Valve cover: flow and Troubleshooting

Date:

2018-03-21 00:36:12

Views:

546

Rating:

1Like 0Dislike

Share:

Table of contents:

In the process of machine operation, motorists have to face different problems with his car. One such leak is the valve cover. About why it occurs and how to fix it, will talk in this article.

The Valve cover and gasket

Any driver who has seen what is under the hood of his car, aware of the location of the valve cover. It protects the mechanism, locking it from outside influence. It also provides protection from oil leakage. Element attached to the cylinder head through bolts and special gaskets cut to the shape of the head and cap.

valve cover

It depends on a sufficient tightness. On unsatisfactory condition of said strip resulting oil leak. In this case, you will need to be replaced.

However, before proceeding to the repair, you need to understand the reasons that led to depressurization of the part, as otherwise the seal will have to change again and again.

Oil from under valve cover

The Cause of any leaking lubricating fluid, from which the connection elements of the motor it may happen, basically, is the poor ventilation of the crankcase. It can be not only a valve cover, and fuel pump, and distributor, and more.

During the operation of any piston is pulled out part of the exhaust gases through the seal they seep into the crankcase of the motor. If the power unit is new, the amount of seeped gases will be minimal. But with good mileage of exhaust gases in the crankcase typed a lot, and eventually formed the excess pressure flows to the valve cover. To reduce it, a new car, there is an additional ventilation system designed specifically for the Carter motor.flowing valve cover

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

Crankcase Ventilation

Diesel powertrains equipped with two types of ventilation: for idling and for high engine speeds. Both systems consist of rubber tubes, through which the gases sucked into the intake manifold. Such a valve closes the system at idle. If it will not function, it will cause the formation of a very poor mixture in the intake manifold. As a result, the motor will start to shake, or worse, stall.

In order to Gaza, Carter took off with the oil dust in the valve cover mounted oil separator. It can become clogged with carbon and not work. Then the oil gets into the intake manifold through the filter, causing, of course, the smoke of the engine.

oil from under the valve cover

The Engine provided with the injection, has a single pipe suction gas, but closer to the throttle channel is divided into two. One that has a larger diameter, enters the manifold up to the valve, and smaller, which is usually clogged with slag, after it. Through this channel of smaller diameter is implemented ventilation at idle, and through the second — when the shutter is open. If the channels are dirty and the ventilation is not performed, and the exhaust form the engine is so strong overpressure that can not withstand any gaskets or oil seal. That's why the blow-by gases begin to flow out.

If you have found that is flowing the valve cover, before you attempt to repair the damage, you must fix the ventilation system so that even at a thousand revs a piece of cardboard on the valve cover would tightly cling to her. After all, when worn mechanism will not be able to get even at two thousand rpm, because the exhaust will break into the crankcase, and the oil leak will continue again and again.

Rinsing cap

When it detects that the valve cover is sweating, take it off and wash and gasket change. You may be surprised at the result. Do not forget about lubrication washers and bolts, by which is secured a valve cover. When washing you need to try to wash the oil separator below the mesh in it at least slightly clean. Setting the lid back on and tightening the screws, be careful not to disrupt the thread and not to crush the item.

valve cover Opel Astra g

16V

On the other hand, if you constantly maintain the oil level regularly adding it, leaks oil from under the valve cover there is nothing to worry. But with the 16V motor, mounted, for example, “the Lacetti” in which the candles are located in recesses, the condition can result in the failure of the ignition system. Therefore, valve cover “the Lacetti” in this case needs to be removed and the leak is fixed be sure.

Replacement pads

To replace the pads, you need to think in advance about the availability of all components, i.e. new constructions Hermetica and degreaser.

The Replacement is done on a cold motor, not to get burns and injuries due to hot parts.

The Procedure is as follows:

  1. A Car driven into a garage or on a level ground, open the bonnet.
  2. Remove the filter cover and Unscrew the bolts.
  3. Remove the remaining fasteners and the cover from the cylinder head.
  4. Connection of the elements is cleaned of the existing sealant and degrease.
  5. Handle new item sealingtool and do the installation in reverse order.

valve cover Lacetti

After the replacement, the head should be cleaned and start the motor. Upon detecting the leak immediately, most likely a gasket or sealant was of poor quality or the installation was in incorrect order.

In Order to avoid negative consequences, all parts, including valve cover “Opel Astra” G, on which is installed the aforementioned engine 16V, gaskets, sealants and everything else should be purchased in trustworthy stores selling auto parts.


Article in other languages:

AR: https://tostpost.com/ar/cars/10783-valve-cover-flow-and-troubleshooting.html

BE: https://tostpost.com/be/a-tamab-l/19341-zatamkavaya-vechka-cyachy-yae-l-kv-dacyyu.html

DE: https://tostpost.com/de/autos/19352-ventildeckel-flie-en-und-fehlerbehebung.html

ES: https://tostpost.com/es/coches/19363-de-v-lvula-tapa-el-fluir-y-la-soluci-n-de.html

HI: https://tostpost.com/hi/cars/10794-valve-cover-flow-and-troubleshooting.html

JA: https://tostpost.com/ja/cars/10795-valve-cover-flow-and-troubleshooting.html

KK: https://tostpost.com/kk/avtomobil-der/19341-klapandy-a-pa-a-u-zh-ne-ony-zhoyu.html

PL: https://tostpost.com/pl/samochody/19300-pokrywa-zawor-w-nieszczelno-i-j-rozwi-zywanie.html

PT: https://tostpost.com/pt/carros/19303-funcionamento-da-v-lvula-tampa-fluir-e-sua-resolu-o.html

TR: https://tostpost.com/tr/arabalar/19345-valf-kapak-ak-ve-onu-sorun.html

UK: https://tostpost.com/uk/avtomob-l/19332-klapanna-krishka-tekti-usunennya.html

ZH: https://tostpost.com/zh/cars/11591-valve-cover-flow-and-troubleshooting.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

UMZ-421, engine: specifications

UMZ-421, engine: specifications

the Engine UMZ-421 has a rich history. There are several modifications of the specified device. They are actively installed on the machines of the series UAZ. Amplifiers they use vacuum type. If you believe the experts, the device...

Adaptive cruise control: what it is and how it works

Adaptive cruise control: what it is and how it works

Every motorist heard something about adaptive cruise control. What it is, knows not everyone. In General, the system provides the next stage of development of the familiar cruise control. The main difference from traditional adapt...

Browse new Opel Astra Turbo

Browse new Opel Astra Turbo

After our market went out the updated model Opel Astra Turbo sedan, changed and different, the 5-door version of the car. Should immediately be noted that the new model is virtually unchanged externally. The only distinguishing fe...

KamAZ-65116: description, specifications, reviews

KamAZ-65116: description, specifications, reviews

Kama automobile plant – perhaps the most well-known enterprise in Russia engaged in production of medium - and heavy-duty trucks. These machines are used in every region of Russia – from the South to the far North. Kam...

Replacing the outer boot, the inner CV joint VAZ 2109. Replacing the seals CV joints 2109. CV joint replacement without removing the actuator 2109. When replacing the CV joint VAZ 2109 do I need to drain the oil from the box?

Replacing the outer boot, the inner CV joint VAZ 2109. Replacing the seals CV joints 2109. CV joint replacement without removing the actuator 2109. When replacing the CV joint VAZ 2109 do I need to drain the oil from the box?

the topic of the article – what you need to know about replacing the CV joint VAZ 2109, what subtleties there are in this case. In fact, there is nothing complicated, you don't even need to drive a car on the pit, all you ca...

Toyota Sera: model overview, photos and reviews

Toyota Sera: model overview, photos and reviews

the Toyota Sera was produced for five years. This machine is special because it is there that designers and developers of the company “Toyota" experimented with body styles and exterior. The so-called “biodesign&q...