How to tune the hood with your hands?

Date:

2020-02-07 19:00:13

Views:

556

Rating:

1Like 0Dislike

Share:

Table of contents:

Appearance of domestic cars, and some cars is not attractive and stylish, so many motorists wish to give a spectacular appearance with your own hands. There are numerous ways that allows you to select a car from millions. External changes better to start with the tuning of the hood. This is the first thing that catches the eye. In addition, hood – this is the largest flat body part of the vehicle.

Tuning gills

These items can give the car a more sporty and aggressive appearance. tuning hoodThis upgrade is very popular among all those who want to be different. For manufacturing these accessories need to have a set of tools and also room. This may be the garage.

Required tools

For production need welding inverter or any other device, sandpaper of different grit for grinding wheel, screwdriver, and grinder. As for the materials, purchase the paint, primer, putty and auto body shops of iron – for this tuning the hood is better to buy the same hood. Automotive paint is quite toxic, so best to work in a respirator.

Manufacturing Process

Form of gills or air intakes can be any – it all depends on the imagination and from the project. In garage conditions it is much easier to make gills in the form of a trapezoid. They are easier to cut, and they look very impressive. Before cutting the hood, it is necessary to mark it. Then using the grinder carefully cut out the marked border. Cut it carefully so as not to hurt the reinforcements of the hood.

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Next, after the incision, the intake set at an angle. Best of all, this tuning hood looks, if gills are to be installed at an angle not more than 45 degrees. Then from this hood from another car cut out pieces that will complement the cut of the hole. For fastening elements used semi-automatic welding, it is necessary to be very careful. Cooking need with pauses – at this time the joints must be wet to cool the cold water. tuning hood VAZNext, when the metal base is ready, you need to give it a final shape. To do this, all places and welds carefully sanded with orbital sander. Especially carefully it is necessary to handle a variety of bumps and seams – even with very careful work, these defects will arise.

As for the putty, the professionals recommend to purchase the part with an aluminum additive – this is considered to be one of the most soft and more suited to this task. When the plaster covered the entire part after it thoroughly dries, you can start painting works. After painting you can glue the hood vinyl film. We'll talk about that below.

Sticky vinyl film

This is another most popular tuning hood with his hands. Vinyl can look very impressive. Very beautiful appearance, if you choose the option print. There are many versions of these films. You can find a large choice of colours with glossy or matte texture of the carbon film. The latter is very popular among owners of domestic cars.tuning hood with their handsAll of these options differ in cost and also in characteristics. Most car owners choose a film with imitation carbon. The process of gluing can be performed independently. For this you will need a special spatula. It is important that the spatula was a soft tip. You will also need a heat gun (home will not work for this tuning), masking tape, a tube of superglue, soap, and white spirit.

The Process of gluing

Before you do the tuning of the hood, the film needs some time to lie down – leave the room for a few hours. hood deflector tuningIt is Important that the temperature in the room was room. But to sit around two to three hours will not work-yet the film rests, carefully wash the surface of the hood, and then degreased surface. After that, cut a wide piece of the prepared films. In the middle of it is fixed, and the process of pasting will go from the middle to the edge. The work will be faster and neater if you do it will be two people. One is to heat the coating with a Hairdryer, the other will flatten and remove bubbles.

Deflector

Tuning the deflector on the hood – it's not just the element to impart a spectacular appearance. This item also has safety features. Sometimes this element is indispensable for upgrades. A deflector, or "fly swatter" is made from a special perforated plastic material that perfectly withstands low temperature, do not change their geometry under the influence of direct sunlight. hood tuning 2109This element is Installed on the vehicle is very simple – just need to buy in a store favorite option. The deflector is mounted on the standard fixing points of the bumper. There are deflectors that are designed for mounting on the hood. These elements are made of a softer plastic, and plate them thinner. If you install the deflector andthen hang the hood vinyl wrap, the car will look very unusual. The hood will be protected from corrosion and dirt.

Tuning VAZ classic

In the classical models of AVTOVAZ, the majority of owners agree one disadvantage of this model series – this inconvenience in the operation of the hood. The holder is made so that the process of opening and closing is really uncomfortable. It is first necessary to withdraw the hood from the locking mechanism. In the end, you have to make a lot of unnecessary movements that really upset the owners of the classics. Many decided on the tuning hood VAZ – the issue of convenience, the hood can be solved by setting the stops from the back door of VAZ 2111. This element has a sufficient length, and due to this, the hood will open very wide. But to install you will have to make an effort – the installation process inconvenient.

As an alternative solution there is another option – the emphasis from the back door “eight”. He's shorter length. And that means you'll need a special adapter plate for mounting to the extreme point. To manufacture this plate from steel sheet of thickness 2 mm. from the Bottom it is attached with screws. But then when you close the emphasis will be to break regular locks. Therefore, the first latch bent from the edges.

“the bed-battle” for “nine”

This kind of tuning hood 2109 today is very popular. This hood will give is apparently quite normal the car an aggressive and serious look. For the process will need another hood – it can be easy to find on disassembly. tuning hood 2109So, the first thing out of a metal sheet cut out two triangular pieces. They should carefully handle – they have to be strictly symmetrical. Then they are fixed to the base with screws. When the welder welded the pieces and screws are removed. Welds need to be processed carefully. Grinder to carefully smooth the surface. It then runs putty with carbon fiber. When the surface has dried, sanded everything, then primed and painted. After drying, the paint job is finished.

Here's how you can transform the exterior of the hood, tuning 2109 allows you to come up with other options. Those cars that you can tune and change almost beyond recognition.


Article in other languages:

AR: https://tostpost.com/ar/cars/18944-how-to-tune-the-hood-with-your-hands.html

BE: https://tostpost.com/be/a-tamab-l/30345-yak-zrab-c-cyun-ng-kapota-sva-m-rukam.html

DE: https://tostpost.com/de/autos/30359-wie-man-tuning-motorhaube-mit-ihren-h-nden.html

ES: https://tostpost.com/es/coches/30390-como-hacer-el-tuning-de-la-campana-con-sus-propias-manos.html

HI: https://tostpost.com/hi/cars/17004-how-to-tune-the-hood-with-your-hands.html

JA: https://tostpost.com/ja/cars/19146-how-to-tune-the-hood-with-your-hands.html

KK: https://tostpost.com/kk/avtomobil-der/30306-alay-tyuning-kapot-z-oldarymen.html

PL: https://tostpost.com/pl/samochody/30185-jak-zrobi-tuning-maski-w-asnymi-r-kami.html

PT: https://tostpost.com/pt/carros/30209-como-fazer-tuning-cap-com-suas-pr-prias-m-os.html

TR: https://tostpost.com/tr/arabalar/34158-nas-l-tuning-kaporta-elleriyle.html

UK: https://tostpost.com/uk/avtomob-l/30284-yak-zrobiti-tyun-ng-kapota-svo-mi-rukami.html

ZH: https://tostpost.com/zh/cars/16698-how-to-tune-the-hood-with-your-hands.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

Engine

Engine "Daewoo Matiz", design and features

three-cylinder petrol engine “Daewoo Matiz” series F8CV is a licensed and modified version of the motor "Suzuki" created in the early 90-ies to equip compact cars company. Version «Mercedes» motor...

Hub rear: features and instructions for replacing

Hub rear: features and instructions for replacing

Rear hub is designed to connect the movable wheel and the suspension member – the beam. The design of the hub can be compared to a small Cup made of metal. In the inner part of pressed special design bearing. A very simple d...

Starter - what is that part of the vehicle?

Starter - what is that part of the vehicle?

Every experienced driver knows that the starter – this device initial startup of the engine, without which to start the motor, to put it mildly, very difficult (but not impossible). It is this element allows you to create an...

Mercedes-Benz W116: description, specifications, model years

Mercedes-Benz W116: description, specifications, model years

60 years were significant for Western Europe because the country has finally recovered from the economic consequences of the Second world war. Automobile manufacturers have begun developing new models. Among them, of course, and M...

DVR with radar detector Sho-Me Slim Signature Combo: reviews, overview, specifications, characteristics

DVR with radar detector Sho-Me Slim Signature Combo: reviews, overview, specifications, characteristics

At the beginning of this year, brad “shomi” presented at the automobile market combined Registrar, Sho-Me Slim Combo. The gadget is easy to deal with shooting in Full HD resolution plus, working with navigation on the ...