Lada Kalina: a noise with their hands

As the drivers, the cars VAZ never had a high level of comfort. The company has always produced utilitarian cars. «Lada Kalina» - one of those cars. The owners after some time of operation of these machines notice the flaws. Some of them – the high level of noise when driving, "crickets" of the noise of the plastic panels when driving. Some drivers are struggling with similar problems with music, however, is not the best way. In this situation, will help sound insulation «Kalina». After simple operations in the car will be noticeably quieter and more comfortable.

Why you need a car "Kalina" insulation?

Before you start work on obessmolivanie, it is worth considering what you need in the result. One owners important to the quality of sound radio, the aim of the other – to get rid of various "crickets" and scratches, others just need a more comfortable interior. Why is it necessary? From the target depends on the selection of materials for the process. You Need to remember that if you have insulation «Kalina» your own hands, do not just do it all. The process is divided into several sections – this is true on a limited budget. Usually work begins with the doors and then insulate the floor, trunk, engine compartment, sometimes – the roof.

Tools and materials

So, for work will need a building dryer – it is mandatory. Any other Hairdryer for these tasks is not suitable. It is also recommended to buy a stitcher roller – it is needed for compacting shumoizolyatsionnye materials. The cost is negligible, and the benefits quite large. Still you will need scissors and a solvent.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Shumoizolyatsionnye materials

The Correct selection of materials – that's half the battle. It is worth remembering that there are vibration damping materials, and noise. Each of them are designed for different purposes.

Vibroplast Silver

It is quite flexible and elastic material-it absorbs vibration. Is a self-adhesive sheets with aluminum foil. They made markings in the form of squares 5x5 cm – this simplifies the cutting of a single sheet. This Vibroplast does not absorb moisture and is resistant to the environment. Additionally, it has high anti-corrosion properties and characteristics of the sealant. Another advantage of this material is its easy installation in areas with difficult terrain. For installation it is not necessary to heat. Sheet thickness is 2 mm. the material should be used on the floor in the cabin. Not less important he's in the doors for vibration control of a roof, the side parts of the body, on the hood and trunk.

Vibration-absorbing material Gold

It has the same properties and characteristics as the product of the brand Silver. However, the thickness of its more. Hence, the characteristics of vibroplasty above.

"Bimast Bombs"

It is also a material that absorbs vibration. Insulation «Kalina» impossible without such kind of products. "Bimast Bombs" is a few layers – aluminum foil on the front side, the layer of bituminous composition and a layer based on a mixture of rubber.

For the installation of the specified material must be heated to a temperature of from 40 to 50 degrees. The vibration absorber does not absorb moisture and is considered among car enthusiasts and experts the best. Its efficiency is quite high. To use the "Bimast Bombs" is recommended in the process of audiopodgotovka speakers and bodywork. The thickness of the material – 4.2 mm. is Used to shield the front of the tunnel, on the wheel arch, in the area above the muffler and driveshaft.

"SPLEN 3004"

This is a sound-absorbing material. In addition soundproof qualities he possesses high characteristics of thermal insulation. It is convenient to install both on straight and curved sections. It does not absorb moisture, is not destroyed under the influence of the environment. Sheet thickness is 4 mm. Suitable for shield the front side of the cabin, wheel arches, tunnel and doors. Paste "Splan" on a layer of vibromassage material. Thus it is possible to shumoizolyatory doors, wheel arches. The material stuck firmly to the maximum, you should clean and degrease the treated surface. When gluing it is recommended to withstand temperatures from 18 degrees to 35 degrees – in this range the manufacturers guarantee high adhesion characteristics.

"Bitoplast 5"

It is sound-absorbing and sealing material – it is widely used to address the various squeaks and rattles in the cabin. "Bitoplast" is based on polyurethane foam with the adhesive and impregnation. The material is water resistance, does not decompose, has insulating properties and is well suited for vehicles «Kalina». Shumoizolyatsiya with "Bitoplast 5" is quite effective. Sheet thickness is 5 mm.

Noise reduction doors

The Technology of sound insulation in «Kalina» do not differ from those for other brands of modern cars. However, there are some features. The work begins with the dismantling of the doors. The surface should then be thoroughly cleaned and degreased – you can use white spirit. If the lower part of the door caused corrosion-resistant coating, not delete itneed.

Insulation «Lada-Kalina», with his own hands produce, in this case begins with the installation of anti-vibration materials. Must be cut from a single sheet suitable for the size of the part – the larger the piece, the better. When applied, it is recommended to heat the side with the adhesive layer of a Hairdryer. The material is pasted on the inner wall of the door and rolled up the tool. The next sheet is applied to overlap. Next, a second layer of paste already shumopoglaschayuschy material. It is recommended to use the "Plan" or "Accent" (the latter is more efficient). In the first and in the second case, the sheets already have adhesive, so the process of applying pieces will be easier and faster. In the same way as in the case of vibration, the sheet then can be cut into as large pieces – will need to cover the entire surface of the door.

Next, you should decide whether to close the technological holes. If you close them using vibration-absorbing materials, to perform a variety of repairs have to do slots. If the interior is ventilated through the doors, after sealing the holes the air just can't circulate.

When patching holes in insulation doors «Kalina» will be higher, which bonded to the third layer, however, is in most cases unnecessary. It is better to treat the door.

Sound Insulation of the door lining

The First layer is applied to the vibration insulating material. This will help to weight upholstery. In the future, it squeaks less. Then paste noise "Bitoplast" – it is much easier to work with. Also, it easily accepts any form. At the final stage, you need to paste over the surface of the "Modelines" – the so-called "Antislip".

Dashboard, dashboard

The car «Kalina» insulation front panel can be performed without removing it – dismantled just hanging items. To shumoizolyatory glove box, first glue the "anticipa" all the places where the glove box touches the panel. Then process all the internal parts of the box "with Bitoplast".

To work with salon plastic dismantle the Central tunnel, door racks, and side panels. All plastic parts are glued and a "anticipo" or "Bioplasma". Special attention should be paid to the clip.

The car «Lada Kalina» insulation dashboard was happening to her removal. Then modelina process and a mask and directly to the instrument.

When working on the center pad paying special attention to the electrical wiring and hydraulic systems. All wires must be wrapped with "antiscript" and secure with clamps. In each connector should be added hotmelt.

All parts are panels that emit a “cricket” and creaking, paste "anticipo" or modelina. So you can get rid of the annoying noise. Below the panel is not rattled, it is recommended to weight.

The Hood

For obessolivanija bonnet specialists recommend the use of any isolator, and "Accent", which is noise-proof material. Technology sticking – the same as for doors.

The Sheet then can be cut into pieces of desired shape and attached to places on the cowl. The first layer is bonded vibration-absorbing materials, and then move to acoustic. In the same way performed insulation «Kalina»-the hatchback, but only on the trunk lid.

Roof and ceiling

They are insulated to reduce noise from rain and in order to remove the squeaks. For this task it is recommended to use Vibroplast "gold" or "silver." It is very important that the ceiling was not too heavy – in the future the best way will affect handling. Next, glue two or more layers of "Spline". Here the Main thing-not to overdo it, otherwise the headliner just snaps into place.

Back doors

Insulation “Snowball” (station wagon or hatchback) also provides for the processing back a month. As materials you can use everything that was used during works on doors. Technology similar. First clean and degrease the surface, then dried, and after install the materials using the heat of the Hairdryer or the same without him.

The models of "Kalina" insulation is easy with their hands. All work is extremely easy if people even slightly know how to work scissors. It is not necessary to contact the salons that offers such services. It is expensive.

Be sure to complete the insulation of the body of the car – the result will delight you!