When caring for your land owners are constantly faced with the problem of disposing of branches and other waste that is definitely collected after harvesting the garden. They need to either take out, or burn. Otherwise, the yard will soon appear bulky piles of garbage. Another option – garden shredder, which will cut down such waste into small pieces. It can be purchased in the store. But it costs dearly. Even used will cost about 50 thousand rubles. So much cheaper to collect deport their hands.
To understand how the chopper, you need to consider what it consists of. Device separate shown in the drawing below.
The Foundation is chipping-crushing machinery. It consists of a chipper disc, on which there are radial knives. There is also a rotor with blades and hammers. The disk rotates due to the connection with the shaft, which in turn is mounted in roller bearings. Through hopper, the wood gets to the knives. The cut part falls down to the hammers that have large crushed chips. Due to rotation forms a centrifugal force. Under its influence the chips fall on the sieve and is discharged through the discharge hole.
Existing drawings of separate differ in some specific details. But the concept does not change. As the details may vary, the size of some of them have to be customized at build time.
Manufacturer separate with their hands begins with the preparation of a metal disc (with a thickness of 1.6-2.0 cm and a diameter of 35-40 cm). It will be the flywheel. And at the same time, it will be fixed knives. In the center of the disc to make the holes for the pins. Perimeter should be symmetrical slits, which will be given chips.
Recommended
The most effective methods of seed germination
Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...
Retro-reflective paint. The scope of
When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...
How to make icon with your own hands - options izgotovleniya (simple and complex)
In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...
On one side of the disk are mounted knives. To do this, prepare the holes in which are inserted the bolts with countersunk heads. It is advisable to take the hex bolts. They better keep the design.
On the reverse side of the disc is welded a cross bar. During rotation they will push chips.
The Second step in the manufacture of separate their hands is the preparation of the body. For this purpose, a metal sheet with a thickness of 3-5 mm. from it, cut two parts, resembling the Union of a circle and a square. Moreover, the diameter of the circle should be 3-5 cm larger than the diameter of the disc knives.
The bottom plate is welded to a curved metal strip, which will serve as a sidewall. On the inner side, observing the gaps between the housing and the disk welded to the barrels (the pieces of the rod). In the barrels is threaded. They will then twist the cover. In the cap make attaching, positioning similar barrels. Also made the hole for the shaft that will be attached to the disk knives.
The cover is cut out a window where will be laid branches. It have to do with the angle that the wood is not flying back.
The Frame is handmade separate are made of metal profile (or area) with sides at least 5 cm Going in accordance with the drawing presented in the figure above.
For engine mounting is the hinged platform. For this purpose, the metal sheet thickness of 2 cm.
To build separate with your hands still need a lot of hammers. They should be the same. And to manufacture them take a metal plate of a thickness of 0.5 cm Sieve is performed in a metal cylinder with a diameter of 35 cm For the sheet metal with a length of about 100-110 cm curve, and on the surface of the punch (not drill) holes with diameter 1.0-1.2 cm
The Rotating elements must be closed by a protective cover. For it take a metal thickness 0,8-1,2 cm as stiffeners install metal corners.
On the frame is installed the lower part of the casing and the shaft Assembly. Check that the shaft does not touch the frame during rotation. If no touch, closes the upper part of the casing. If the rotation friction on the cover no, you can install the engine and slip the belts on. Adjusting belt tension, check operation of the installation at idle. Vibration should not be. If any extraneous noise, vibration and percussions not, then assembled DIY separes ready, and it can be used for its intended purpose.
Article in other languages:
BE: https://tostpost.com/be/hatn-tul-nasc/14993-vyrablyaem-scheporez-sva-m-rukam.html
DE: https://tostpost.com/de/gem-tlichkeit/15002-fertigen-scheporez-mit-ihren-h-nden.html
ES: https://tostpost.com/es/la-comodidad-del-hogar/15011-fabricamos-scheporez-con-sus-manos.html
KK: https://tostpost.com/kk/domashniy-uyut/14995-b-z-scheporez-z-olymen.html
PL: https://tostpost.com/pl/komfort-domu/14991-wykonujemy-scheporez-w-asnymi-r-kami.html
PT: https://tostpost.com/pt/o-aconchego-do-lar/14986-fabricamos-scheporez-de-suas-m-os.html
TR: https://tostpost.com/tr/domashniy-uyut/14999-mal-scheporez-kendi-elleriyle.html
UK: https://tostpost.com/uk/domashn-y-zatishok/14996-vigotovlya-mo-scheporez-svo-mi-rukami.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
What is a windproof membrane? Description, types
During the construction of a new house or repair the already finished buildings all owners pay special attention to hydro - and thermal insulation of all surfaces. At this stage, many choose the most expensive and high quality mat...
Often, but not always a welcome guest in your garden is Oxalis carob – one of the representatives of the same kind of family sorrel. Has excellent decorativeness and durability, a small plant has incredible vitality, but bec...
Flush faucets for acrylic baths: an overview, description, models and reviews
the Soviet days are long gone and then the Queen of the bathroom-cast iron bath has his throne. A few options could not settle down, but recently humanity has taken a step forward in comfortable and functional plumbing. Today, mor...
Well-septic tank with their hands: a description of the device
Almost none of the suburban area today can not do without sewer, water and heating system. The sump is quite uncomfortable as designs for sewage. They are out of date, but the purchase septic tanks are quite costly, and therefore ...
Features sharpening ceramic knives
any kitchen knife will be one of the most important tools. But in the process use it sooner or later becomes blunt. And if the standard model is clear, the sharpening of ceramic knives causing issues. Is it possible to do at home?...
Bathroom design modern design ideas big and small bathroom
Bathroom – this is the room in which the owners resemble the remnants of sleep, tune in a working mood and indulge in relaxation after a busy day. Everything must be harmonious and beautiful. That is why you should carefully...
Comments (0)
This article has no comment, be the first!