If creaks laminate, what to do? Indiscriminately design how to solve the problem?

Laminate is one of the best of all materials, intended for floor tiling. This coating looks very impressive and solid, and also long serving. The advantages of laminate flooring include including simplicity of installation. Often the owners of apartments and country houses edit this stuff even with their hands.

Typically, after installation no problems with the laminate does not occur. However, sometimes it happens so that this coating starts to creak. What might be the causes of such problems and how easiest to eliminate? The remainder of this article will deal with why creaks laminate. What to do (without analysis and with the analysis of the coating) in this case, you will learn all the details from the article.

Main causes of problems

Laminate – material, unfortunately, quite capricious. The coverage of this kind can lie on the floor without causing their owners any problems, for decades. And can manifest itself in a few days after laying. If when walking on the floor boards began to emit annoying sounds in the first place, of course, you should find out why laminate flooring creak. What to do no parsing or analysis of the coverage in this case? The answer to this question just depends on what exactly was the reason for this unpleasant phenomenon.

Squeak laminate in the room maybe because of:

• Violations of the put technology in the preparation of base;
• Too thick or thin substrate;
• The lack of a temperature gap between the floors and walls;
• Poor quality of the material itself;
• Aging sub-floor.

Violation of technology of preparation of the grounds

Often it happens that the room is only in one place creaks laminate. What to do indiscriminately or with the analysis of the coating in this case – this will be discussed below. First find out what could be the reasons of such a difficulty. The appearance of the annoying sounds only in one place often means that during the installation of the coating were not observed technology training base.

Recommended

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Before laying the laminate floor in the compulsory level. Use or cement mortar, or a special blend. Defects in the base under the laminate cannot keep. If you step on a block located above the draft hole in the floor, it will SAG a bit. As a result, the elements of the tool joint will move relative to each other. And, as a consequence, you will hear the creaking. Measures in this case you need to take immediately. Otherwise, after some time, the tool joint will break and the coating will appear very noticeable gap.

How typically align the base

It would Seem that in order to get rid of the difficulty, which arose due to violations of technology of preparatory works, just need to remove a few slats to eliminate the existing defects and to set the material in place. But in practice, unfortunately, all is not so simple. The fact that the removal of the boards on the inside cover, and directly on its area impossible. This is due primarily to the peculiarities of the design for the slats. Therefore, the appearance of annoying sounds even only in one place coverage usually have to be disassembled almost completely (from the wall to the most problematic of the Board).

Creaks laminate: what to do and how to solve the problem without disassembling the cover

The Dismantling of the floor – the operation is technologically quite complex and costly. The fact that the laminate (and in particular the system Lock) the locks are very weak. And therefore, performing disassembly without loss of material fails almost never.

That is why the owners of apartments and houses, it often is almost a panic in that case, if creaks laminate. “What to do indiscriminately?” - I begin to wonder, almost all the owners of the property. Anyway, on specialized forums it is possible to hear quite often. And the answer, of course, exist.

So, how to avoid unnecessary costs if creaks laminate? What to do indiscriminately (irregularities also have to be addressed somewhere, and under the boards)? It turns out that to get rid of the squeak in one place laminate floor is possible only with the help of PVA glue and a large medical syringe.

The Board previously distressed using a hand drill drilling the hole. Next to it a syringe is injected the glue. Once the substrate is saturated and PVA will begin to protrude out of the hole, the operation is terminated.

What is drilling coverage

So in the problem Board need to drill a hole and fill it with glue in the case that creaks laminate. What to do indiscriminately coverage and how to correct the problem of uneven Foundation so we found out. Now let's deal with how to perform this procedure for all rules. And to begin with, find out what is the technology of drilling holes in the laminate.

Unfortunately, it often happens that when carrying out this seemingly very simplesurgery, on the Board there is a big ugly chip, to disguise which further difficult. Or the Board simply crack. In order to avoid such troubles, before drilling, care should be taken to select an appropriate tool. That is the drill you need to properly equip. Laminate, like wood, are best suited twist drill bits made of hardened steel. And choose should not their standard option with a sharpening angle 118°, and more acute. Otherwise, during operation the drill will be deflected and in this case the risk of chipping or cracking is greatly increased.

Something to close the hole

Done with a sharp drill hole from the syringe in the next phase squeezed PVA glue in the case that creaks laminate. What to do and how to fix indiscriminately covering this issue, therefore, is clear. However, after conducting a not too complicated procedure from the owners of the apartment there is another legitimate question: “How to conceal drilled the hole in the floor?” this can be Done using:

• Putty or sealant;
• The special wax pencil;
• Epoxy;
• Self-adhesive film;
• Polish.

At the final stage of the laminate need to be carefully removed with a clean cloth excess masking material and be very careful to handle the repaired section of fine sandpaper. Then part of the Board closed the hole should be polished with a cloth and cover with one layer of clear Matt varnish.

Creak due to temperature gap

So, we found, if only in one place creaks laminate, what to do indiscriminately. Causes of annoying sounds, however, may lie not only in the surface irregularities. Sometimes the creak occurs not all in one place coverage, and immediately over the entire area. There is such a problem for the owners of apartments and houses is most often due to the fact that when laying laminate was left too narrow a gap between the end boards and the walls.

Coverage of this variety like wood, with fluctuations in room humidity or temperature may grow or shrink. Therefore, the perimeter of the walls when laying laminate flooring and gets a small gap. Its width depends on the area of the room. If the clearance is too small, while extending the coverage in his column, there is a voltage. As a result, the elements of the locks start to push each other, and that becomes the cause of the creaking.

To Fix the problem in this case is also quite simple. For this you need to remove all baseboards. To actually increase the temperature gap to the required width using the angle grinder. Of course, to do this work properly.

How to cut coating

Next, let's deal with what to do if not enough wide temperature gap creaks laminate. What to do indiscriminately (the problem is solved by sawing the “excess” part of the boards) – in this case, it is clear. But how to reduce the coverage area by a few inches and not damage the Board?

Laminate-a material composed of several layers. So on the grinder should be put on a disk with as small a cutting structure. In this case the line of the saw cut will be very smooth.

Instead of the grinder you can use a jigsaw. For this tool, of course, you also need to choose the right nail file. Otherwise the cut will turn out sloppy. In this case you can use as narrow a blade for metal with fine teeth and a special, designed to work with laminate.

Elimination of other causes of difficulty

So, you now know if creaks laminate, what to do indiscriminately (irregularities can be eliminated with white glue, and the temperature gap to expand with grinder) coverage. But, of course, annoying noises can occur due to violations of technology of preparation of sub-floor or stacking of the boards themselves. The causes often are: poor quality of the laminate, the mismatched substrate or the aging of the sub-floor.

In all these cases, to do without dismantling the cover, of course, will not succeed. Poor quality laminate or unsuitable substrate will have to change. If the cause of creaking is the aging of the finished floor, you will need to perform even more complicated operation. In this case, you will not only have to remove the laminate, but also to dismantle the leveling screed. Squeaks in floor rough appear mainly due to the departure boards from a log. Consequently, to get rid of annoying sounds, they will need to knock out nails or fasten tightly with screws.