Heating element for washing machine: replacement. How to remove the heater from the washing machine?

As you know, the modern models of washing machines connect only to cold water. In the process of washing it is heated to the desired temperature with the built-in heating element. Therefore, the heater for the washing machine is of great importance. If this part fails, disturbed the efficiency of the entire apparatus.

If you have some knowledge to repair the heating element you can own. You need to know how to remove the heater from the washing machine and to replace correctly.

Common causes out of order heating element

Heating element for washing machines is fundamental, so it is important to know why often this part fails and how to prevent its breaking.

1. Operating Conditions. In the process heater constantly heats and cools, it eventually leads to wear of the inner spirals and conducts to failure.
2. Hard water. The heating element is in constant contact with water. Poor its composition leads to the formation of scale on the tubes. This causes the heater to spend more energy on heating water to the required temperature. To prevent the formation of scale, the experts recommend to install water filters on the inlet hose, use the special tool together with the powder in the wash. You can also periodically run a dummy cycle, i.e. without linen, with the use of citric acid or of compounds containing them.

Where is it located?

Since the heater for the washing machine is the only heating element for greater efficiency it is at the bottom of the tank. But which side of the device – the rear or the front, depends on the brand and model. Therefore, replacement of PETN washing machine starts with determining its location. This can be done in appearance of the apparatus. If the rear wall of the washing machine is large, then most likely, the heating element finds for her. In any case, the rear protective portion to remove much easier than the front, so you should start there.

Recommended

IPTV settings "Rostelecom". IPTV channels

Analog TV is gradually disappearing into the background. His place faster pace is a free IPTV Rostelecom. And it's really convenient, because digital channels to look better because of better picture, sound. But first you need to clarify some points....

IMEI: how to change the phone yourself

If you need to change the IMEI on your phone, this article will provide complete and correct information about what is IMEI code, what is it for, and how to change it.What is IMEI you May have already encountered this concept, then you know that the ...

Washing machine Bosch MAXX 4: operating instructions

All well-known manufacturer of Bosh, before you present to the world another new, not only conducts many tests, but uses all available methods to ensure maximum safety. To washing machine MAXX 4 pleased his master as long as possible, the set to her ...

How to replace heating element through the rear lid?

1. Disconnect the washing machine from the power source.
2. Drain the tank of all the water (saddle this is possible through the emergency filter).
3. Expand the device, opening access to the rear protective cover.
4. Remove the rear panel by unscrewing the bolts or screws in which it is held.
5. Protective cover is the casing of the tank, underneath it is a part of Ten. The main part of the heater element for contact with water is in the tank.
6. To remove the heater, you first need to remove the terminals with wires.
7. Next you should Unscrew the center nut of the heating element with a tubular spanner or key.
8. It is necessary to Loosen until the nut will not be with the pin in the same plane.
9. After using a screwdriver or the handle of the hammer stud is squeezed out by pressing on it.
10. You can Now remove yourself the heating element. But remember that he put on the rubber gasket. Therefore, in order to get it, may need a flat screwdriver.
11. If the new heater for the washing machine already purchased, it can be put in place of the broken device. It is inserted into the hole in the same way as you installed the old – straight, tight, straight.
12. Screwed On the stud and tightened the nut available.
13. To the installed device connects the terminals.
14. Attached back protective wall of the washing machine.

This is the simplest option of replacing the heating element. It is much harder to make it through the front side. For example, if the washing machine "Samsung", replacement heating element is made through the front cover.

How to replace the heating element through the front cover?

If you have any question on how to remove the heater from the washing machine "Samsung" or "BOSH", it can be noted that the extraction process of the device is the same as was described in the instructions above. The only difference is how to reach it. To do this:

1. Same as in the first case: disconnect the unit from power, drain the remaining water from the tank and to release access to the front of the machine and to the rear.
2. Remove the top protective cover. This will remove the two bolts from the back side and remove it from the front clips.
3. To Get the tray for the detergent.
4. Remove the bolts that hold the control panel and also remove it from the clips. To work, be careful not to tear off the numerous wires leading to the unit programs.
5. Open the hatch, remove the clamp holding the cuff and the sealing rubber.
6. Remove the screws that hold the main front protective cover, it is removed from the retainers (given back a little and down).

Now the access to the heating element is opened. It remains a disconnect in the same way as described in the instructions above, to prevent the tank (to remove the scum or extraneous small objects) and set the new heater in place.

Whereto purchase a new heating element for washing machine?

If you plan to make a self-replacement of defective item, it is best to purchase parts for repair of household appliances in specialised stores. There are skilled salespeople will help you choose a suitable variant of the device.

Do Not buy components at low prices through various message boards. The quality of these items cannot be checked properly. At worst, they can cause damage to other elements of the device.

Conclusion

If your washing machine has stopped heating the water, it is likely that, failed heating element. To make the change independently, without the help of the wizard. The main thing - to adhere to the sequence of actions and to choose the right new heating element that will fit the models of washing machine.