Brake pads VAZ-2110: how to replace?

Serviceable pads – a pledge not only your safety but also the safety of other road users. Excessive wear of these elements increases the risk of losing control of the vehicle and cause an accident. In order to avoid becoming a victim of its own negligence, it is necessary to systematically check the condition of the pads and time to change them. By the way, you don't have to contact the service center.

In this article we will discuss how to replace front and rear brake Pads VAZ-2110. But first let's deal with the signs of their faulty methods of diagnosis and selection of the appropriate model.

Construction and principle of operation of the brakes of the front wheels

Front-wheel “dozens” have disk design. It is based on:

• Brake disk;
• Caliper;
• Working brake cylinder with piston;
• Two pads;
• Fastening elements.

When we push the brake pedal, the fluid acts on the piston of the working cylinder and moves the caliper. Pads placed inside it, thus pressed against the brake disc causing the hub to stop the rotation.

How to understand that the front pads it's time to change

Every detail of Every mechanism has its own resources, after which it needs to change. Front Pads VAZ-2110 is no exception. Their resource, as stated by the manufacturer of the car is 10 thousand kilometers. But this is only under the condition of normal use. They often fail much sooner. Their fault they may say:

• Burning on the dashboard warning light;
• Decrease in efficiency of braking and "wagging" steering;
• Squeak, rattle, crunch when braking.

Someone, probably, will be surprised, but the front Brake pads VAZ-2110 have in their design wear. When they wear out more than normal, on the dashboard indicator lamp is illuminated in the form of a wheel. This is the first indication that it's time to change pads.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

If you are during braking will notice that the car begins to lose controllability and from the front wheels is heard, and extraneous sounds, it is also an occasion in order to diagnose the brake mechanism.

How to check pads

Test pad is to determine the thickness of the linings. This, of course, need to dismantle the wheel and disassemble the caliper or drum. Measurements are taken with calipers or an ordinary ruler. The thickness of the lining shall be not less than 1.5 mm. If the result of your measurements close to this value, hurry to replace the pads.

What are brake pads on VAZ-2110 to choose

Only the right choice of brake system parts will allow you to feel confident on the road. And there is no need to save. As for the manufacturer, then, as usual, preference should be given to the original. Front brake Pads VAZ-2110 go under the catalog numbers 2110-3501080, 2110-3501080-82 or 2110-3501089. Are these parts inexpensive – about 300 rubles. You can choose pads and well-known manufacturers of auto parts. They are more expensive (up to 1000 rubles), but the quality of them is much better.

In No case do not buy cheap copies from Asia. Not only that, they wear out twice as fast, their design is quite fragile.

Important: pads, both front and rear, are changed in pairs and always on both wheels of the axle! That is why branded spare parts are sold exclusively in a set of four products.

Required tools

So, if you have already purchased spare parts for replacement, be sure that hand you had the necessary tools and means. Among them:

• Jack;
• Brace;
• Liquid against rust;
• Medical syringe on 20 cubes
• The keys 13 and 17;
• Slotted screwdriver
• Pliers;
• Hammer and chisel;
• Pipe (gas) key.

Changing front pads

Replacing the front brake pads on VAZ-2110 as follows:

1. Put the Car on level ground. Fix the rear wheels.
2. We turn on the wheel bolts, poddomkratit body and disassemble the wheel. Wrenched the steering wheel to disassemble wheel until it stops.
3. Inspect the brake for mechanical damage.
4. Determine the amount of brake fluid in the reservoir. If it is full, using a syringe, bleed the fluid (30-50 ml).
5. Bring down the retaining ring with the bottom bolt of the caliper. For this we use a coil and a chisel.
6. Key 13 turns the bottom bolt of the caliper. Stick finger key on 17. If necessary, use a liquid rust.
7. Take out the bolt and remove the caliper.
8. Open the caliper and remove it from the Brake pads VAZ-2110.
9. On the back (inside) pad set wear sensor. Using pliers, bites off the wire going to it. Then rassadina sensor connector.
10. Install the new pads into the caliper. Be careful not to confuse. Inside there is a pad on which the sensor is installed.
11. If the piston interferes with the installation, “push”his projections with a pipe wrench.
12. After the installation of pads connected the sensor to the harness.
13. Assembly produced in reverse order.
14. Following this algorithm, replace pads on the other wheel.

Upon completion, do not forget to refill the brake fluid reservoir. Also check does the lamp come on on the dashboard.

The design of the rear brake

Rear Brake “dozens” have drum design. It includes:

• Working brake cylinder;
• Two pads;
• Parking brake;
• Fastening elements.

The Principle of operation of the rear brake next. When you pedal, the brake fluid acts on the pistons of the working cylinder. They are nominated and throw the pads in hand. Their linings abut in the working surface of the drum, causing it to stop the rotation.

The Hand brake is actuated by means of a cable and rod. We pull the handle, the cable acts on the thrust, she spreads her pads.

What you'll need to replace the rear brake pads

The first step is to buy the brake pads. When choosing them follow the advice given above. Domestic manufacturers of auto parts sell back Brake pads VAZ-2110 under the original offer 21080-3502090, 21080-3502090-00, 21080-3502090-55, 21080-3502090-90, 2108-3502090, 2108-3502090-80. It is advisable to purchase a set of springs: compression, and guides.

Tools required:

• Jack;
• Brace;
• Hammer;
• Wooden spacer;
• Wrench 8;
• Two wrenches 13;
• Liquid against rust;
• Long nose pliers.

Before How to change brake pads on VAZ-2110, don't forget to release the handbrake cable. Without it, given that they have no wear to set them in the drum you have is unlikely to succeed. Weakens the rope on the pit using two flat spanners 13.

Changing the rear pads on the “ten”

The process of replacing the rear brake pads the following:

1. Put the car on flat ground, immobilizes the front wheels. Turns the bolts need wheels.
2. Poddomkratit body, Unscrew the bolts and completely dismantle the wheel.
3. Using wrench 8, Unscrew the guide studs on the brake drum (2 PCs.)
4. With a hammer and spacers bring down the drum from the hub. If it can not be treated in the place he “sits” on a ledge of the hub with liquid rust.
5. Long nose pliers remove the guides (small) springs on both pads.
6. Using the same tool, tie rod and remove the first upper return spring, then lower.
7. Installed new pads and make installation of the mechanism in reverse order.

Be Sure to adjust the Parking brake!

As you can see, Replacing brake pads on VAZ-2110 – the process is very easy and does not take much time. Change them on time, and your car will always be obedient to you.