Washing machine does not drain the water: the cause and sequence of actions

Washing machines are so solidly for a couple of decades into our life that the sudden failure of this unit's great kills the mood and breaks plans. Wash by hand is very tedious and long. And wring out the washed clothes as carefully as it does smart tech and is unrealistic. Here, perhaps, the most common complaint: washing machine not drain the water. The reason may not even be one. I'm sure many face sooner or later with a similar problem. And I want to understand why washing machine does not drain water. An overview of possible reasons is given below.

Electronic Failure

If appliances tripped halfway, it has operating cycle of the washing or rinsing all the parameters should be already finished, but washing machine does not drain - what to do in this case? At least to specify whether the program, which was such a nuisance, involves draining and pressing, and if so, may be to blame a failure in the electronics of the device. This can happen, given the instability of voltage in the national grid. The first thing to do is to restart the machine. Simply put: turn off the plug and reconnect it. If that doesn't work, you can re-select the program the rinse and spin cycle has already been using the buttons. In the absence of any effect the cause will have to look further.

Check hose, through which the drain

In the circumstances, characterized by the fact that the washing machine does not drain, the reason may be very simple. Probably just pinched, kinked or improperly installed drain hose. This, in fact, need to start – to eliminate the most obvious cause of the malfunctioning of appliances. It is enough to trace the position of the hose over its whole length, to straighten it and at the same time check for obstructions inside, and also control the requirement that the height placement of the inflection should be sufficient. As a rule, its minimum value is 60 cm from the bottom edge of the machine. If organized draining into the sewer, the problem may be clogging of the siphon. Need to remove the drain hose and lower it into the bath or basin. If the drain earned – it is necessary to clean the sewers.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Filter plugging

Making sure that it is not the drain hose is the main culprit of the fact that the washing machine does not drain, causes must continue to seek is already inside of it, namely, the clogging of the filter, which is equipped with a drain pump. This detail is most often located on the front panel under the tank, and you can get to it by removing the cover. To open it, you may need a flat screwdriver or a knife – it depends on the model. After removing the cover, it is possible not only to extract and, if necessary, clean the filter water pump.

You Can drain the water from the reservoir of the machine through a short drain pipe located in the same place where the filter. So care should be taken of the container with low sides or on several tight clothes so that the water is not turned into a vast puddle on the floor. As for the filter it may be clogged with lint from clothing, buttons, coins, hair, thread, husk of sunflower seeds or nuts and other small things caught in the washing machine along with clothes. The filter is normally equipped with a handle, which and twisted, sometimes rather tight as sealed by a rubber gasket.

The Blockage can be so severe that remove the filter yourself will fail, but the expert is on the shoulder. By the way, some cheaper models of filter machines will not be.

Under the above circumstances, in which the washing machine does not drain, the DIY repair is possible. To restart the program, straighten the drain hose or pull out and clean the filter, special skills are not necessary. The more that prophylactic cleaning of pump filter will have to be undertaken at least every five years, not waiting until it will remind formed a blockage resulting in malfunction of the machine. This procedure is usually detailed in the instructions to the machine. If the hose and filter checked and fine, but it changed nothing, and the washing machine does not drain what to do next? Next will be more difficult. Will have to get to the pipe connecting the pump with the tank washing machines.

The Need for cleaning pipe

If the owner of the washing machine not sure that I can find and get this part – you will have to turn to the masters. Craftsmen will be able to check the nozzle for signs of blockage and to collect all the design back without damage to equipment. If the nozzle clean but problem is not solved and still the washing machine does not drain, the reason may be jamming the pump impeller, or pump, for pumping water.

Check the impeller of the pump

This is simple enough. The impeller pump is located just behind the filter. After removing the filter it is visible in the hole. You can justtry to spin it the blades by hand, and if it rotates with difficulty – to extract what prevents it from spinning. If no foreign object is not a hindrance, but nevertheless during the spin cycle it is not spinning and the washing machine does not drain, the reason is obviously need to look at the pump.

The Problems with pump wear or failure

To Buy a new pump and put instead of old, broken, and on their own, but if your washing machine is out of warranty, it is better not to risk it. To service center this task will be quite ordinary. It is a consequence of problems with the drain pump often the case that the washing machine does not drain water. The reason is, as a rule, wear, breakage or manufacturing defects in the design of the pump. Usually the pump does not break overnight, this is preceded by multiple failures in its work, and strange sounds that it makes.

Other causes

If all of the above problems are eliminated, and the washing machine refuses to complete the process of washing or rinsing, drain the water and go into spin mode, the problem may be in faulty electronic Board of the device or a violation of the internal wiring of the machine. To do this yourself, just not worth it, you need to refer to specialists for diagnosis. You may need to re-flash the electronic module or a complete replacement. To restore the integrity of the wires of the washing machine also requires certain knowledge.

Insights

So, in the article the main reasons for such widespread problems as the failure of the washing machine during or after washing to drain the water and start the spin cycle. These can be failures in the electronic command apparatus, and the filter is clogged or sewage, wear pumps or just errors installing the drain hose. Sometimes the fault can be easily self-correct, but in many cases will need the help of masters. Deciding to fix the damage yourself, you must understand that in the event of inadequate action unit repair can cost you more. Now if the washing machine does not drain what to do – in General terms should be clear.