The compressor on the vases

Date:

2018-11-26 14:00:24

Views:

472

Rating:

1Like 0Dislike

Share:

Table of contents:

Mount the compressor on the vases, can effectively increase the capacity of the motor. Due to the fact that amplified flow of air into the fuel system, increasing the charge of air and fuel mass entering the cylinder. However, the compressor has a negative side. In particular, increases fuel consumption.

To strengthen the compressor on the engine, you will need the kit, a set of keys, the paste is abrasive, the sensor to monitor boost pressure, air filter with low resistance.

The power Increase is due to the increase in the concentration of air in the fuel system.

To Start installation after complete cooling of the power unit of the car. After this you need to dismantle the air duct, standard air filter. Next Unscrew the bolts that fix the manifold to the exhaust pipe, and carefully Polish the pipes. The surface must be perfectly smooth. Bracket for tension pulleys, made in the form of the letter T, and the motor unit is a mounting bracket for the compressor. Drive belts pump and alternator should be removed as unnecessary later on. Instead, they used a special belt. With the compressor on the vases. The belt must be well stretched, however, to overdo it is not worth it. A small slack should remain. Otherwise, the likely increased wear of parts, which will lead to its rupture. It should be said that this element is to find independently of the kit is very problematic. It should also be noted that the belt is tensioned poorly, will SAG and slip on the pulley. This in turn would lead to a drop in power (or only a slight increase) and negative impact on the condition of the cooling system. Optimal belt SAG is half an inch when pressing on it with your finger.

After adjusting the belt tension should be set back intake «spider». Back mounted duct from the outlet of the “snail” to the intake port in the injector. It is recommended to avoid too sharp bends in the corrugated elements. In addition, you should avoid contact of the duct with the hot parts of the engine. The compressor on the vases should be equipped with a measuring device and sensor control boost pressure.

Next you must attach the filter reduced resistance. The compressor on the vases has the inlet pipe. To him and you must attach the filter. Position it should be in the coldest area under bonnet. Compression heats the air, it becomes additionally thinner. The lower thus the temperature at the inlet, so, in the end, it more will get into the motor. Due to this increase in the mass of the air / fuel charge, and accordingly, the power plant of the vehicle.

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

After the installation of the compressor should adjust the injector in accordance with the changing conditions of air supply. This is necessary to ensure that the engine has been “rich” blend. Usually set to do not produce their own. For this there are specialized services.

And on the dashboard it is necessary to fix the sensor to control boost pressure. He warned about potential problems, and to promote economical driving.

After the auto tuning to take care of the body. It is recommended to glue the stone chip film. After the compressor is mounted, the air resistance should be installed at a minimum. Should say that all work must be done after complete cooling of the motor.


Article in other languages:

AR: https://tostpost.com/ar/cars/11050-the-compressor-on-the-vases.html

BE: https://tostpost.com/be/a-tamab-l/19785-kampresar-na-vaz.html

DE: https://tostpost.com/de/autos/19795-kompressor-vaz-auf.html

ES: https://tostpost.com/es/coches/19806-el-compresor-en-los-floreros.html

HI: https://tostpost.com/hi/cars/11062-vases.html

JA: https://tostpost.com/ja/cars/11063-the-compressor-on-the-vases.html

KK: https://tostpost.com/kk/avtomobil-der/19783-kompressor-vaz.html

PL: https://tostpost.com/pl/samochody/19757-kompresor-na-waz.html

PT: https://tostpost.com/pt/carros/19758-o-compressor-em-vaz.html

TR: https://tostpost.com/tr/arabalar/19790-kompres-r-vaz.html

UK: https://tostpost.com/uk/avtomob-l/19777-kompresor-na-vaz.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Current leak in car how to check with the tester, a bulb, a multimeter?

Current leak in car how to check with the tester, a bulb, a multimeter?

every year the number of options and electronic systems in the vehicle increases. If the battery was only needed for engine start, but now it is still a source of power for music (often a subwoofer), registrars, non-standard on-Bo...

How to install xenon in the PTF?

How to install xenon in the PTF?

In recent years more and more car owners began to equip their vehicles with xenon lamps. By the way, put such optics not only for the main headlights, but fog lights. This high popularity is understandable. The fact that this ligh...

Car

Car "Ford GT 500 Mustang": characteristics and overview of generations

In the 60-ies came to light the same type of machine, which were subsequently consolidated into a single class-Muscle Car. They were a car of small size, issued between 1964 and 1973. 8 cylinders and powerful engines-so you can ch...

Replacing the clutch is difficult, but you need to know

Replacing the clutch is difficult, but you need to know

in order to begin such a task as replacing the clutch, not enough to know the Foundation of the theory. It is necessary to consider all the details and have even the slightest mechanical skills. To perform this type of work will r...

Crank mechanism: purpose and device, service and repair

Crank mechanism: purpose and device, service and repair

the Engine – perhaps the most responsible unit in the car. He produces torque to move the car. Based on the design of the internal combustion engine lies a crank mechanism. The purpose and the device it will be discussed in ...

Armored car ZIL Punisher: specifications and photos

Armored car ZIL Punisher: specifications and photos

In recent years, our defense industry is concentrated, in addition to the tanks and infantry fighting vehicles, on the development and production of armoured vehicles. One of these is the ZIL "the Punisher". Its appearan...