Repair and restoration of wood Windows

Due to normal wear and tear after prolonged use may require restoration of wood Windows. If the technological characteristics of the process and the selection of quality materials renovated structures will last quite a long time.

Major problems

Probably the most frequent defects of wooden Windows associated with the wear and tear of the hardware. And they, fortunately, most likely can be fixed, since it is enough just to replace worn parts with modern. Restoration of wooden Windows can be the case if the problems started immediately with the wood. This material is environmentally friendly, but easily susceptible to various external influences. To avoid problems, requires impregnation with antiseptics, which will become a reliable protection against insects. Depends on the life of designs and varieties of wood used: service life of products made of larch is 35 years old, and of oak – 90.

Step one: study the status window

Restoration of old wooden Windows starts by identifying the overall condition of the structures. To do this, carefully look around transoms, sills, frame. Old Windows are primarily:

1. Sloppy appearance, which is derived from the large amounts of paint.
2. Low insulating qualities, resulting from a loose fit of the transom to the frame and to each other.
3. Rotten areas on the transom and the window frame.
4. The distortions of the window.
5. Difficulty closing.

Restoration of wooden Windows with their hands begins with the definition of the method of fixing glass. Often they stay on the bead or just on the putty. Remove fillets neatly, so as not to damage the glass itself. And window putty just remove with a knife. After the glass is removed you can start removing the paint.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Step two: remove paint

During the restoration of the Windows of the old paint has to be removed – it is better to use construction Hairdryer. With it, the paint is well warmed up, after which well removed. Many remove the layers of paint with special washes, but their use is impractical, because the work with wood will have some time later, and the smell in the room will not be the most pleasant. Restoration of wood Windows, especially if they are old, can be an arduous process, so we need to foresee different ways of solving problems.

When removing paint from found all the hidden defects that will have to be overcome. Easy neytralizuya local cracks, rotten areas of small size, but if the wood has become loose over the entire thickness, many elements will have to be replaced. Problem areas can be the bottom corners – they are, as a rule, the main often accumulates moisture. In such cases, you may need the repair and restoration of wood Windows.

Step three: parse transoms

High-Quality restoration without this procedure is unlikely to be. The transom can be disassembled into separate parts, which allows to identify the main defects. However, if the angles remained intact and no rot, transom disassembly is not required. If the rotten areas are located, they are easily removed with chisels, mallet.

In place of the deleted elements will be required to insert the liner – it must be the same in shape and size harvested plot. The prepared liner is placed in the hole with glue, and then securely clamped. Restoration of wood Windows at this stage is completed by sanding the surface. When problem areas are repaired, treated areas need to be lubricated with antiseptic composition and dried. Carpenter's triangle will allow to align the angles. All the small bumps is also required to remove using putty on wood.

Step four: shpaklyuem and grind

Any cracks that appear in the course of repair, are carefully closed with wood glue and sawdust. When the glue dries, you can do the finish grinding. If there is restoration of wooden Windows with their hands, sanding should be performed using abrasives, which are selected under the condition of the transom. If it was paint, suitable for large abrasive, for example, P60: it will safely remove the desired layer. But if the surface have to do is close to glossy, you can use a fine grit-P180. Sanding wooden Windows – dusty process which it is better not to perform in the living room.

Step five: note the frame and the window sill

Restoration of wood Windows and doors – a range of activities, including repair of the frame. If it is badly rotten, you will have to remove it – typically, these rotten elements are easily removable. Longitudinal edge of the sill should be thoroughly studied – all the cavities under the sill blow out with foam. The area of the frame during the restoration it is better to create two elements – primary and secondary lining at the top.

Before work the window sill need to get rid of old paint, with the emergence of longitudinal cracks need to fill a wooden plank of certain thickness. If the sill is not in the best condition, you will need to replace it in such cases is unlikely to help the restoration. Historic wood window – theatre profile – one of the most complex in terms of repair, because it is an unusual design and decoration.

Step six: correct geometry

This is one of the most difficult stages of restoration, because the changed geometry of the Windows will have to make adjustments to the dimensions and to resolve the issue with the fit to the frame. The correction of the geometry is performed in different ways, depending on the condition of the transom. After correcting the defect of distortion will be gone. In some cases, you may have the capacity transom – this is glued a block of greater thickness and width than the slit. Is attached with screws and glue. After building the processed slit carefully polished to provide a smooth surface. After the height of the transom is completely customized before installation to try it in place to avoid cracks.

Step seven: asteksan window

Today, many companies offer this service, as restoration of wood Windows. Feedback on their activities were good because they perform all the work qualitatively and professionally. And glazing they are paying close attention. If this type of work have you decided to conduct yourself, remember that it should be performed in several stages:

1. First, the glass cleaned of putty and dirt. To avoid injury, it is necessary to work durable gloves.
2. Glass often placed on beadings or galvanized nails with a length of 20 mm.
3. Transom around the perimeter of the adjoining glass is processed with acrylic sealant, and then applied the glass. Fit glass to the frame should be sealed.
4. Final stage – painting of wooden Windows with a roller and small brush for hard to reach places.

Swedish technology: what's the point?

Restoration of wooden Windows on Swedish technology is that running a tubular insulation structures along with their repair. This allows to provide a high level of insulation. The method in cutting holes with a depth of 1 cm around the perimeter of the frame. These holes are filled with tubular silicone gasket that is resistant to paint and dirt. As part of the window so the sealant can serve about 20 years.

This technology has become popular in Europe 40 years ago. In the Russian version it has undergone a number of changes, which primarily affected the fit of the valves and locks, as well as sealing around the perimeter of the structures. Due to this warming heat stored in the room, but also achieved a high level of noise isolation. To a no less pleasant features of the technology include cost effectiveness and simplicity.

The benefits of restoration of wooden Windows include the following:

1. Thus it is possible to maintain the sustainability of housing.
2. In the house has the most comfortable climate.
3. Compared with replacement Windows, for example, plastic restoration – a more profitable event.

In addition, wooden Windows are often the highlight of many buildings. And they want to keep intact to show the building in all its glory. In addition, modern materials and technologies make it easy to carry out the restoration and repair of Windows to give them a fresh new look and to ensure the longevity of their operation.

Wooden Windows are structures, which should be cared for in a timely manner to preserve their attractive appearance. All scratches and areas with peeling paint be sure to mark...