Restoration of ball joint. Repair, restoration, replacement of ball bearings

Date:

2020-01-28 01:00:14

Views:

501

Rating:

1Like 0Dislike

Share:

Table of contents:

Suspension Arm connected to the wheel center (hub) via a ball joint. Symptoms of failure of this node are: knocking while driving on potholes, "wagging" the car on a level road, uneven wear of rubber and squeak when you turn the steering wheel until it stops. For some reason the ball joint may fail?

Causes of ball joint wear

The Main enemies of the ball was always water and dirt. To get to the connection, they can only in case of wear dust boot - rubber cover, which protects the joint from external influences. He either wears out during use (dries out, cracks), or it may be damaged mechanically (e.g., during the repair of the suspension).restoration ball

The Period of work of the ball bearing varies from 15 thousand to 120 km. The indicator depends on the operating conditions of the car and the condition of the protective boot.

Self diagnosis

The best option to find the fault always remains a diagnostic stand for a HUNDRED. But to find their own damage is also possible. To determine the faulty ball joint on the ear will need an assistant who will rock the car from side to side until the owner listens to all the creaks and knocks that are coming out of suspension.repair of ball bearings

Check condition of ball bearings visually much better, but you will need a viewing hole or lift. The assistant holds the brake pedal, and the owner shakes the wheel. If there is a backlash, then a ball bearing need to change, or to save to try to recover.

Repair and restoration of ball joint

The Ball joint can be either collapsible (e.g., of domestic autos) and non-separable. Of course, repair the node, which can be disassembled into parts, much easier. Ball disassemble, disassemble and change worn-out parts. Typically, this polymer insert and boot. Then set the knot in place. Repair of ball bearings (collapsible) is over.

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

If the ball does not understand, or portable grinder support base, but after the repair to restore the structure by welding, or use a more humane method and pour the liquid polymer in ball under pressure.restoring the ball with their hands

Many people recommend to disassemble the support in any case for grinding ball axis or its replacement.

How to disassemble disposable

Before proceeding to the disassembly of the ball joint, it must be removed. To do this:

  1. Poddomkratit car and remove wheel.
  2. Gut-wrenching the wheel to the end.
  3. Remove the cotter pin from the nut with the pliers.
  4. Unscrew the nut and using a suitable puller, press out the axle.
  5. Turns the ball mount.
  6. Using a crowbar press the bottom lever, and ball.

Now you need to disassemble the prop. If it consists of two brewed cups, the one of them you need to drill a few spot welds, and then chisel these cups to share. Then the housing is inserted finger with liner, and Cup-halves are welded together. Should ensure that the liner does not get overheated.equipment restoration of ball bearings

If the housing is inserted in the bottom, then flared edge brushes for a grinder or sandpaper. Then hit the end of the axle with a hammer to knock the bottom. Measure outer and inner diameter of the housing and ring made of steel with a height of 10 mm with threaded and tube. It is welded to the stand housing. Put your finger with liner and screwed the tube to the liner was running out. In the ring drill a hole of 2 mm as close to the tube and zaspirtovannaya it.

To install the ball stud into place, you must:

  1. Attach the ball to the lower arm and lock it.
  2. Install the pin (axle) into the slot, depressing the lower lever.
  3. Clamp the nut on your finger.
  4. If the finger is rotated at the landing, with a tire iron should pull the lever up.

When you install the supports in place, the puller is not required. Re-remove and install ball will be easier if you replace sportovcu on self-locking nuts.

Method of applying the liquid polymer

In commercially available ready-made rods filled with liquid polymer for restoration of ball joints with my hands. A polymer composition especially designed for nodes with high load. It can withstand pressure of more than 1000 kg/cm2 And dampens friction. Not affected by lubricants. Ensures the recovery of the ball joint and its operation of about 100 000 km. To use this method of repair can be several times.

The Technology of this method is quite simple. Using the extruder with pneumatic force, the polymer is injected through a special hole in the body of the host. He fills the emptiness inside, repeats the contour of the finger support and accepts all of the load.

The Machine for repair ball joints

In Order to properly perform work on the restoration of ball joint, you need to use the machine. It is designed to measure the temperature of the polymer and its correct submission to the body ball.press for recovery of ball bearings

The Standard tool for the reconditioning of ball bearings consists of:

  • From the blockupravlenia;
  • Extruder;
  • Compressor;
  • Pneumocylinder;
  • Termokeramika;
  • Multiple nozzles-adapter;
  • Polymer.

The Extruder with the polymer inside bolted to the cylinder. Worn-out anvil make a threaded hole and is inserted into a nozzle adaptor required size, which is connected to the extruder nozzle.

After the polymeric material becomes soft, start the pneumatic cylinder, which pushes it through the plunger and the nozzle support. In the case when the material is filled in incorrectly, the ball will last about 30 000 km.

It is Worth considering that overheating of the polymeric material takes all the necessary properties. Therefore it is necessary to read carefully the attached instructions and monitor the temperature regime according to the testimony of the machine.

Equipment for the restoration of ball bearings can be designed independently: the extruder to make on a lathe, and the remaining part to buy at the hardware store.

The Only reason why this technology cannot be used, is corrosion and mechanical damage to the metal structure. In this case, no restoration of ball joint is not subject and, accordingly, further operation too.


Article in other languages:

AR: https://tostpost.com/ar/cars/19775-restoration-of-ball-joint-repair-restoration-replacement-of-ball-beari.html

BE: https://tostpost.com/be/a-tamab-l/32456-adna-lenne-sharavoy-apory-ramont-adna-lenne-zamena-sharavyh-apor.html

DE: https://tostpost.com/de/autos/33044-wiederherstellung-der-kugelst-tze-reparatur-wiederherstellung-ersatz-k.html

ES: https://tostpost.com/es/coches/33260-la-recuperaci-n-de-la-r-tula-la-reparaci-n-la-reparaci-n-el-reemplazo-.html

HI: https://tostpost.com/hi/cars/18021-restoration-of-ball-joint-repair-restoration-replacement-of-ball-beari.html

JA: https://tostpost.com/ja/cars/20478-restoration-of-ball-joint-repair-restoration-replacement-of-ball-beari.html

KK: https://tostpost.com/kk/avtomobil-der/32100-alpyna-kelt-ru-sharly-t-rekter-zh-ndeu-alpyna-kelt-ru-auystyru-sharly-.html

PL: https://tostpost.com/pl/samochody/31403-przywracanie-kulowy-podpory-naprawa-regeneracja-wymiana-przegubu.html

PT: https://tostpost.com/pt/carros/31431-a-recupera-o-de-uma-jun-o-de-esfera-conserto-o-reparo-a-substitui-o-do.html

TR: https://tostpost.com/tr/arabalar/35310-kurtarma-k-resel-destek-onar-m-restorasyon-yedek-top-destekleri.html

UK: https://tostpost.com/uk/avtomob-l/31490-v-dnovlennya-kul-ovo-opori-remont-v-dnovlennya-zam-na-kul-ovih-opor.html

ZH: https://tostpost.com/zh/cars/17118-restoration-of-ball-joint-repair-restoration-replacement-of-ball-beari.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

"Mitsubishi Lancer 11": description, specifications, pictures and reviews

"Mitsubishi Lancer-11" – the updated model presented by renowned Japanese automaker in 2017. The car belongs to the class of Compact Cars, has a modern, rapid design and powerful propulsion systems. A highlight are the four-...

Manual transmission: the device and working principle

Manual transmission: the device and working principle

currently, almost every modern car is equipped with automatic transmission, which each time becomes more difficult. And, despite the fact that these units are significantly superior to a manual transmission, the latter has its adm...

As a startup, to put on the car, instructions for setting up

As a startup, to put on the car, instructions for setting up

the function of remote engine start systems in modern car alarm is almost mandatory. If recently, this module was equipped with only premium telematics kits with feedback, today and simple budget models offer a similar opportunity...

"Audi 80" (B4) - which engine is better? Specifications "Audi 80" (B4)

"Audi 80 B4" is a German mid-size vehicle manufactured from 1991 to 1995. During this time we developed and produced several versions of this model, differing powerplants and equipment. Before find out which engine "Audi 80 B...

Protective polishes 3M is the types, manual, description and reviews

Protective polishes 3M is the types, manual, description and reviews

To handle vehicle body car owners choose high-quality materials, based on the recommendations and advice of experts. The main functions of a good polishing paste — protection of the car body, the fight with scratches and oth...