Knowing how to set the ignition on a truck using a minimum of equipment and tools, you can solve this problem even in the field. It is necessary to understand the working principle of ignition system and also the reasons why it may crash.
Diesel cars correct to call the ignition timing. It represents the beginning of fuel supply at the approach of the piston to top dead center (valves intake and exhaust closed). In the working chamber creates a maximum pressure at this point is the fuel supply.
How do you set the ignition at KAMAZ? It would seem that it is once adjusted at the factory when production of cars and not worry about it. However, it is not so simple. The fact that each power unit has a specific timing, in connection with the peculiarities of the component elements of the motor. In addition, this indicator is influenced by quality and fuel type.
In any automotive power plant marks provided (C) that is designed just for placing ignition. If the system is adjusted strictly according to the marks, the motor will operate optimally, provided that the fuel injection pump, engine and fuel meet the standard characteristics according to GOST. By and large, pointers are a kind of guide to how to put the ignition on KAMAZ.
The car's high pressure pump for fuel is on the key side of the box, and the clutch pump can be fixed in two positions with a difference of 180 degrees. As a rule, if the screw drive is located in the upper part, it means that labels pump and couplings should be placed opposite.
Recommended
"IZH 350 Planeta Sport" – frisky Soviet bike
It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
Once all the details are exhibited on the label, it is necessary to tighten the clamping elements and to start the engine. The car should start no problem the first time. If the truck won't start or from the system exhaust is white smoke, it means the arrangement made in violation of 180 degrees. You will need to Unscrew the required details and deploy them to 180°, re-start the engine.
In the absence of labels or any extra ticks, it is desirable to expose the elements are approximately in the middle of the adjustment icons. To understand how to properly set the ignition on a truck, you must consider the characteristics of late and early injection.
In case of early ignition the piston does not have time to reach the top point, and the fuel begins to flow into the working chamber. The main signs of this:
For late injection timing, the piston goes down from top dead center, and fuel is just starting to go, the ignition is in pursuit. Signs of problems:
The Factory settings mostly involve a slightly late timing. If you want to adjust the node in the direction of early ignition, perform the following manipulation:
The regulation should be literally millimeter by millimeter, with the obligatory tightening of the bolts.
Knowing how to put the ignition on KAMAZ, once it is set to run the motor and check. If the operation of the power unit does not suit the owner, the manipulation of the setting continue to until when the sharp activation of the gas pedal appears a little ringing. After another small shift it will disappear, and will indicate the required timing. Correctly exposed point of injection will allow to achieve better traction, fuel economy, which is important when operating any equipment.
Setting timing is carried out simultaneously with the installation of the injection pump. Milestones is shown below:
Now consider how to put the ignition on KAMAZ “Euro-2” at the final stage. After tightening of the bolts drive clutch injection pump lift up the stopper, turn 90 degrees, lowered into the landing groove. In the lower part of the casing is mounted a shield of protection against dirt. The cabin of the vehicle is lowered, the latches are placed in the upper position.
Despite the fact that a diesel power unit has a simple and intuitive design, the elements of the fuel system are considered to be precision instruments. In this regard, the installation of the fuel high-pressure pump requires special attention and the optimum angle is determined by the injection timing of diesel fuel through the injector to the working cylinder in the compression stage. Even an error of one degree can lead to engine damage that will require an extraordinary overhaul. In various spheres of popular, reliable trucks KAMAZ “Euro”. How do you set the ignition for different versions discussed above. Knowing the specifics of this procedure, adjust the injection timing of fuel is quite real on their own with minimal time and equipment.
Article in other languages:
AR: https://tostpost.com/ar/cars/2305-how-do-you-set-the-ignition-on-a-truck-right.html
BE: https://tostpost.com/be/a-tamab-l/4066-yak-vystav-c-zapal-vanne-na-kamaze-prav-l-na.html
DE: https://tostpost.com/de/autos/4064-wie-man-die-z-ndung-an-kamaz-richtig.html
ES: https://tostpost.com/es/coches/4069-c-mo-poner-el-encendido-en-el-kamaz-correctamente.html
HI: https://tostpost.com/hi/cars/2306-how-do-you-set-the-ignition-on-a-truck-right.html
JA: https://tostpost.com/ja/cars/2305-how-do-you-set-the-ignition-on-a-truck-right.html
KK: https://tostpost.com/kk/avtomobil-der/4067-alay-oyu-a-zazhiganie-so-yp-ketken-d-rys.html
PL: https://tostpost.com/pl/samochody/4070-jak-ustawi-zap-on-w-kamaz-poprawnie.html
PT: https://tostpost.com/pt/carros/4067-como-colocar-a-igni-o-kamaz-certo.html
TR: https://tostpost.com/tr/arabalar/4072-gibi-g-stermeye-ate-leme-kamaze-de-il-mi.html
UK: https://tostpost.com/uk/avtomob-l/4069-yak-vistaviti-zapalyuvannya-na-kamaz-pravil-no.html
ZH: https://tostpost.com/zh/cars/2493-how-do-you-set-the-ignition-on-a-truck-right.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
Just check on the technical inspection of a car?
the Inspection is a mandatory process, and it will sooner or later have to go. Just check on the technical inspection of a car, you know not all the drivers. And they share their own experiences with each other, trying to anticipa...
"BAT-M" engineering road car class
Said that Russia always was the most powerful military equipment. Such an argument not only about the machines used for warfare, but also about the maintenance of adaptations in nature. A vivid example and undeniable proof of this...
How to choose a car seat for your child?
Every day small children are dying in car accidents, a fall in hospital in a serious condition. To protect your kid, it is best to buy a car seat for a child. Currently in Russia there can be penalties for transportation of childr...
Harvester Niva - the pride of Soviet engineering
With the beginning of autumn in the agricultural regions begins the harvest season. Heavy equipment leaves the field to facilitate the hard work of farmers. But few know that the Niva harvester, which is pretty firmly entrenched i...
Automotive industry of Russia was more happy user than the actual product. But there are very good copies with the optimal combination of practicality, quality and price. For example, «Lada Nadezhda”, which is very amb...
Tires Goodyear UltraGrip 500: reviews & photos
Winter tires made in the USA has always been a subject of dispute for many motorists. On the one hand, it has a relatively low price, and on the other — can it without testing in the harsh winters to cope with local weather ...
Comments (0)
This article has no comment, be the first!