Why burn out the led bulb? Which led bulb is best?

Led bulbs — modern equipment that appeared on the domestic market relatively recently. Cost LED devices are quite expensive. But they are usually much longer than ordinary incandescent bulbs. Equipment LED is actually quite reliable. But unfortunately, sometimes it happens so that the LED device begins to blink or even completely fails. Why burn out led lamps — will deal with this later in the article.

Main causes of failure

Burn the led bulb maybe:

• Wiring fault in the house;

• Malfunction of the lamp or chandelier;

• Low quality Assembly.

Wiring

Very often, the owners of houses and apartments are interested why led bulbs burn out constantly. The reason in this case, most likely lies in the wiring. In order to resolve this problem, you should call the management and call the electricians. The experts will check the network and will eliminate all the problems.

Of Course, you can inspect the wiring in the house and on their own. But this should be done only when there is some experience with networks. First and foremost is to check all junction boxes in the apartment. Their twisting (especially copper and aluminum wires) should be removed. To connect wires you need to use special liners, pads or adapters.

Also worth checking the status of a transaction directly at the point of attachment of the chandelier or lamp to obschedomovoy network. Poor contact here is often the answer to the question about why the burn out led bulbs in the apartment.

An outage of such equipment may due to voltage drops in the network. For this reason, LED instruments it is sometimes necessary to change to cottages. Because of the city in Russia, the voltage is rarely stable. In this case, to fix anything, is likely to be impossible. Instead led the owners of the house will have to use incandescent bulbs. You can also buy some powerful stabilizer. For example, often in the cottages set devices "Resanta". In the presence of such equipment to use led lamps in the house is likely to be possible. However, "Resanta", unfortunately, switching can also give strong surges.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Why burn out the led lamp: chandelier

Sometimes such problem with LED-devices arise due to a malfunction of the lamp. Therefore, such equipment should be carefully inspected. It should:

1. To See all the contacts in the cartridge. If necessary they should be cleaned. This applies in particular to “tongues”, which it is also desirable to bend upwards. All of these actions in the future will provide a reliable contact of the lamp and the socket.

2. Check all fasteners. It often happens, for example, that the cartridge loosely tighten the screw. And this, in turn, usually leads to sincere and podgorniy. Napryajenie in the lamp due to weak contacts unstable. This is the reason that led bulbs burn out quickly.

The Low quality of the equipment

The market today are LED-devices as from top European manufacturers and Chinese or domestic. The first are quite expensive, but are reliable. Burn out quickly mainly Chinese lamps. This is explained primarily by the low quality of their Assembly. Domestic equipment of this type is relatively reliable.

Power Surges LED devices, as already mentioned, not tolerate. Therefore, their design included a special mini-stabilizer “driver”. Especially bad for the longevity of the led lamp high voltage. The Chinese in the Assembly trying to make a ice light bulb looked like “beautiful” primarily in the store. Stands in the Mall lighting usually do not charge. And that light bulb looked “worthy”, the Chinese put on a weak current limiter. So when you turn on the stand it lights up a bright light. And therefore looks store quality. If you enable in home network, such a device will experience severe congestion and eventually will burn out.

Of Course, not all Chinese manufacturers in the market supplying such a poor quality product. However, the risk of “bump” on a potentially short-lived LED device made in China, there are quite large.

Why blink led light bulb is in an enabled state

Burn, such devices are still quite rare. Most of the fault LED lamps is that they start to blink. This can happen both when turned on and when the off state of the device. In the firstcase the cause of the blinking can be:

• Faulty installation of the device;

• The old wiring in the house;

• The switch is not in the phase, and the “zero”;

• Poor driver in the lamp;

• Imbalance.

Sometimes it happens so that the light goes out after switching on, and then lights up. This shows primarily the fault of the starter.

What to do with the blinking of the device in an enabled state

The First thing to resolve such problem you need to check all the contacts in your network. If that doesn't help, you may need to think about replacing wiring in the apartment. In older high-rise buildings usually stretched aluminum wire. Powerful devices in homes today are used by many. Therefore, aluminum wiring may not handle the load. If the blinking occurs for this reason, wire should be replaced by copper.

If the bulb flickers just due to a malfunction, you can try to do the following:

• To get the filling device to insert the driver.

• In order to stabilize the lamp and solder in another condenser;

• Use one driver for all bulbs in the device.

Twink off

A Similar fault can be attributed to:

1. The Presence of the led backlight in the switch. The current flowing through it, to recharge the capacitor of the lamp. As a result, and there is a faint glow. To avoid this, you can try to replace one of the LED devices on conventional incandescent light bulb. This device will just "pick up" the excess voltage on yourself. Force him to light the incandescent lamp is simply not enough.

2. The Mismatch of the lamp standards.

Blink a led light bulb in the off state, and often due to a fault in the wiring of a house or apartment. In some cases this phenomenon arises from the work of a large number of high-frequency sources of interference (microwaves, electric cookers, washing machines, etc.). In this case, to correct the problem by inclusion in the scheme network stabilizer filter.

Selecting a lamp. Which is better to buy?

The answer to the question about which led bulb is better depends primarily on the particular construction of the device and its technical characteristics. When you buy LED, you should pay attention primarily on the following factors:

1. Bulb. most Often, the owners of apartments and houses, purchase E27 lamp (chandelier) and E14 (for small lamps). Such LED devices can be manufactured in the form of a bulb or "corn". The last lamp contacts of the LEDs on the outside are under tension. So they are pozharoopasny. For your home or apartment is better to buy all the lamp-bulb. Very good choice, for example, the lamp-globe E27 led. Such devices in terms of security and reliability are considered to be of sufficient quality.

2. Luminous flux. devices from good producers, this figure may vary between 900-1000 lumens per watt. For example, lamp led 10W can be an indicator of the light flux in 700-900 Lum. If the seller would convince the buyer to shop in other, best, the characteristics of the device, believe it is not worth it. LED lamp with an efficiency between 1300 lumens be too expensive. And therefore the apartments are just impractical.

3. Light the temperature of the lamp. of Course, for apartment you should choose LED device "warm white".

Is it Worth buying for "Aliexpress"

On the characteristics of the lamp for its purchase, pay attention to is, of course, necessarily. But it is equally important to look at the brand. This is especially true in cases when the owners decided to save money and buy a Chinese LED unit. Because the answer to the question about why the burn led bulb, often lies in the poor quality of their Assembly.

The Lamp with the “Incorrect”, for example, good properties do not differ almost never. But in this large online shop and sometimes found relatively good products of this type. Are quality lamps even on the “Incorrect” quite expensive. Not to be mistaken with the choice of the LED-unit on this site, you should before buying, at least read the consumer reviews about the product on his page.

Top manufacturers

If you continue to talk about China, the answer to the question about which led bulb is better is the products of the following companies:

1. Camilion. Lamps of this manufacturer belong to the budget category and are sold not only in Russia but also in Europe. Most consumers believe that the quality is relatively good.

2. Maxus. Quality “Camilion" lamp of this manufacturer are inferior. But still considered reliable enough. Most consumers are advised to purchase them, for example, for garden or garage.

Lamp from unknown Chinese manufacturers is better not to buy at all. For too long this ICE-light, most likely, will not serve.

Russian manufacturers of led lamps is mostpopular yavlyayutsya:

• «Optogan»;

• «Svetlana-Optoelektronika».

Available in the domestic market, of course, and good, relatively inexpensive lamp from European companies. The best such manufacturers are considered to be Gauss, Osram and Philips.