Balancing stands for the tire. Specifications, prices

Balancing machines (balancing stands) are one of the main devices that are on service stations. They are intended for wheels of cars and trucks. This is directly the process of balancing can be done either statically or dynamically.

Drives the wheels is permitted. Modern balancing stands capable of working with steel and alloy models. To use the above equipment only indoors. Thus it is necessary to monitor the ambient temperature. Usually in the frosty time balancing benches can not be operated.

How the stands?

At the bottom of the stand wheel balancer (tire changer) has a built-in bar that is over the bed. The casing with the cells is above it. Next to the display are set screws, which are necessary for the operation of the processing unit. On the side of the device there is a lid shaft. Next is the large pulley, which rests on the spring.

The right side of the set equipment a set of cones, as well as quick focus. Under the motor of the balancing stand includes a brake system. For fixing wheel bolt provided and for centering there is a special finger. To adjust the position of the shaft, equipped with an elevating mechanism.

Important characteristics

The Main characteristics balancing stands are the acceptable limits of width and rim diameter. This takes into account the mass of corrective shipping. Additionally, manufacturers specify the rate of error in the weight of the wheel. Directly on the balancing affects the angle of correction which is measured in degrees.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Among other things, draws attention to the discharge of the digital indicator. Allowable weight of the wheel depends on the model stand. At the same time to set the working mode can be very different. The quality of work of the device is affected by the duration of the measuring cycle and the time of continuous operation. In turn, the power consumption of the network depends on the marginal frequencies. Overall dimensions of the device play an important role. Stands stand wheel balancer (tire changer) in an average of 3,500 euros.

Stands company, "Hofman"

Balancing stands wheel above brands are highly reliable design. In many models clamp set self-centering jaws four. Mounting lamp has a very movable. If necessary, its position can easily change. Among the shortcomings should be allocated only weak mechanisms of fixation. In this case, the velocity of the rim must be constantly monitored. In turn, the clips are recorded with a very large force. Overall the models are quite expensive and may not fit everyone.

Features "Hoffman 4500-2"

The diameter of the circular wheel in this model allows a maximum of 25 inches. It is possible to install it with the size of 8 inches. The width of the wheel in turn can commit no more than 20 inches. The average speed is 200 rpm. The measurement time is around 7 seconds. The device is powered from the mains with voltage of 220 V. the dimensions of this balancing stand is average. Assembled it weighs 130 kg. it will Cost the buyer in the market for about 3800 euros.

Settings for booth "Hoffman 3900"

"Hoffman 3900" – tire changer equipment, which is compact in size. The display is equipped with a large, and follow the basic figures are quite comfortable. When manually entering the maximum wheel diameter allowed is 30 inches. In turn, the width of the rim should be no more than 20 inches. If the wheel weighs more than 80 kg, set it on the stand it is impossible.

The Average speed of the balancing bench is 230 rpm. Operating measurement deviation is the system for 6 seconds. The weight of the stand assembled exactly 80 kg. of the features of this model, you can select a convenient programming. The input size of the wheel is automatic and doesn't take very long.

For precise positioning of the rim-the manufacturer developed a special measuring arm, which is connected by a clamping system. To select the load position has a special mode. In a single measurement cycle it is possible to carry out both static and dynamic balancing. To increase the maximum speed stabilizers are utilized. To set the load needle in this model is allowed, but in General there are 8 different programs to select wheels. After the measurements, the braking rim is made automatically. Additionally there is the option to manually stop the shaft by means of a pedal. Is this the balancer (the market price) 5,000 euros.

Balancing equipment "Hoffman 6300-2"

The Company Hofmann balancing stand 6300-2 power is 0.6 kVA, and the average frequency is around 50 Hz. The power source device is a network with a voltage 220 V. continuous workthe balancer is capable of 8 hours. The measurement cycle takes less than 10 seconds. In addition we should note the good time policy regime. This happens when the mass of the cargo is not more than 200 g for 30 seconds.

Rim Width max 350 mm is allowed, but at least you can balance 76 mm. the Parameter of the discharge of the digital indicator equal to 1 g, and the coefficient of mutual correction is around 0.1. In turn, the error of the angle setting is 3 degrees. Max has the ability to set the wheel weighing less than 60 kg. the Price of this electrical equipment is about 5500 Euro.

Features of the stand AET DST910B

The Balancer is DST910B equipped with an automatic turn of a wheel. Other features can distinguish easily enter main parameters. A complete measurement cycle of the device takes 5 seconds. The accuracy of the data is quite high. Maximum wheel width allowed is 20 inches and its diameter shall be not more than 30 inches. The average speed of rotation of the balancing stand is equal to 220 rpm. The rim can be fixed a total weight not exceeding 70 kg. this model Weighs in assembled exactly 150 kg. For cones in the system manufacturer provides a very comfortable cell.

In Addition it should be noted quality holder clamping device, and for freight there is a separate cover with the cells. Established a measuring program "Hitchhiking". Only model there are nine profiles of the operator. The braking rim after work is automatic, and manual stop has a pedal at the bottom of the device. The needle load can be set. To minimize the balancer program is "PAX".

In General, the course of the rim shaft is carried out fairly smoothly. To work with the wheels of the motorcycles in this model. Additionally permitted alloy wheels. In a single measurement cycle it is possible to conduct static as well as dynamic balancing. Cost this model the buyer of 6,000 euros.

Features of models ", Beisbart"

In General, many models of stands suitable for cars and trucks. The dimensions of devices can vary greatly. This is largely due to the diameter of the drive shaft. Additionally take into account the complexity of the control unit. As a rule, balancing benches above companies are equipped with 17 inch display. There is a nice visualization of the process with elements of 3D animation.

Among programs it is possible to allocate a self-calibration and diagnosis. Carry out static and dynamic balancing is possible. In many models is provided by the program for customization. Cover tables at the instruments there is a quite durable. She is very stylish looks, and overall design of the balancing stands are well thought out. Cost model on the average from 3,000 to 5,000 euros.

Features "Beissbarth MT 847"

To Serve this model can wheels weighing up to 65 kg. the average measurement time is 4 seconds. Enter the distance from the disk is carried out in automatic mode. Diameter wheels the maximum allowed 30 inches, and the average speed is 205 rpm. The size of the shaft in this design is 40 mm.

Standard kit includes the following: balancing stand (instructions included), calipers, a set of cones and a laser range. Additionally applied protective casing and hammer for lifting weights. The price for this model is around 3100 Euro.

Main parameters of the stand", Beissbarth MT 855"

Balancing machines (balancing stands) "Beissbarth MT 855" speed control measurements are 4 seconds. While rim may be installed on a model weighing less than 60 kg. Enter the width and diameter of a disk is carried out in automatic mode. Wherein the rotation speed is around 167 rpm. The diameter of the shaft in this design is 400 mm. the Maximum disk size allowed at 30 inches.

The Source of power for the balancing of the stand is a network with a voltage of 220 V, and the average frequency of the apparatus equal to 55 Hz. Precision balancing in this model is quite good. A set of cones in the standard set provided. There is also a protective cover with quick release nut. For lifting weights the manufacturer has installed special pliers. The lifting device is of the pneumatic type. The process of static balancing is automatic. In General, control is quite easy due to high-performance microprocessor. Mode self-calibration and diagnostic runs automatically at system startup. Is this model on the market 3500 euros.

The Balancer is "Beissbarth MT 857"

The Mass of corrective shipping the balancer (cargo)", Beissbarth MT 857" is 200 g. the maximum angle of correction of the device - 3 degrees. Coefficient of mutual influence equal to 0.1. Parameter discharge digital indicator is at level 1 g. Maximum wheel width allowed is 350 mm, and the rim can be mounted with a diameter of not more than 500 mm.

Time to set the working mode pretty fast. The duration of the measuring cycle depends on the mass of the wheel. Continuously the unit can be operated for 7 hours. To eat from a network 220 In the above-mentioned stand capable, the deviation allowed in 22 V. the mains Frequency is able to vary in area 51 Hz. The power of this unit is at 0.7 kVA. Dimensions this model has the following: height 1100 mm, width 1150 mm, depth - 1000 mm. the weight of the equipment assembled exactly 200 kg. the Price of the balancer (cargo)", Beissbarth MT 857" is around 3200 Euro.

Stands company "Phoenix"

Balancing devices of this brand are different lifting mechanisms. The calibration wheel is quite fast. Check entire system each time after switching on the device. It should be noted the reasonable prices on the balancing stands, and they stand at average in the region of 2,500 euros. Frequency models is 51 Hz. The average voltage is 220 V.

Dimensions of the balancing stands are the most diverse. The measuring cycle usually lasts for 20 seconds and the measurement time takes only 10 seconds. The rate of error is quite small. To adjust the angle of the wheels is very simple, there are a lot of modes for carrying out balancing.

Model "Phoenix 920 W"

This model has a totally unique technology for the measurement of the balance rim. To serve trucks. Input of distance and wheel diameter is automatic. The measurement arm equipped with a special clamping system.

In Addition, it should be noted ultrasonic sensor, which is quite accurate performs calibration of the device. The choice of position of cargo is carried out in automatic mode. Carry out the wheel balancing with motorcycles. However, there is a program for static measurement of parameters.

The Maximum wheel weight allowed 200 kg, and the diameter of the disk should not be more than 26 inches. The average speed is around 215 rpm. Working air pressure 8 bar is aged. Noise level this unit produces not more than 65 dB, and it is a balancing hardware on the market for about 2,500 euros.

Features of the stand "Phoenix FW 6606"

This model is equipped with a large LCD display for control. Among other things it is possible to note a convenient range for input parameters. All programs in this balancing stand has eight. Among them are the self-test and calibration quality. Protection from dirt in this model, the manufacturer installed.

The Shaft has a diameter of 40 mm, the tail is considerably lengthened to increase the torque. Cover cabinets are quite durable, and the package is standard. In General, this balancing hardware is versatile and suitable for different types of wheels, and it is on the market 3300 Euro.