Painting stamped discs with your hands: procedure description and features

Despite its simple appearance, forged wheels will be a long time in fashion. Besides these discs look great classic cars (especially boiled, with shelf). These wheels are very practical – they do not crack, and in the case of damage are easily smoothed without any welding. But these drives have one big disadvantage – they rust. Over time, their appearance deteriorates. Which raises the question of their recovery. In today's article we will discuss how to produce "redesign", or painting, stamped discs themselves.

Methods

There are several methods to restore the appearance of these wheels:

• With the removal of the rubber.
• Without removing.

The First method involves a trip to the tire, then the paint is applied to bare drives. Yes, to apply enamel on the surface much easier. But there are some problems. If you hurry with pereobuvku and take these wheels to the tire ahead of time, there is a risk that the enamel would be damaged when installing the tires. Need to wait for the complete drying of the surface. Besides, not every motorist has a set of spare wheels. And the cost of tire can be up to thousands rubles. If we are talking about budget painting of stamped disks from a container with their hands, that method will not work.

The advantages of the method without ressortiront

Many motorists are choosing this method because it has several advantages:

• Time-Saving. To cope with the works in half a day. And if it is painted discs from the spray with their hands, if not 2-3 hours. After all, this enamel dries in 7-10 minutes. Besides, there is no need to spend time on the drive to the tire store and look for a second set of disks.
• Saving money. To paint the wheels with retreading is, you have to visit the tire. This additional spending. Also, when you see these tires definitely are balancing the wheels. All this comes at a price.

Is it Possible to paint on the spot, without removing the wheels from the car?

This is a quick way to paint disc forgings. But it is dangerous because on an incline the enamel will slide down. The result will be streaks. To remove them is quite difficult - have to remove entire enamel. So do not be lazy to remove the wheel and paint the stamped discs with your hands at a horizontal surface. The only way to achieve the best effect.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

What you need for the job?

To make the painting of stamped discs with your hands, should prepare:

• Spray. On average, a four-disc, 14 inches in diameter goes from 1 to 2 cans with a capacity of 400 milliliters. It is better to buy the supplies, so you do not run hastily into the store. And the rest will be useful for future painting. Indeed, over time, on any drive appear chipped. You can hide them the same enamel from stock. So buy at least 3-4 cans.
• Consumables. It's masking tape, degreaser and paper.
• Jack, balonnikom.

Not to prop up the car on bricks, it is best to paint the stamped discs with your hands on one wheel.

Preparation

First, the disks should be thoroughly cleaned. You can use a solution of detergent for detergent or automobile shampoo. After this the surface must be dry and treated with antisilicone. This solvent will wash away all the grease that is left on the surface.

The Fight against rust

As we said earlier, forged wheels tend to rust. To the new paint lasted as long as possible, it is necessary to avoid corrosion. To this end, the disk surface is applied with rust Converter. It is best to use the funds in the form of a spray. The composition evenly cover the entire surface area of the disc and create a protective zinc layer. Please give this matter much attention. Because if you apply paint on an unprepared surface (and antisoliton cannot corrode rust), the corrosion will occur at the first washing. If the major signs of corrosion, use sandpaper. Try not to use a wire brush – it will scratch the factory paint. As a result, the painting will be visible to significant risks and scratches.

By the Way, for those who wants to level deep scratches no filler on the disc, it is recommended to use ‘floatstone”.

Pasting rim

This is the most important phase of the work. From it will depend on the quality of the painting. And here opinions diverge. Some advise to paste over the old-fashioned way – a sidewall masking tape. Other insert cards in the contour. But there are other methods:

• Add the sides of the old wheel. Just need to find a junk tire with the same diameter (width doesn't matter) and cut the sidewall. It will serve as a kind of stencil. The method is quite fast and requires little care. Set exactly one sidewall to the wheel and just apply paint.
• The Use of paper in A3 format. It is quite solid, and it is not blown in the air like the A4. Set paper in the crack between the wheel rim and the tire horizontally.Additionally you can seal it all with masking tape. This stencil is reusable. When applying the paint do not soak it.

Paint Application

Of Course, the spray – this is not the best way to paint the stamped disks. His hands better to apply enamel from a spray. But since we have a budget painting is to use just such a method. So, basically, the sidewall, so that the enamel does not get to the part of the wheel. Next, shake the spray and produce the so-called processing layer. It needs to be very thin. If the metal has remained factory enamel paint without primer. The second layer will be thicker. Try to avoid stains – apply the composition evenly at a distance of 30-40 centimeters. In the same way and apply the third layer. If you want to achieve a glittery effect, use a transparent varnish. It must be applied also in several layers according to similar algorithm. The paint will add not only Shine, but will protect the topcoat from damage.

Conclusion

So we figured out how the painting is made of stamped discs with your hands. As you can see, this procedure can be repeated. And it is not necessary to remove the tyre from the discs (though this will greatly facilitate the work).