How to hang drywall: step-by-step instructions, features and recommendations

Working with drywall literally created a revolution in construction techniques. Because the finish that previously had to perform manually can now be replaced with drywall. He quickly, but efficiently creates a smooth surface, which is difficult to achieve in other ways.

Preparatory work

Before you start working with drywall, you need to draw diagrams or drawings and make calculations. If time is limited, it is possible to make sketches on the sketch. Next you need to decide what surface to install the frame. It can be installed both on the ceiling and walls in the living room. Why the need for a frame in the house?

It is used for different purposes - to create a double ceiling or to attach it to the chandelier and lamps. Its foundations allow as to level the surface and create a separate niche, if necessary.

Where the mounted skeleton?

How to hang drywall, it is important to understand that the material has many uses. With it it is possible not only to adjust the surface of the ceiling or create a niche, but also to create the arch, make decorative shelves and greenhouses.

Mount on ceiling

In the case of correct planning, when it comes to how to hang drywall, you need to start with the ceiling.

The Markup on it is from the most bottom place, which usually is defined according to a prepared scheme. If the measurement is inaccurate, you can also check them with a laser level. It is important to note that the transaction must be done before installation of the framework. After this, work will be much more difficult.

After making measurements is the mounting structure for ceiling:

• First, set the frame for mounts. If it is planned to install two-level ceiling, is two rows of hangers. The distance should be approximately 60 centimeters.
• The Mark that was made earlier, is necessary for fastening of the guides.
• You Need to mount the threads to the profiles, and thus to divide the ceiling into squares.
• In the markup thread the installation of a load-bearing structural elements. They should be attached to the suspension screws and inserted in the guides.
• For mounting profiles, cross connectors are used-crabs. For duplex ceilings – special duplex connectors.

When the frame after performing all these steps are ready, you can attach the drywall to the structure.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

If we are talking about how to work with drywall when the frame is not metal, and wood, the steps do not differ from the previous one. Below we will examine the stages of the work:

• Initially, the ceiling mounted metal hangers.
• It is necessary to prepare the wooden slats. They are also recommended to handle from moisture, so that later the whole structure has not suffered because of this.
• Slats are attached on a pre-made marks.
• Between the battens should be tensioned thread. What are they for? Thread will be used for installing sheathing.
• Furring strips are installed with screws. The bars are laid between the slats.

In the process of the installation design, you must first install wooden blocks on the edges, and then go to the middle of the structure. Once they are complete constructions installation of drywall.

Mount to wall

In the process of how to work with drywall, the next step in the installation is the wall. They don't differ too much on the technology, materials and tools from mounting on the ceiling. For example, to install a metal frame is used the following scheme:

• First mounted rails. On the one hand to the floor, and on the other-to the ceiling.
• In the process of marking a thread it is necessary to consider that the distance is different from what was needed for the ceiling. Thus, for wall distance must be at least 60 centimeters.
• Bottom guide profile must be equipped with brackets top and bottom. The design is thus fixed to the wall. Brackets should be located with the same interval as the marking thread.

If Windows

If the wall has a hole for entrance door or window, the process of how to hang drywall in the home is a little different. This should be used an additional profile for frame for gypsum boards. The guides are mounted around the hole. Further separately is attached to the profile top and bottom under the hole. The finished design then can be finished with drywall. Experts say that it is necessary to use the profile, near the window, otherwise it can later cause deformation of the whole structure.

Partitions and niches

The question of how to work with a profile for drywall, you must consider the installation of partitions and niches.

This stage starts with the selection of profiles. However, be aware that the guides size must be greater than those that were selected for mounting on the wall. This is because this structure will be fixed solely to the ceiling and the floor. The frame must be durable and sustainable. Otherwise, it will serve very little time.

The Installation partition occurs in the following steps:

• Metal guides should be fixed near the ceiling and the floor.
• In the next step, install vertical load-bearing elements.
• Next should be mounted with wood blocks exactly around the perimeter of the hole for the door. This is done in order firmly to secure it.

After performing all these steps we can safely say that the partition is ready.

As basis for the niche, it involves the use of the same guides and carriers, which are used for mounting on walls. But the process is not as simple as it seems. There will have to be creative. To create a shelf or niche in the wall, have to use guides. They have to adhere to each other. How to do it? For this purpose jumper.

If we are talking about the curved corners, there will have to use twisted guide. For shelves, they must be connected bearing elements.

During the mount process design under the framework necessary to carefully monitor the strength of the structure, as well as to make sure that the design can withstand the entire load which will be imposed.

How to work with metal stud crimping tool for drywall?

The Principle of operation of this device is largely similar to the algorithm of action of the stapler. It is necessary in order to interconnect the profile. The metal stud crimping tool is widely used in cases when you want to ensure that the design will be quite durable and will withstand high loads.

The Tool can be used not only in its basic configuration. Some models come with extra set of parts. They are used when necessary to make holes of different sizes on a particular sheet.

Nevertheless, the use of additional components not recommended too often. Otherwise, the tool will wear quickly and have to be replaced. Typically, the metal stud crimping tool changing solely the cutting element. Indeed, over time it wears out and becomes hard to cut.

Vetonit

How to work with Vetonit drywall? It is used in that case, if the surface is covered before pokleit Wallpaper on it. This material is considered one of the most widely used and most reliable.

Vetonit used for the filling of the entire surface under the drywall. It has good enough properties. Thus, the mixture does not change its form and characteristics over time. The composition may persist up to 24 hours without change of shape.

Putty that is in the process of repair were not used must be closed tightly with foil. And to subsequently form a crust. This factor would indicate that the top layer is not dry, and the material is still suitable for use.

How does the dowel for drywall “butterfly”?

This tool is often used in the construction industry. Dowel “butterfly” is used to hang relatively lightweight construction for the walls of plasterboard. It is used in the following cases:

• When it comes to the suspension of electrical wiring.
• If you need to fix the lights.
• For fastening of switches.

The butterfly is Also widely used for fastening skirting boards and cornices. The strict condition is that the thickness of the construction should not exceed twelve millimeters. That is, the use of this type of anchors is limited to certain parameters, which cannot be exceed. The advantage of this mounting is that the mounting screw is easily tightened, and it can be removed. However, there are also disadvantages. What are the disadvantages of this tool? It cannot be used if the rear space is strictly limited.

Conclusion

As you can see, working with drywall is simple. However, surgery has many of its own nuances and demands strict performance of all conditions. The only way the design will last a long time, and is not deformed in the shortest possible time.

As for how working with plasterboard in Germany, the technology is completely indistinguishable from those used by experts in any other country. The only difference is that in Germany, paying special attention to detail, and therefore tend to produce the most accurate calculations and measurements to prevent the slightest error. Tools and ways of working with drywall differ. However, each of them intended to speed up and facilitate the exploitation of the material.