Drill bit for ceramic tiles. What drill bit drill ceramic tile? Drill bits for glass and ceramic tile (photo)

Undertaking a repair in the kitchen or the bathroom, many owners choose finishing material ceramic or glass tiles. It is a fragile and hard coating. If handled incorrectly, it appears chipped and cracked. Therefore, the drill bit for ceramic tile should be of a certain type. Because sometimes you need to make holes in material as thin and very large.

For Example, in the bathroom often drilled ceramic tiles for hooks for towels, and the kitchen in the coating leaving a place under a gas or water pipe. Before work is necessary to choose the correct drill bit for ceramic tiles.

A Tool to drill

To select a drill bit for ceramic tiles, you must first determine the tool. Depends on the correct execution of the entire work.

To make a small hole on the glass or ceramic tile, you'll need a thin drill bit and hand drill. With this tool you can control the pressure and speed of rotation.

Drill bit for ceramic tile is also used in electric drills and screwdrivers, which have the function of smooth motion. The tool when working there should be no sharp jerks or vibration.

Will Not fit the rotary hammer or impact drill with a drill bit for ceramic tile and glass. They will split the material. They can be applied only after complete drilling of the cover when you want to make a hole in the base of the wall.

Professional drill bits

Drill bit for ceramic tiles, photo which are presented next, have one distinguishing characteristic. They are the tip harder than glass or tile. There are specialized drill bits and tools used in the home.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

If you use them often, then you should buy a cutter with a diamond dusting. It is the most expensive. But in working drill bit for drilling ceramic tile with diamond coating were the most effective.

A Professional technician, using this tool in their activities, quickly pay for the cutter. But in the home such equipment is considered unprofitable.

Mill for home use

In the case where you need to drill yourself some holes, buy a diamond drill for home use will be expensive. Therefore, manufacturers are producing cheaper equipment solely designed for infrequent use.

Their tip has pobeditovyj a tip. Hardness of the cutter enough to make the hole of different diameter in the tile. However, the work with the use of such a drill is longer.

Actions must be performed carefully. Also today, the manufacturers and other types of drills. Their tip is not made of pobedit, and other super alloys. Therefore, acquiring a mill for tile, you should pay attention to the purpose of the tool.

Drill for large diameter holes

In order to determine what drill bit drill ceramic tile, you must consider the diameter of the hole. Sometimes the tile you want to make place for the socket under the faucet or pipe. In this case, will require a mill of a certain sort. It is called a crown.

This is a tubular drill bit having a diamond coating. It also comes in different sizes. Set of crowns are quite expensive. It is beneficial to buy professional repairmen.

However, this tool is able to provide the best result. The duration of action decreases, and the efforts of the master become the minimum.

With the tubular drill to make the holes in the tiles up to 15 cm diameter.

This type of cutter should not overheat. So it should be lowered into the water. A drill or screwdriver should run at minimum speed.

How to use diamond crown

Drill bit for glass and ceramic tile by type crowns require proper maintenance. This method is suitable for tiles, which have not yet been glued to the base.

Before you start, you need to make a mark, which will be the future hole. Drilling is performed from the front side of the tile. In this drill should not be much pressure.

If diamond crown new and sharp, without a lot of effort tile can be drilled for 2-5 minutes.

Also, be aware that this type of drill does not tolerate overheating. Otherwise, it will quickly become blunted and worn. Therefore, the work when the part is produced in a small rpm, and the mill periodically cooled (immersed in water).

Tungsten holesaw with pilot drill bit

If the tiles already laid on the base, then drill a hole in it large diameter is very problematic. This applies to a mill such as tungsten holesaw with pilot drill bit.

Work should be carried out very carefully. Because the drill bit for ceramic tiles, used incorrectly, may cause replacementthe whole coating unit.

When using tungsten crowns you can get a great result, even if the cover has already been mounted.

So that the cutter does not slip on the surface of the tile, you should use the template with the appropriate diameter. It is pressed against the wall. Then drill with the crown is pressed to the wall and the process of drilling. In the case of the already laid tile, master has to act especially careful not to damage the masonry.

Drill bit "bunhead"

If you want to make a hole custom sizes, builders often use a drill for ceramic tile "bunhead". The cost will be less than tungsten or diamond crown. But with this cutter you can work even on the surface of the already installed cover.

Drill bit for ceramic tiles under the name "bunhead" is shaped like a compass. Therefore, the hole diameter can be adjusted.

This drill for ceramic tile, a photo of which is presented below, is the cutter of durable alloys. The Cutter in the middle is used to define alignment.

The Disadvantage of this equipment is the difficulty of retention when creating holes of large diameter.

Drilling under the anchors

The Holes for the dowels need to be drilled out, most likely, already assembled coating. Such work is carried out, if necessary, to hang a shelf, mirror, hooks for towels, a lamp and other accessories.

For drilling holes for dowels should consider a number of features. Coated ceramic tiles are usually pretty slippery. Mill is thus able to shift. It'll ruin the coating, and the result will be unsatisfactory.

To avoid this, the tile is glued to the masking tape. This will facilitate the work.

You Also need to remember that drill for concrete is not suitable for tile. So it does not split, it is necessary to use only special tools. Are the recommendations for carrying out such works.

Expert Advice

To drill for ceramic tiles and glass have fulfilled their task in the best way, you need to work to listen to the advice of experts of construction and repair business.

From the edge of the tiles need to retreat to a distance of not less than 15 mm, so it does not split. Before operating the tile can be soaked in water for an hour. It will also prevent the formation of cracks and chips. Allowed just to moisten the drill holes with water.

The safest place to create holes in the already assembled coating are considered mezhplitochnyh seams. Possible the dowels should be installed here. Although the choice of drilling is not always possible. Therefore, when carrying out the work should always stick to small speed drills, should also push hard on the surface.

If the wrong approach to the conduct of the bore, you can damage the finish. Sometimes when cracking the tiles have to change a few elements of the cover.

After Reviewing the recommendations as to what should be the drill bit for ceramic tiles, to pick up necessary equipment is not difficult. Correctly performing all actions in the home and in the assembled coating to make the necessary holes in the tile will be under force even to a layman. In carrying out the work should take into account the recommendations of professionals about the technology of its implementation.