Project of prefabricated houses using canadian technology

Date:

2018-03-21 22:24:11

Views:

401

Rating:

1Like 0Dislike

Share:

Table of contents:

Canadian home constructed of structural insulated panels, in recent time has acquired a huge popularity. They cost not too expensive and can be erected in just a couple of days. The advantages of buildings of this type refers primarily to durability and the ability to select the most convenient layout. Project of prefabricated house is made, of course, subject to certain recommendations.

What is SIP panel

Is this material a special “pie” consisting of a thick layer of polystyrene or mineral wool, having excellent teplosernaya properties, and two sheets of OSB, fastened on both sides. This design of the plates gives it truly unique properties:

  • Light weight. Under the house of SIP-panels do not need to hold too bulky, expensive and complicated in the construction of the Foundation.

  • For Ease in handling. to Cut structural insulated panels can be ordinary hacksaw. It often happens that the house owners even first, just put up walls made of this material, doors and Windows are then cut in all the right places.

  • Strength. the Roof of such houses can be assembled using any heavy materials.

project prefabricated houses

Such properties of the panels enable the building of them are very beautiful and comfortable prefabricated houses. Projects (photos of these buildings can be seen on the page) they are both complex and simple. Next, let's see what, in fact, the nuances should be taken into account in their design.

Compiling projects

Structural insulated panels — high-quality material, it allows you to build a solid prefabricated houses. Projects of such buildings, however, should be developed taking into account some rules. For example, the owners of the site should know that above the three floors, houses made of this material is not recommended. Otherwise, at the slightest violation of the technology in the next can occur more than serious problems. The sizes of the canadian panel have the following:

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

  • Width — 650-1250 cm;

  • Length — 2500 -2800 cm;

  • Thickness   from 110 to 270 cm

Typically, a project of prefabricated house developed with regard to dimensions of the selected panels. That is, the height of one floor can't exceed 2.5-2.8 m, and the length of the wall must be a multiple of the width of the panel. But with this rule and retreat. However, in this case panel, of course, have to cut. And that's extra work and loss of time.

pre-fabricated home designs

As the climate in Russia is pretty harsh for exterior walls choose a thicker panel — at 270 cm For the inner, you can get the stuff cheaper — at 170-200 see Partitions usually assembled from panels at 110-120.

What you need to know

Most Often in the modern market you can meet the panel, the design of which as an insulator is included polystyrene. Warm this material keeps well, but, unfortunately, is Flammability. Therefore, making the project prefabricated houses made of expanded polystyrene, particular attention should be paid to the observance of fire safety rules.

You Can also spend a little time to find a supplier of slabs with mineral wool. This option is structural insulated material found on the market less often, are cheaper, but in terms of fire safety is much more preferable.

Architectural solutions for houses of SIP-panels

The Project prefabricated houses of SIP panels in relation to the plan can be absolutely anything. This material is allowed to build buildings with any number of rooms, attics, balconies, terraces, verandas, etc.

Most Often made of structural insulated panels erected conventional rectangular house. However, nothing prevents the owners of the site to collect t - or U-shaped building.

The Number of Windows and their shape can also be different. You can make wide openings, narrow and long, tall, round or even polygonal. Any difficulties in case of choosing custom Windows can only arise in the selection of frames for them. Doors can also be cut absolutely any field.

projects prefabricated houses using canadian technology

What is a finishing material for walls to choose

Beautiful appearance — it's also something, what is the difference between canadian prefabricated houses. Projects of such buildings in terms of finishing can be arbitrary. In fact, the house of SIP-panels — the construction of the budget. The solidity of this building can be given, successfully picking up the outer skin. Very beautiful, for example, canadian buildings with wooden framing. Rich look and home, made of artificial stone. You can use this house and ordinary decorative plaster.

projects prefabricated houses under the key

But most owners of suburban areas choose to finish the canadian buildings lining. It may be an ordinary wooden Board or block-house. In the latter case, the house would look like chopped. Of course, you can choose for a building cladding and cheaper — siding or even sheet metal.

Communications

Of Course, the projects of prefabricated houses using canadian technology shall also include methods of laying different kinds of engineering systems. Stroebe, or something like that to breakpanel design is not recommended. Because they are including in the role of bearing supports for floors and roofs. So the wiring in these homes, as in wooden, usually pull up the top using the cable channels. To close the latter and to make the wall attractive using plasterboard, plastic panels or plywood. In exactly the same way — for the outer covering are held in the CIP-houses ventilation ducts, water and sewer pipes.

pre-fabricated home designs photos

As you can see, the particular complexity of this procedure as the preparation of drawings and plans of houses of SIP-panels is no different. However, if the owners of a suburban area decide to build a large residential building or structure is a very complex architecture, perhaps they should refer to specialists. Nowadays there are companies whose employees constitute the projects of pre-fabricated houses under the key, and also engaged in the Assembly of such structures.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/5810-praekt-hutka-zvedzenaga-doma-pa-kanadskay-tehnalog.html

DE: https://tostpost.com/de/gem-tlichkeit/5810-das-projekt-bystrovozvodimogo-zu-hause-nach-der-kanadischen-technologi.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/5816-el-proyecto-de-bystrovozvodimogo-casa-canadiense-de-tecnolog-a.html

KK: https://tostpost.com/kk/domashniy-uyut/5813-zhoba-bystrovozvodimogo-yd-kanadaly-tehnologiya.html

PL: https://tostpost.com/pl/komfort-domu/5815-projekt-bystrovozvodimogo-domu-w-technologii-kanadyjskiej.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/5810-o-projeto-bystrovozvodimogo-casa-sobre-a-tecnologia-canadense.html

TR: https://tostpost.com/tr/domashniy-uyut/5817-proje-bystrovozvodimogo-ev-kanadal-teknoloji.html

UK: https://tostpost.com/uk/domashn-y-zatishok/5814-proekt-shvidkomontovanih-budinku-po-kanads-ko-tehnolog.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Stool of wood with their hands: step by step instructions, drawings and reviews

Stool of wood with their hands: step by step instructions, drawings and reviews

to make a stool with your hands, do not need special skills. To carry out this type of carpenter works under the power of a man who has no experience. Besides, it is a creative process which will require minimal cost and will brin...

Classification of loads and supports

Classification of loads and supports

in the construction of buildings is very important to consider the impact of external factors on its structure. Practice shows that the neglect of this factor can lead to cracks, deformation and destruction of building structures....

Apple pollen beetle: description and control. Drugs from the Apple blossom weevil

Apple pollen beetle: description and control. Drugs from the Apple blossom weevil

every year a lot of annoying pests to gardeners, destroying crops, fruit bushes and trees. Affected plants are covered with spots, they curl the leaves, fall fruits. Apple trees and other garden plants susceptible to Apple pollen ...

Petrol inverter up to 3 kW: reviews of manufacturers

Petrol inverter up to 3 kW: reviews of manufacturers

Compressor power up to 3 kW are often used on construction sites. If necessary, you can connect and drills, plate compactors, saws. Devices of this type are suitable for use in private homes. In case of emergency power outage, the...

How to make a stool with his hands

How to make a stool with his hands

In our apartments every year becomes more and more pieces of furniture, without which we cannot do. To them, of course, includes the stool. Your hand made or store-bought, doesn't matter much. Its basic functions will not change. ...

Balancing stands for the tire. Specifications, prices

Balancing stands for the tire. Specifications, prices

Balancing machines (balancing stands) are one of the main devices that are on service stations. They are intended for wheels of cars and trucks. This is directly the process of balancing can be done either statically or dynamicall...