How to make doors in the bath with their hands: step-by-step description and drawings

The Door to the bath with their hands will be able to make any person who has experience with woodworking tools. However, if you do not observe the technology in the room will be drafty, the heat will go out, and hygienic procedure is not so comfortable.

Selecting material

If you decided to make the door leading to the bath, then you should know for this suit is not any variety of wood. For this design it is best to use birch, exotic wood, oak or aspen. Affordable traditional pine, in principle, can be used for the manufacture of doors, but it is better to use this material for the inlet design, and not for the washing or steam room. Glass doors are often used today, as they excellently withstand high temperatures, humidity and easy to care for. The only drawback is the high cost, and to make this painting your own is difficult.

The Door to the bath with his hands you can make from metal, which is characterized by durability and strength. Most often, these doors act as input. Heat-resistant plastic also has excellent performance characteristics, including durability, strength, resistance to temperature and humidity, as well as reliability. If you wish, you can order the canvas, the surface of which imitates natural wood or any other materials.

Preparatory work

Doors in the bath with their hands it is still made of wood, despite the fact that on the market today these products are available in wide range. For this, you need to prepare floorboards, whose dimensions are 30х200 mm, you will also need lumber for framing paintings of square section with a side of 30 mm, screws, timber for reinforcement 30 x 20 mm, the adhesive filling grooves and hanging loop. If you are planning to build the front door, it is necessary to prepare the insulation, the nails for fixing the colour options, the colour options, line or wire, and also accessories. Door frame will be made of timber 11х6 see Need foam, fake planks, clamps, drill, planer, tape measure, hammer, drill with set of drill bits and anchors. For cutting wood you can use an electric jigsaw, and for processing of the material will approach the plane. Can't do without a caliper, level and scissors.

Sizing

Before the door to the bath with your hands, you should determine the dimensions of the canvas. Previously, the dimensions of this design were less than usual today. The small size helped to reduce heat loss. Old baths were insulated with moss only, which is why the need heat preservation was relevant. Modern buildings have high thermal insulation properties, so they can install a door in full growth. Standard dimensions of this design are 2000х800 mm.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Work on the door leaf

So, you're thinking about how to make a door in the bath with his hands. What will be the procedure? In the first stage floorboards are disclosed in length. In the above-mentioned size in height is more strapping canvases to use timber with a width of 30 mm.

The Timber to be fixed on the perimeter of the canvas, so you need to make a fairly simple calculation: of the 2,000 we need to subtract 60, which will allow to 1940 mm, it is in this setting and should be cut out of the Board.

The second step is to determine the number of boards in the canvas. The width of the element, along with the rail is 800 mm, whereas without strapping this parameter is equal to 740 mm. the Standard width of the floorboards - 200 mm, so only one unit needs to be cut lengthwise using a jigsaw. From the Board you should remove projecting spike that is done by plane. The mechanical part should make perfectly smooth, there should not be deformations and indentations. Once boards are done, they need to collect in one blade, thereby enabling an inspection. Timber strapping cut into 4 lines, two of which will have a size of 2000 mm, whereas the other two will be at 740 mm.

Bonding boards

Now we need to assemble the door (to the bath). With their hands and it's easy to do. The next step may be to glue together the boards for this, use white glue. The groove must be filled with a glue, cementing the corners of the elements of the clamps. During Assembly, the master is advised to use a wooden mallet to tightly connect the grooves. In the presence of the workbench canvas is on it manages to recreate the effect of the press for better bonding. Then the cloth is left for a few days for drying glue. Is then processed by planers. Note: to remove a lot of material is not necessary, it will be sufficient to treat the surface to become smooth, had splinters and ROE.

Tying of the canvas

When the door to the bath with his own hands, step by step, it is recommended to consider technology. Onthe next stage, it involves the tying of the canvas. Timber fixed to the ends of the screws, and the corners of the workpiece are bonded lap or tenon. Screws should be selected so that their length was greater than the width of the beam. Accessories should be shipped in boards 3 cm

In order to increase the rigidity, it is necessary to strengthen cross bar. If you produce the front door, the straps should be installed on the outer surface. Between them in the future will be able to place the insulation. If the door will share the room inside the two straps that are attached at the same distance from upper and lower body.

Final work

If the master decided to carry out the door to the bath with his own hands, step by step to consider the technology he will be able in this article. At the final stage you can start fixing accessories, namely, handles and door hinges. If the design will be placed inside, it is best to abandon the use of metal handles as they will be heated by the high temperature. It can cause burns. It is better to use wood products, which are safe in operation, and manufactured they can be by yourself. For finishing treatment of a cloth is best to cover the wood impregnation depth of penetration, the composition should be environmentally safe, does not allocate harmful substances and to protect the material from decay processes.

Door Installation

Setting the doors in the bath with his hands is thus to eliminate the tilt or misalignment of the racks, otherwise the door will open and close with tension. For racks it is best to use a 11-cm beam, the thickness of which is 6 cm Width of the uprights must be greater than the width of leaf: 7 cm Beam, it is recommended to prepare a game in it a groove in which is placed a door leaf. The gap between him and the box should be equal to several millimeters, as the wood will expand under the influence of humidity and temperature. As you can see, not so difficult to make doors for bath with his hands. The drawings you will be able to prepare independently or to borrow from the article.

By the Way, the doors can open outwards, while the strap should be placed there. This will reduce heat loss and minimise draughts.

If running the groove you noticed that it is too large, it is possible to apply silicon seals, which are located around the perimeter of the box. Fastening the last to the doorway is long anchors, the holes between the frame and the wall should be sealed with construction foam and decorate with trim. The door to the bath with your hands it can be hung when the box is completely ready. If the design is quite heavy, you should purchase a heavy-duty curtain in the amount of three pieces. Two of them are located on top of the web, while the third – at the bottom. In order to prevent unauthorized eat the door, one of the curtains fastened back, strengthening the findings weight.

The Manufacture of doors of the wagon

The Door to the bath of the lining with your hands you can be performed on the same technology that was described above, but the next step is the finishing of fabric material. This prepares the lining, the length of which should be a few more lines running at an angle of 45° from one long side to the other. The material is fixed with screws in the groove, the subsequent installation of all boards is carried out by the same method. The lining should not interfere with the binding, and trimmed the ends you want to hide. Each plank is numbered from top to bottom, after finishing parsed and trimmed with a saw on the drawn lines. Such work should be done on both sides of the door.

If you made a wooden door to the bath with his own hands, after cutting and finishing of the material you need to reinstall the trimmed workpiece into place, attaching to the fabric elements of the three screws in the slots at an angle of 45°. Extreme boards should be fixed on the top to harness hid their heads. It is important to avoid cracking of the groove, for this it drill the holes 0.5 mm larger compared to the diameter of the screw.

Finishing

The Door to the bath with his hands can be treated with sandpaper fine grain. It should go to all corners, eliminating surface irregularities and Kruglaya sharp edges. Some masters advise to use hand router, with which can effectively handle edge shaped cutters.

That the doors to the bath! With your hands you can decorate the design. For this canvas trim decorative straps, shaped materials and rods.

Conclusion

The Best option would be if the door you made from one sort of hardwood. It could be alder or basswood. The use of these materials is coefficient of thermal expansion, which affects the distortion products. When you run design of wood of the same breed will be able to achieve that deformationwill be lower. An exception may be only the case when the canvas runs from pine boards, and the rest of the elements – from Linden. The canvas will be closed by the sheathing from moisture and steam, so a coefficient of thermal expansion can be neglected.

Special attention is paid to quality of timber, which should not have through knots and defects. Their presence is permissible only in the case when wood is used for the manufacture of the door leaf, close finish. If in your Arsenal, no circular saw or router, replace these tools are a chisel and a hacksaw. But to make the door "on the knee" only by a true professional of his craft.