Vacuum suction Cup to remove dents on car: description, types and manual

Date:

2018-03-22 08:10:13

Views:

638

Rating:

1Like 0Dislike

Share:

Table of contents:

Straightening work with the automobile bodies often requires specialized equipment. The situation is complicated by the fact that external defects have to be removed together with the paint coating. That is, solving one problem inevitably creates new challenges that require additional financial investments. In the case of small damages of the metal surfaces you can use an alternative and less costly means. So, gaining popularity suction Cup to remove dents, allowing not only to keep the paint in the problem area, but without the help of specialists.

suction Cup to remove dents

Device tool

The Design is quite simple and particularly difficult in the treatment is not. The functional basis is based on the suction Cup, which is made from a combination of durable plastic and rubber lining. This part in the process captures the damaged area and then provide a force that pulls it, restoring the original geometry of the surface. The second important component is the reciprocal of the hammer, which is action. There are models that operate on the principle of hydraulics, and simple modifications of the implement lever pressure. In both cases of the suction Cup to remove dents without painting can only work with injuries, the appropriate sizes. Most models fixes only shallow indentations with a diameter of about 15-20 cm where there is significant bending metal or sprain, the tool will be ineffective.

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

vacuum suction Cup for removing dents

Varieties

In addition to hydraulic and mechanical lever suction cups is also common compressor station. Such modifications have stress from the pressure, blowing with compressed air. If manual efforts are not enough, it makes sense to apply to such equipment. Distinguish between the tool and the location configuration of the cups. There is a single model with a single point of capture, but large diameter. And to work with large areas of defect, it is expedient to use models that combine 2 or 3 of the suction Cup. Such a device not only extends the area of operation of the mechanism, but also minimizes the contact area with the paint coating. But it is important to note that multicomponent suction Cup for removal of dents requires experience and proper training in operation. Some versions also involve the execution of the operation with the connection assistant.

suction Cup to remove dents without painting

Preparing for the hood

The quality of the correction of problem areas is greatly influenced by proper preparation. It is imperative to clean, rinse and degrease the work area with the help of special chemicals for the body. Prepare and suction Cup. It is linked to the hammer by means of thread. It is important to ensure that this part in the process of drawing can provide a smooth and unobstructed course. To correctly fix extremely undesirable jerks, so it's best to check the thread until before the start of the straightening procedure. By the way, if the suction Cup to remove dents on the car has insufficient length of the line pairing with the hammer, it is necessary to prepare and an extra washer. But such inclusions are advised to avoid – the shorter rod with the broadcast efforts the hood, the more effective the control of the restorative deformation of the metal.

Usage instructions sucker

Auto vacuum is realized in several stages. After he was done cleaning the surface, it is necessary to identify the point of capture. Here an important geometric calculation to the force provided for the hood in the right direction. To start the operation preferably with the edges of the zone of deformation towards the middle. Fixation of the round suction Cup is made with a special adhesive. Thus it is necessary to wait 5-10 minutes to have it grabbed in place of applying voltage. Later in the course is the hammer, and, depending on the principle of providing the power of influence that begins the process of drawing with a corresponding offset in the direction to the center of the problem area. According to the scheme circular movement with reduced radius damage should gradually shift the suction Cup to remove dents. With his hands this operation is preferably performed in gloves, and if you are using the compressor unit, the compressed air must be strictly balanced. Excessive stress can provoke the opposite effect of drawing beyond the normal plane of the body.

suction Cup to remove dents on car

Positive aspects of using suction cups

Since the advent of the vacuum snap to pull the dents to this technology, there is skepticism. Few motorists believed that the tool actually preserves the paint and pulls the metal surface. Nevertheless, the effectiveness is the main advantage of the method. With proper training the deformed plot has all the chances to leave in its original form and decorative coating of the body. Also the suction Cup for removing dents takes a little while for the surgery. According tousers, typical shallow damage corrected by hand for 30-40 minutes.

Disadvantages

suction Cup to remove dents with your hands

Unfortunately, the method does not give 100% recovery of geometric lines. Even professional plumbers don't always achieve visually smooth surface. But, given the simplicity of the recovery mechanism and results in many satisfied. Another disadvantage of the method lies in the restrictions on its use. It was already mentioned that the vacuum extractor suction Cup to remove dents could not be applied in areas of strong stretching and bending metal. But also this method cannot be utilized if the deformation zone has damage to the paintwork. The fact that the preservation of the paint layer in this case must not count. Coverage will be even more destroyed by the suction Cup and the vacuum gripper may not work.

The Nuances of tool selection

In selecting the suction Cup you can stick two tactics. Or buy an ergonomic universal model with multiple points of engagement, or purposeful acquisition of a mechanism to work with the specific characteristics of dents. Next, the method of force effect, which will depend on complexity of performed operations. To work with the shallow defects will approach and manual suction Cup to remove dents, and massive damage to a large area easier to fix by means of the compressor.

vacuum extractor suction Cup for removing dents

Alternative technologies

Before the advent of technology the vacuum alignment of handyman in the garage have used the technique of drawing from within the same linkage method. But today, this technique is almost never used because of the complexity of the organization of its implementation. But a proliferation of magnetic suction Cup for removing dents. With your hands you can implement this technique and without any special tools. Enough to arm themselves with a rag and a magnet block with sufficient voltage. Next, using the lining cloth of the active element is superimposed on the dent and pulled back. In terms of efficiency, this method is not so impressive compared to the factory glue vacuum, but correction of small damages is quite feasible.

Conclusion

suction Cup to remove dents with your hands

The Use of compact vacuum with suction Cup to restore the geometry of the body is organically part of the concept of garage repairs on people's technologies. The method is simple, efficient and, most importantly, cheap. The basic set of the device on the market can be bought for 1-2 thousand. p. Adding a few thousand more, the Arsenal of tools you can refill and multifunction straightening station with a compressor and multiple points of capture. But in any performance vacuum suction Cup to remove dents and also assumes certain risks in terms of deterioration of the situation. It is also characteristic for traditional methods of repair. Many beginners mistakenly believe that the key to successful implementation of vacuum is in the power potential distortions. This is not so, since most often the effort is enough. Another thing is that it is not always possible to find an optimal balance between effort and direction of its application. Therefore, there is a likelihood of excessive deformation of the area covering the flat area.


Article in other languages:

AR: https://tostpost.com/ar/cars/8620-vacuum-suction-cup-to-remove-dents-on-car-description-types-and-manual.html

BE: https://tostpost.com/be/a-tamab-l/15451-vakuumnaya-prysoska-dlya-vydalennya-uvagnutascya-na-a-tamab-l-ap-sanne.html

DE: https://tostpost.com/de/autos/15462-vakuum-sauggreifer-f-r-die-entfernung-von-dellen-mit-dem-auto-beschrei.html

ES: https://tostpost.com/es/coches/15471-vac-o-de-la-ventosa-para-la-eliminaci-n-de-abolladuras-en-coche-descri.html

HI: https://tostpost.com/hi/cars/8630-vacuum-suction-cup-to-remove-dents-on-car-description-types-and-manual.html

JA: https://tostpost.com/ja/cars/8627-vacuum-suction-cup-to-remove-dents-on-car-description-types-and-manual.html

KK: https://tostpost.com/kk/avtomobil-der/15453-vakuumdy-sor-yshy-zhoyu-sh-n-zhanshyludy-avtomobil-de-sipattamasy-t-rl.html

PL: https://tostpost.com/pl/samochody/15427-przyssawka-do-usuwania-wgniece-na-samochodzie-opis-rodzaje-instrukcja.html

PT: https://tostpost.com/pt/carros/15422-ventosa-de-v-cuo-para-remo-o-de-amassados-no-carro-descri-o-tipos-e-in.html

TR: https://tostpost.com/tr/arabalar/15456-vakum-enayi-kald-rmak-i-in-ezik-bir-araba-tan-m-t-rleri-ve-kullan-m.html

UK: https://tostpost.com/uk/avtomob-l/15441-vakuumna-prisoska-dlya-vidalennya-vm-yatin-na-avtomob-l-opis-vidi-ta-n.html

ZH: https://tostpost.com/zh/cars/9373-vacuum-suction-cup-to-remove-dents-on-car-description-types-and-manual.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"Renault Megane 2": reviews, description, specifications

"Reno" - a rather popular brand in Russia. This manufacturer produces reliable and inexpensive crossovers and passenger cars. One of the popular models in the line "Reno" is "Megan" second generation....

A description of the main characteristics of the Quad bike

A description of the main characteristics of the Quad bike "Stels 600 Leopard"

"Stels ATV 600 Leopard" – is the first truly Russian ATV. It is mainly applied to repair parts domestic. Designed and assembled "Stealth 600 Leopard" in Zhukovsky Motorcycle and Bicycle. For optimization of the manufacturing...

The connection via fog light relay: diagram, step by step instructions

The connection via fog light relay: diagram, step by step instructions

If your profession is connected with frequent trips, or you just love travel, then you probably know that without good optics to ensure the safety of the drive is quite difficult. At the moment, even the shortest trip should not b...

Reviews: the engine

Reviews: the engine "Chrysler" to "Gazelle". Engine mounting Chrysler to Gazelle

for the First time the car "the Gazelle" has appeared in 1994 and was released by Gorky automobile plant. The machine showed a good side. Just been repaired, proved to be very reliable. The only drawback is the engine. Although at...

An overview of the car

An overview of the car "Renault-Docker"

Model of Renault Dokker is a versatile five-seater that can be used in both professional and personal purposes. Considering the fact that its cost is relatively low, the manufacturers still is able to sell cars in the European mar...

Replacing the power steering fluid: how to do it?

Replacing the power steering fluid: how to do it?

owning a car is very convenient, you can get into any place at any time of the day. Besides, if it's not just a car, a luxury model from a reputable manufacturer, the drive for "iron horse" will bring great pleasure. And...