Kalina» can be done without removing the bumper – the wire attackyou will reach out with a wire. Many believe this technology is too costly in terms of effort and prefer to dismantle the bumper. For dismantling for «Kalina» Unscrew the bolts on top and bottom. Also Unscrew the fenders and then the bumper can be easily removed. Then it is recommended to lay it on a flat surface – it will be easier in the process of drilling.

How to make holes for sensors

Producers complement Parktronic crowns that using a drill or screwdriver can drill neat holes.

Professionals recommend for those who install Parking sensors with your hands (Kalina or any other car) - the first serious tuning, don't run at high rpm. The rush will not lead to anything good. Holes need drilling maximum slowly – then you can achieve perfect results.

High speed drilling will cause heating of the crown – plastic bumper can melt. This will significantly complicate the process of pulling the crown. Also reduced the edge of the hole. In this case, you will have to modify them with a file. On the car «Kalina» installation of sensors will be done carefully, if drilling slowly and give the crown to cool before the next drilling.

Installation of sensors

Next, when holes are ready, you can begin the installation of sensors. On the reverse side on each sensor contains a label and an additional UP arrow. These labels should Orient the sensor in the hole. Then he is fixed with latches. Producers complement of sensors of different types. In case the fasteners with silicone, have to bring them with a screwdriver. Do equipment in China.

When the sensors are installed, please purchase the site for installation of ties – they can be found in any hardware store. The surface should be thoroughly cleaned and degreased – platforms on the double-sided tape attached between the sensors. Next, the wire going to one harness, and at the end they wear a groove and brought into the cargo compartment through the hole under the left tail light After that, the bumper can be installed in its rightful place.

Connect

Then the two wires connected to the reversing light. To do this, we have to wrap the trim in the trunk. To connect wires you can use scotchloks. To the rear lamp connect plus and minus. The control unit is connected according to the instructions and fit somewhere in the trunk. So you are installing PDC («Kalina» the universal is no exception). It remains only to assemble, turn on the ignition, put the gearshift lever into reverse gear and to check whether an installed device. Also it is necessary to connect and attach the display or indicator. Then you can use sensors on the vehicle “choice”. The installation of sensors, as you can see – is really a simple operation. With her easy to handle even novice motorists.