Insulation tube of polyethylene foam

Date:

2019-05-12 05:20:30

Views:

637

Rating:

1Like 0Dislike

Share:

Table of contents:

Insulation tube of polyethylene foam is a material which has high flexibility and resistance to various mechanical damage. This protection is not terrible effects of gypsum, gasoline, oil, and lime. The surface is able to endure the temperature of the coolant, which may reach 90 degrees. The insulation is the form of tubes, which are installed on the main pipe system by the method of simple tension. If pipe insulation is to be mounted on an already installed system, you will need to produce a special section along a longitudinal line. The resulting joints should be cemented with the help of designed for the purpose of composition. Due to the presence of longitudinal section of the tube has the ability to cut not only straight, but also quite simple, providing a quick and speedy installation. The excellent characteristics of the described insulation save on heating and to reduce the final weight of the structures, reducing the consumption of building materials.

Main features

insulation pipe

Insulation pipe is made by extruding plastic granules. In the end possible to obtain a structure which has a small closed pores. The material contains significant amount of air that provides the insulating qualities. The products have high elasticity and flexibility. Online you can find many sizes, whereas the length of the tubes is equal to two meters. The gray color of the tubes and throughout the length of the air slit. Insulation tube of the described type can be used for pipes made of steel and copper.

Purpose

pipe insulation termafleks

Products used to protect cold pipelines, which are located inside the building. The insulation in this case is the prevention of condensation. It should be noted that the latter phenomenon may cause shortening the life of the pipeline. Used insulation and freezer units, when there is a need to maintain extremely low temperature media. Quite often these products can be found in the regeneration systems, which are located inside buildings. At the same time the tasks also supports the preservation of the initial temperature. If insulation is used outside of buildings, it is able to prevent freezing. In addition, this material can protect a person from the possibility of receiving dangerous burns. Indoors operation is allowed without additional recommendations, while the outside set isolation must, protecting it from exposure to direct sunlight. The material may undergo impact -40 to +70 degrees. Humidity is allowed up to 100%. The temperature of the coolant in the conduit may vary in the range from -40 to +100 degrees.

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Advantages

pipe insulation k flex

If you want to use pipe insulation "Armaflex", then you can be sure that the material is absolutely hygienic and safe for human health and the environment. It is completely inert, does not produce dust and has no extraneous odor. You can use it in objects for different purposes, until medical establishments and buildings of the food industry. Insulation of this type is absolutely impervious to steam and water. It prevents mildew and resists rotting. To further protect the insulation does not need, among other things, it is capable of preventing corrosion and impact on pipes, concrete, cement, lime and plaster mixes. Pipe insulation "Armaflex" lowers audible noise and reduces structural sounds, which can arise in the operation of the system. To install the product simply, the economical work that is very like a modern consumer. Such isolation is characterized by durability, period of its activity is much higher compared to those possessed by the pipeline itself.

Installation considerations

pipe insulation energoflex

Pipe insulation K-Flex must be installed after the surface is cleaned from impurities, is represented by grease and rust. Work should only be performed on functioning equipment. To ensure de-energizing is required 24 hours before start of installation work. If necessary, you can make cutting, using a sharp knife. When laying it is important to ensure absolute tightness. To do this, use the special glue "energofleks".

Installation on an unspecified system

pipe insulation made of polyethylene

If you will use pipe insulation "energofleks", which is installed not yet installed the system, it is necessary to wear the tube on the tube. When welding, be sure to protect the material from Poplavok. After the seams have cooled, they should be cleaned and move them insulation material. The final step is the bonding of the insulation at the ends between them. Pair joints can be produced withusing construction staples. To provide additional sealing of joints, use duct tape. If the pipeline will be in the ground in the process of operation, it should be protected with a cover, to avoid damage of the elements of the soil.

Pros and cons

pipe insulation from foamed polyethylene

Pipe insulation polyethylene has a negligible coefficient of thermal conductivity, this indicates that the effective fulfilment of its tasks, the material is able to provide with a slight thickness. The described heater has a rather impressive mechanical strength to the tensile forces, therefore, after deformation the material well enough restores to its original shape. Use when mounting no need extra tools. As one of the important advantages of this insulator is the low cost, which is almost two times less in comparison with that which have analog materials. This makes polyethylene foam is cost-effective for work on large-scale pipelines. However, we can identify a single flaw. It is expressed in Flammability. This leads to the inability to use this insulation at facilities, which meet high fire safety requirements.

Specifications

pipe insulation rockwool

Pipe insulation K-Flex ST has a density which may vary from 25 to 40 kg per cubic meter. In addition, you can select excellent elasticity, which is stored to -80 degrees. This allows to use this material on any pipe, no matter what form they may possess. The highest load on the gap that can be absorbed by the insulation, is 0.3 MPa, wherein the insulation material has a dynamic elastic modulus, which is equivalent to 0.77 MPa. As for the compression ratio, which is stored at an external load, it is equal to 0.2. If you purchased the pipe insulation Rockwool, it is necessary to pay attention to the coefficient of thermal conductivity, as a rule, this figure varies between 0.035 W/MK. With regard to vapor permeability coefficient, it is equal to 0.001 mg/MCPA. It is according to this indicator, the described insulation can be attributed to the class of materials that are completely non-permeable. Pipe insulation made of polyethylene foam absorbs water in an amount of 1.5% of its volume after being in the water during the day. This figure increases by a few tenths with increasing time of exposure to water. Thus, if you place the heater for 28 days in water, it absorbed 1.9% of its weight.

Additional features

Material Thickness can vary from 6 to 20 millimeters. With the intermediate value equal to 9 and 13 millimeters. In the sale you can find a great variety of standards of the diameter of the sleeve, this parameter ranges from 12 to 200 millimeters. In industry the most commonly used internal diameter equal to 100 and 150 millimeters. In the production process in addition to foam reagent to the ingredients are added various additives, which are designed to give the end product the required characteristics, namely the elasticity and resistance. Regarding the latter, insulation is classified as moderately flammable.

Conclusion

If there is a need to prevent the occurrence of condensation or to protect the pipe from corrosion processes, it is necessary to use the above-described pipe insulation. By purchasing this material, you can not be afraid for what he will be capable to cause harm. This is because the insulation of this kind is made from organic ingredients. Owned for these reasons, in modern industry and in the improvement of private piping insulation is used, the above-described type which is inexpensive and has a truly outstanding qualities.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/32952-zalyacyya-trubavaya-z-vspenennogo-pol-etylenu.html

DE: https://tostpost.com/de/gem-tlichkeit/32623-isolierung-rohr-aus-pe-schaum.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/32501-el-aislamiento-de-los-tubos-de-espuma-de-polietileno.html

KK: https://tostpost.com/kk/domashniy-uyut/33276-o-shaulau-byr-k-b-ktengen-polietilennen-zhasal-an.html

PL: https://tostpost.com/pl/komfort-domu/34327-izolacja-rur-ze-spienionego-polietylenu.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/34113-o-isolamento-do-bloco-de-espuma-de-polietileno.html

TR: https://tostpost.com/tr/domashniy-uyut/29701-zolasyon-boru-polietilen-k-p-kten.html

UK: https://tostpost.com/uk/domashn-y-zatishok/33482-trubna-zolyac-ya-z-sp-nenogo-pol-etilenu.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

How to save water in the apartment: tips

How to save water in the apartment: tips

one day each of us begins to wonder about how to save water. We are talking not only about the reduction in the payment of utility bills, but about saving resources of fresh water on the planet. There are many tips and advice on r...

Aluminum radiators: types, features and reviews

Aluminum radiators: types, features and reviews

Comfortable (especially in the cold season) is impossible without proper and effective heating system. For this purpose, they often use invented in the 50-ies of the last century aluminum radiators. Their relevance at the present ...

Vents for metal: overview, types, features and reviews

Vents for metal: overview, types, features and reviews

arrangement of the ventilation through the roof, not to be confused with the regular exhaust of air. Of course, the traditional home ventilation may have access through the roof, but in this case it is the system of ventilation of...

The Foundation of the blocks. Properties and description

The Foundation of the blocks. Properties and description

construction of Foundation of concrete elements is the quickest option. Although solid surface is more appropriate for him, for example, filled with concrete, as is a monolith, but it will have to dry for almost a month, and all c...

What should be paint on concrete for outdoor use

What should be paint on concrete for outdoor use

Concrete pavement should be protected from negative environmental factors, as well as give them the properties of high resistance to contamination. That such requirements should match the paint on the concrete surface for outdoor ...

Glass tables for the kitchen: sliding design for every taste

Glass tables for the kitchen: sliding design for every taste

for quite a long time the furniture made of glass, never goes out of fashion. This applies to many different things. The kitchen of this trend is also not spared, and tables for kitchen, glass (sliding & solid) can now be found in...