Rear hub is designed to connect the movable wheel and the suspension member – the beam. The design of the hub can be compared to a small Cup made of metal. In the inner part of pressed special design bearing. A very simple device, but it can bring a lot of trouble to the motorist – wear in the bearings begins to buzz. But if not timely replacement, the bulbs can and does jam, which will result in wheel lock-up and sudden stop of the machine – when riding at high speeds this will lead to a crash.
Very different rear hub 2108 from a similar mechanism used in automobiles “classic” series – VAZ 2101-2107. The design of the rear suspension on FWD cars is pretty simple. On the beam is a mount axis, it is somewhat similar to the knuckle, installed on the front axle. But one difference – this element can move in a vertical plane but rotate does not work – fixture hard.
The hub is a small metal cylinder, hollow inside. It is pressed on a clip – special bearing, which is produced by the rotation of the wheel on the axle shaft. Moreover, the outer diameter of this bearing is same as the inside of the hub. And the diameter of the inner race the same as the outer from the axle shaft. Consequently, the fit of the hub on the axle is the most dense, no gap there. This can be understood only once parsed element.
Recommended
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...
In the mechanism of the rear hub 2108 often fails is the bearing – the most vulnerable place. But sometimes there are more specific breakdowns – cracks on the metal surface of the hub, the destruction of thread for the wheel bolts. In the second case, you can not completely change the hub, enough to cut a new thread. But this is not always helps, it is easier to buy the new one. Therefore, if the bolts they rotated on the thread, you need to immediately start the repair, otherwise it may end up that you lose the wheel.
In the case when the bearing wears out, there are strange sounds – a strong buzz increases with speed. The reasons may be several:
In any case required to carry out the replacement item. Once the drone reaches its maximum, will begin to receive vibrations – and the greater the wear, the more it will be.
Before to change the rear hub or the bearing, make sure that you have all the necessary tools. Without special pullers to do the dismantling of the bearing is unlikely to succeed. If you are planning to put a new hub Assembly, then no problem – it already has a new bearing that is installed according to the rules.
But if you buy all the elements separately, the presence of the puller is highly desirable. You need to have on hand the following tools:
This all, also you will need a new bearing and hub nut. Old re-use is not recommended.
The Price of a hub Assembly for VAZ-2108 and similar models is about 1200 rubles. The bearing will cost about 350-600 rubles (depending on the manufacturer and the greed of the seller). The results show good some foreign manufacturers of bearings, but if you want quality and low price, please pay attention to domestic – Vologda and Samara. First be much better, service life is high. But you need to buy the parts only from trusted sellers – to the aftermarket a lot of Chinese goods, the quality of which leaves much to be desired.
To dismantle the rear hub on VAZ-2108 or any other car with front-wheel drive, you must perform preparatory work:
Now we need to raise the repaired side of the car and begin to dismantle the hub.
To disassemble the rear hub, you need to perform such manipulations are:
That's all, now you can put a new rear hub Assembly. But if you need to replace only the bearing, it is necessary to dismantle the old and replace the new.
In order to remove the bearing, you will need:
After all these manipulations assemble the whole site. Tightening the wheel nut, bend the ribs so it does not Unscrew.
Article in other languages:
AR: https://tostpost.com/ar/cars/14901-hub-rear-features-and-instructions-for-replacing.html
BE: https://tostpost.com/be/a-tamab-l/26665-stupica-zadnyaya-funkcy-nstrukcyya-pa-zamene.html
DE: https://tostpost.com/de/autos/26753-nabe-hinten-die-funktionen-und-anleitung-zum-austausch.html
HI: https://tostpost.com/hi/cars/14919-hub-rear-features-and-instructions-for-replacing.html
JA: https://tostpost.com/ja/cars/14927-hub-rear-features-and-instructions-for-replacing.html
PL: https://tostpost.com/pl/samochody/26473-piasta-tylna-funkcje-i-instrukcje-dotycz-ce-wymiany.html
PT: https://tostpost.com/pt/carros/26484-cubo-traseiro-fun-es-e-instru-es-de-substitui-o.html
TR: https://tostpost.com/tr/arabalar/26553-porya-arka-zellikleri-ve-talimatlar-yerine.html
UK: https://tostpost.com/uk/avtomob-l/26530-stupicya-zadnya-funkc-ta-nstrukc-ya-po-zam-n.html
ZH: https://tostpost.com/zh/cars/15382-hub-rear-features-and-instructions-for-replacing.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
"IZH 350 Planeta Sport" – frisky Soviet bike
it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...
Starter - what is that part of the vehicle?
Every experienced driver knows that the starter – this device initial startup of the engine, without which to start the motor, to put it mildly, very difficult (but not impossible). It is this element allows you to create an...
Mercedes-Benz W116: description, specifications, model years
60 years were significant for Western Europe because the country has finally recovered from the economic consequences of the Second world war. Automobile manufacturers have begun developing new models. Among them, of course, and M...
At the beginning of this year, brad “shomi” presented at the automobile market combined Registrar, Sho-Me Slim Combo. The gadget is easy to deal with shooting in Full HD resolution plus, working with navigation on the ...
Tuning "Volvo XC90" how to improve auto?
the Most significant tuning “Volvo XC90” which launched in 2006, affected the appearance of the machine. This is due to the fact that the standard exterior Swedish car rather monotonous and boring. The updated version ...
What is the gasoline consumption per 100 km at different vehicles
a Car today has become an integral part of the modern man, thanks to which is possible during the working day to have time to visit many places and to solve important business issues. However, four-wheel friend needs timely ...
Comments (0)
This article has no comment, be the first!