In the construction of private homes in recent times are increasingly using aerated concrete blocks. This circumstance is no accident. Said material has a porous structure, which is characterized by high thermal insulation qualities.
Concrete absorbs a lot of moisture and dust, as a result, it oxidizes, becomes hard, dark and loses its quality advantages. In order to avoid this, performed exterior finish of houses made of aerated concrete. This makes the façade is resistant to external environmental influences.
Before performing work on the finish of the concrete on the outside, you should be familiar with the basic technologies. The most economical method is the application of plaster. It is important to choose the right composition, preferring permeable viscous mixture. In order to achieve higher strength, the layer should additionally use a reinforced mesh, especially for complex areas, namely:
The Exterior finish of houses made of aerated concrete can be made using the bricks. This should make the Foundation more sturdy. Its width should include brick and block. For the reason that the panel transmits less heat than concrete, is formed by the gap between the materials. Its width should be 50 mm. This approach will eliminate the build-up of condensation inside the construction. Ventilation is provided by the blank seams between the bricks, which are left at the top of the walls. The total area of these seams shall be 1% of the total area of the building.
Recommended
The most effective methods of seed germination
Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...
Retro-reflective paint. The scope of
When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...
How to make icon with your own hands - options izgotovleniya (simple and complex)
In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...
If aerated concrete blocks have a low coefficient of permeability, the formation of air gaps can be waived, however, this approach may not be the best, because it will increase the thermal conductivity of the walls and lead to cooling of premises. Heating costs will be more impressive. Without the formation of gaps is possible to impose a summer cottage or houses.
Clad facades with brick, use the sheet that will withstand the contact of the blocks with mortar. The canvas as you move brickwork shifted. Cladding can not be stacked without supports. For example, a brick connected with blocks that will allow you to obtain a monolithic structure. This indicates that every square meter should be placed at the four. They should be provided in advance. This is usually used a metal strip, when made basalt-plastic, perropolis of galvanized steel. Elements are inserted in the blocks, whereas the other side – brick.
The Exterior finish of houses made of aerated concrete can be made with paint. It will be cheaper than other solutions. To use this requires a special composition or putty, which must be permeable. This will protect the units.
Before applying the paint diluted with water. As a downside of such a lining acts quite a long time in the preparation for external walls. All seams and irregularities must be cleaned as dents and protrusions. Aerated concrete blocks can be prepared by the method of cut chamfer around the perimeter. This will ensure smoothness and flatness.
As another popular cladding material for aerated concrete is the siding. It can be made on the basis of different materials. This:
This allows you to protect the facade from the weather. The role of the advantages of this approach is the opportunity to insulate the walls of a method of installing insulation under the sheathing of siding. Frame, by the way, will perform a major role in the skin, in fact it will install the panels, and the gaps between them will provide a ventilation design.
You can be performed exterior finish of houses made of aerated concrete, fibre cement panels. The mount can be made directly to the wall with screws. As alternative solutions, performs installation of the frame. In both cases, are used for the Assembly of the brace-claimer through which the fastener is screwed into the elements of the sheathing or the wall.
Fiber-Cement elements are fixed to each rack. Distance between fasteners shall be 600 mm horizontally. Claymore are installed more frequently in areas adjacent to door and window openings and building corners. Such exterior walls of house of aerated concrete sometimes calls for the formation of the air gap, which in some cases is used to install insulating material.
Experts do not recommend to mount the panel to the frame or wall without Kleimenov, but in some cases such an approach is the only right one. This is true, if the panels need to be fixed in areas where it is impossible to install the bracket. In this case, productsdrilled through and threaded holes screws, the cap of which is recessed inwards by 1.5 mm. After lining the holes with plaster smeared with moisture-proof characteristics. For this purpose you can use a paste sealant, which is selected according to color, and sometimes supplied.
Before you start work, you can consider photos exterior house of aerated concrete. If the quality of the material used for lining, fibre cement siding, the technology will be slightly different. Elements are installed at an angle, they are positioned with an overlap of the top boards on the bottom. This allows you to get the effect of a ship's deck or tree.
The Siding will be located exclusively on the upper side of the panel and be secured to each strut of the frame. Docking Board in length between them should leave a gap of 2 mm to compensate for linear thermal expansion when exposed to temperature. Cap screws will overlap above the fixed boards. Plate to the wall may be installed to the framework method. It involves the use of a metal framework, the grooves in which are mounted fibre cement panels. In this case it will be visible to the surface of the plates and rails framework.
If the external decoration of the house of aerated concrete is carried out using fiber cement panels, the sheathing can be made from wood or metal galvanized profile. Horizontal elements made of timber must have a cross section of 50x30 mm. Distance between them on the wall will be equal to 600 mm. For fixing anchors are used. Vertical racks of a skeleton, as a rule, have a size in the range 40x70 mm. They are fixed with two screws. The step between the vertical bars is also usually equal to 600 mm. These parameters should be followed also for the reason that insulation is usually available with such sizes. This indicates that its styling will be easier, and waste less.
In some cases, cladding, fibre cement boards and planks is on pavement before joining the eaves. The cap is not released. Otherwise, it is necessary to form the frame of the zigzag type, the lower part of which will be filled with expanded clay medium fraction. This material acts as an insulator and will protect from rodents.
To eliminate the need for plastering walls, the gap is filled with cement mortar, which is pre-blended with polystyrene chips or polyurethane foam. Filling should be carried out consistently, what will happen as fixing decorative panels. If the decoration of the house of aerated concrete, fibre cement, is conducted outside elements, no matter what method of installation no was selected, should start from the bottom of the wall. You can move from blind area, which is true if you plan to coat this material base.
When cutting slabs, the saw cut should be painted with an acrylic composition, which quite often comes in the kit. Paint will help to disguise the cut and be a protection for the mechanical parts from moisture and other factors. After completion of the installation of the panels on the plinth of the wall and above it is necessary to install a metal drip cap. Easiest to install is the one that is attached to the wall.
Having Considered the options for decoration of houses made of aerated concrete, you can choose fiber cement boards, which needs to be installed and around Windows. To cope with this job as carefully as possible, you should use the separation bar. Gaps are closed with special decorative area, which will improve the appearance. If around the window there was a broad slope, then they can arrange the same panel, to the junction of turned out neat. This box is fixed starting profile, and the grooves are mounted plate. Gaps before installing them plates promazyvaetsya with sealant.
The House of aerated concrete for finishing is to be prepared with a brush. Chips and dings are sealed with the adhesive is pre-mixed with the dust of aerated concrete. Minimum layer thickness is 10 mm, the material may be reinforced. In the composition there is a cool additive, so that the mixture will stay on the surface of the most durable. If the layer thickness is increased to 15 mm, then reinforce it with a mesh of fiberglass. More impressive by the thickness of the decoration of the house of aerated concrete is impractical.
When Choosing a mesh, you should choose the cell which is approximately 3 mm. the Material should be resistant to alkaline media. Otherwise after some time the mesh will lose strength and cease to hold the plaster as a finishing layer will just drift away. First apply the primer mixture, after the reinforcement. This will create the basis for the decorative plaster.
Applying makeup is strip. Before the mortar hardens, it should lay the grid by pushing it with a trowel or notched trowel. As soon as the grid goes down, you should use a wide spatula for leveling. The surface at the final stageleave until dry. This period may vary over time depending on the material used. The decoration of the house of aerated concrete in the next step comprises applying a primer that covers gray and reduces the porosity. After the primer has dried, you can proceed to applying the decorative plaster.
Quite often consumers ask the question about what is better external finish of the house of aerated concrete. Among other solutions, you should select a tile that can be ceramic or clinker. Its surface is able to withstand corrosive substances and precipitation. The weight of such cladding below in comparison with the brick, which reduces the load on the Foundation. The tile sizes are small. This indicates that solid veneer will be time-consuming.
Sometimes the clinker used for the decoration of fragments of the facade. In this case the tile goes well with plaster. Exterior finish of houses made of aerated concrete can be made even with the help of thermal panels, which are typically used with an impressive façade area. This allows you to perform decoration and insulation. The front side of these panels in factory environment is complemented by stone or ceramic tiles. It is in this case is natural.
For walls of aerated concrete as a finish you can use one of the many materials on the market today. Extras should be allocated to granite, which has a more impressive in size compared to ceramic tiles. This makes it easier to work on a continuous facing wall. To mount the granite on a wooden crate or glue. In the first case will ensure good ventilation of the facade.
Porcelain Stoneware tile if necessary, the insulating walls can be installed on aluminum profile. To prepare the facade would have to be very carefully. The surface needs to be protected, sealed seams, and potholes filled with foam.
Article in other languages:
KK: https://tostpost.com/kk/domashniy-uyut/24879-syrtyn-rleu-yler-gazobeton-n-s-alary-ke-ester.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
Accumulator: a device that adjusts
Almost every modern house has the water supply system, a required element of which is the accumulator for the water. However, some owners of private property are wondering what it does, is it possible to do without it? In this art...
When to plant strawberries: how to determine the optimum planting time
So nice when in the garden in early summer appear the red strawberries. It is loved by both adults and children. And in the winter when the course is strawberry jam, jam, compote, very nice to enjoy these treats. However, this cro...
How to make a floor on the ground
Technology floor covering on the soil surface is often applied in the projects of country houses. Moreover, it should not be confused with decorative trim as such, is formed as a multi-purpose “cake”, in the capabiliti...
A review of the TV LG 32LB551U
equipped with the larger rear blocks gradually go by the wayside. Now the majority of buyers prefer LCD models. In the Russian market many domestic and foreign brands. In short, the choice is very large. This can be considered bot...
Installation wiring in a wooden house and the apartment
In modern society, it is impossible to imagine a house without electricity, so each room needed a quality installation of the wiring. The production of such work is best left to a professional electrician, but it is possible to pe...
Onduline: sheet size, material properties and area of application
Today one of the most popular roofing materials Ondulin. The size of the sheet, resistance to stress and light weight make it convenient.Onduline is a corrugated fabric, made of pressed cellulose, which is impregnated with bitumen...
Comments (0)
This article has no comment, be the first!