Installation of roof of corrugated Board: a sequence of actions and procedure
Table of contents:
Corrugated sheet for arrangement of the roof in our time is used very often, as this material is quite durable, lightweight and resistant to atmospheric influences. But in any case the installation of the roof of corrugated Board it is necessary to produce correctly and carefully. Although it does not cause difficulties.
First, you need to purchase a quality roofing material. It should not have any chips, scratches or other defects and damage. It is also necessary to make measurement of the roof to know what length should be the roofing sheets. Of course, you must take into account the fact that the bottom leaves should be slightly. In order to calculate the number of corrugated sheets, you need the length of the cornice of the structure divided by the useful width of the sheet of roofing material, and the resulting value is rounded upward.
Before you make the installation of the roof of corrugated Board, it is necessary to arrange waterproofing and roof ventilation. Waterproofing is provided by a special film that prevents the ingress of moisture into the roof structure. Lay the film should be from the highest point (ridge) overlap. Attached film using staples or rivets to the rafters.
To ensure that the roof had good ventilation, it is necessary to waterproofing to beat a special bracket, which will provide free space between the roofing and waterproofing. Further, the ventilation element is equipped on the ridge, where fresh air enters under the roof.
The Coverage may not just lie in the attic, so the installation of the roof of corrugated Board provides for the arrangement of the sheathing, the thickness of which depends on the parameters of the coating sheet. It should be borne in mind that the cornice Board must have a maximum thickness, since it mounted the very first leaves. The selected material for sheathing should be fixed to rafters with galvanized nails that are less prone to corrosion.
Recommended
The most effective methods of seed germination
Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...
Retro-reflective paint. The scope of
When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...
How to make icon with your own hands - options izgotovleniya (simple and complex)
In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...
If the installation of the roof of corrugated Board involves the use of additional support bars, they must be installed together with the crate.
The technology of installation of roof of corrugated Board is quite easy. The first sheets of material nazhivljajut from left to right or Vice versa. It should be very careful to move around the crate and on baited leaves. Stacked sheets so that antiepilepsy groove of one of the sheets was covered with the next sheet. Only after laying the 2 sheets is made final consolidation.
Also the instructions for installation of roof of corrugated Board involves laying tiles on the eaves line with a projection.
Mount the material by screws or screws, which must be the special rubber seals preventing the penetration of moisture under the roof and damage to the corrugated sheet. Tighten the screws should not be.
Last installed thing. Thus between the strip and the ridge need to put the sealer. If you need a bracket installed on the ridge of the mechanical elements.
Note that when working with the corrugated sheet to maintain the tilt angle from 14 degrees to 20.
If the material should be cut, it is better to do it with a pair of scissors for cutting metal.
Article in other languages:
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
Dressing table - the female furniture
The women's furniture in our homes – dressing table. This invention for three centuries and there he, along with the boudoir. As it did not want every woman to have a boudoir, but this possibility is not given to everyone. B...
What are the criteria to choose the front door for a country house
Saying that our home should be our fortress is especially actual in our days. More and more people trying to isolate themselves from the outside world using the input metal doors. They are not only separated living space for peopl...
Pets requires from owners a lot of responsibility, no less than the education of the child. In this case, strict adherence to the rules and regulations for the breeding of Pets. The most important thing is to create conditions as ...
How to plant Aster seedlings and get a great flower garden?
the First of September nearly all the yards bloom with asters is a favorite “school” flower. It is easy to conclude that it refers to plants that bloom in the autumn. However, there are varieties that begin to delight ...
The house of aerated concrete: pros and cons of building
many would like to build a house with his own hands, and sometimes the dream remains a dream due to the lack of the ability to implement it. It can be financial difficulties, psychological inhibitions, and there are people who sim...
Electrical wiring in the kitchen. Placement of sockets and switches
the wiring in the kitchen — one of the most important phases of electrical work in the apartment. It is in this building usually is a big part used in home appliances. And, therefore, perform wiring electricians in the kitch...
Comments (0)
This article has no comment, be the first!