Calculation of artificial lighting. Street lighting. Calculation of lighting in industrial premises

Date:

2018-03-20 07:37:26

Views:

1132

Rating:

1Like 0Dislike

Share:

Table of contents:

In ancient times light was seen as a phenomenon that depended on the will of the Supreme beings of… Today, for anybody not a secret, how you can control this radiation, what is its essence, how to calculate the artificial lighting.

The Lack of light rays leads to a significant decrease in performance, deterioration of health and decrease mood. In this regard, the important point is correct, with the observance of hygienic requirements, the placement and connection of lighting devices. For enterprises profitable to purchase energy efficient equipment for internal premises and territory.the calculation of artificial lighting

Lighting Features

In range of wave length of 380-780 nm in the electromagnetic radiation of the optical spectrum becomes visible. It can be described by the following variables:

1. Luminous flux (it is part of the optical radiation perceived as light). The unit of measure is lumens. In the calculations is denoted as F.

2. The power light (the light flux density in the space lying in the direction of the axis of the solid angle). Is denoted as I,the calculation of industrial lighting and is measured in Candela.

3. The solid angle (part of the space, which is located inside the conical surface). Measured in steradian. Denoted in the calculation of W.

4. The illumination shows the value of the surface density of the luminous flux. Its unit is Lux, and is denoted by E.

5. Brightness represents the surface density of luminous intensity of a surface that lies in this direction. This flow is measured in candelas per square meter and is indicated by a L.

6. The rate of blinding (R) is a measure of glare lighting.

7. The criterion of illumination pulsation (CP), measured in percent, is used to estimate the relative depth fluctuations of light.

8. The discomfort metric (M) is used as the evaluation criterion of the uncomfortable glare that causes the feeling of pains in the eyes when non-uniform placement of the bright spots in field of vision.

Instrumentation

To determine light use different light meters. For example, the device “Yu-116" allows you to calculate this parameter is generated by incandescent and natural light. Luxmeter is used to control the illumination in agriculture, transport, industry and other fields.

Recommended

Calculation and payment of sick leave

Calculation and payment of sick leave

Sick Pay provided by the legislation of the Russian Federation, in particular TC and FZ No. 255. In addition, some rules are governed by the provisions of the civil code. Any employee upon the occurrence of a certain disease should contact a health f...

Employee certification for compliance with the post: purpose, procedure, result

Employee certification for compliance with the post: purpose, procedure, result

Employers perceive the order of certification of employees as a formality. Regulations intended for commercial organizations, were not issued. Certification is required only for employees of the organizations designated in the laws of the spheres, le...

Registration of vehicle: procedure, sample application, certificate

Registration of vehicle: procedure, sample application, certificate

Every person who buys a car needs to do its registration in the traffic police. It is necessary when purchasing new or used cars, as well as no matter whether the seller of natural persons or legal entities. Check the vehicle is in the traffic police...

To measure other quantities, e.g., brightness, ripple factor, use of analog-to-digital devices. An example of them is the pulse meter “ARGUS-07”. The principle of its action in the conversion of the light flux, which is created of extended objects in continuous electrical signal proportional to light. Then it is converted to digital code shown on the electronic scoreboard.

Types of lighting in production

If the room is illuminated only by lamps, floor lamps, lamps, the artificial light, the lighting is artificial. It is necessary to create comfortable working conditions, the normal operation of buildings and grounds. It can be divided into the following types:

  1. Rabochee.
  2. Ohrannoe.
  3. Avariynoe.
  4. Diurno.

First used for illumination of offices, places of work outside the building. The second and fourth type of coverage included in hours, and the third allocates the emergency exits, various safe points. Artificial lighting can be General, in which lamps are placed evenly in the upper zone of the office, or a combination. In the second case, the total is added to local illumination, which is created lamps that are close to the workstation location.

calculate lighting of the shop

The Following types of industrial lighting is natural. Here too we can distinguish several types: side, top, combined. First – when the sunlight enters the room through light apertures in external walls. At the second light to pass through openings in the walls in places of difference of heights of the building and through the lights. The third type combines top and side lighting. This kind of lighting is particularly necessary in rooms with permanent presence of a large number of people.

Combined type of lighting is a combination of natural and artificial. It is used in special cases, when the work is done from the first to the third digits, if you need space-planning solutions for the construction, or when economic feasibility is confirmed by the calculations.

Rules of types of illumination

When selecting parameter values, norms need to rely on the SNP “Natural and artificial lighting”. The lighting is adjustable, its minimum permitted level, based on the characteristics of accomplished visual work (RR). There are three types of SP:

  1. The First includes activities that do not need to use optical devices. The object of the discrimination in this case may be located at different distances from the eye.
  2. The Second allows the use of optical devices during the execution of works. The reason lies in the very small size of the object which is not perceived by the eye.
  3. Third includes work withwhich you want to receive the information from the screens. This type apply the special requirements of the lighting.

In coherence with SNiP “Natural and artificial lighting" we can distinguish the following characteristics of the visual works without using optics: discharge, podnasrat. The first is due to the size of object of distinction, and the second from a combination of contrast and brightness of object of distinction with the background. For each characteristic normalized light, indicator light, ripple factor and its methods of calculation of artificial lighting.

If the lighting in the room is natural or combined, to the category ZR is the coefficient of natural illumination. It represents the ratio of natural light to the set value of the external horizontal illumination, which is created by the light of the open sky.

When natural light is lateral and unilateral, there is a minimum value of Keo at the point located at the intersection of a vertical plane cross-section of the spaces and conditional functional surface at a distance of 1 m from the wall, furthest from the skylights. If the lighting is top or combo, then the calculations use the average value of the coefficient at the points located at the intersection of the vertical plane of the section of the room and work surface.

Calculation of artificial lighting

SNiP natural and artificial lightingThe First item in this issue is the selection of the type of light source. It is also necessary to determine the system light and the corresponding norm. The second paragraph will be hosted at the office of the selected lamp and the calculation of illuminance at specific points. And finally, the last point will be the definition of the power unit of lamps. The choice of light source is performed according to the following rule: economical discharge lamps are used in premises with air temperatures above ten degrees, with high demands on the quality of the color and the minimum degree of traumatism. If the office is natural light is absent and performs accurate work, used fluorescent lighting. If you want to use and to calculate led lighting, it should be remembered that lamps of this type do not bear a stroboscopic effect, that is, the light goes on constantly. Therefore, it is important to hold the correct calculation of ripple factor to exclude high brightness.

When defining a lighting system it is necessary to consider the efficiency of the combined system light as well as his hygiene (the uniformity and brightness of the light flux). When the equipment in the office is uneven, apply localized lighting. The definition of the type of lamp needed to be subject to the rules to the scattering of brightness in the field of view of employees, and depending on the condition of the air environment.

For a clearer distribution of light created the lighting scheme. It is of several types: simple (connect to a small number of lamps connected to one switch), selector (connecting two independent groups of light sources that are controlled at one point), bidirectional (on and off is carried out from two points) switchboard (controlled by two switches in two directions, and one - on-one direction).

calculate lighting of industrial premises

Calculation of the lighting plant should consider the following parameters: determination of type of light sources and luminaires, their counting and the proper distribution in space, determine their power and the power supply circuit. In addition to these points, it is necessary to pay attention to the types of visual tasks, environmental conditions, how is the working equipment, number of employees, emergency lighting.

Method power density

Calculation of artificial lighting in this way allows for tentative calculation of lighting of industrial premises with a uniform distribution of lights. The power of one lamp is calculated as follows:

Pl = PyS/PL

Where Ru denotes the power density of the lamp, the value of which are in directories. The power density depends on the type and placement of lamps and lighting fixtures, the characteristics of the illuminated space and the height of the suspension. The value of S shows the area of the floor, and PL – the number of lamps. The results are usually rounded off in the direction of greater value.

Method of the luminous flux or efficiency

This method is the calculation of industrial lighting in cases where the illumination of the working area are set. Method does not apply for localized topical and local lighting if the working surface is not horizontal and also in the calculations of directional concentrated light flux.

The Calculations are made according to the following formula:

F = Z K En S/ Nη

Where F – luminous flux; En – normalized illuminance; S – floor area; N-number of lamps; Z – minimum power factor; K - factor of safety; η – the utilization of light rays of the lamps.

The value of the luminous flux of the lamp is selected, which may differ from the calculated values in the range from -10 to +20 percent. If the difference is greater than the allowed boundaries, it is governed by the number of lamps.

Pointmethod

Method used to determine the light rays of the lamps in cases when reflected light is not important. The method used in any location of the illuminated surface and fixtures. The method is based on the ratio dependence of the light surface (E), which creates a point source of light, the distance to surface (r), angle of incidence (a) and intensity (I):

E = I cos α/r2

Calculation of the lighting Department, and specifically the lighting installation includes several stages:

1. Finding the minimum of the normalized illumination.

2. The selection of the type of light source. The definition of the type of fixtures and their placement in the shop.

3. The selection of control points with the least conventional illumination on the plan.

4. At the test points carried out the calculations of conditional light. Subsequent calculation of lighting in industrial premises is based on the point with the lowest conditional light.

5. Using reference tables to determine the coefficients of the added light and headroom.

6. Find the luminous flux of the lamps. According to the results select a standard bulb.

7. Determine the lamp power and all the light installation.

Example of lighting calculation present the following: the purpose of this height h=4 m, the safety factor k=1,5, the ratio of incremental illuminance, u=1,2, the normalized illuminance Emin=75 Lux. You need to define the lighting with working surfaces at the walls of the lamps DFC.

As in the lamps of this type deep distribution, λ=1. The distance between light units is 4 m and the extreme lighting of the walls is 1 m. Placed on the plan control points a And B (with minimal light) and compute the distance from the nearest projection of the lamps (d). The next point is the defining condition of illumination and the position of the point with the least light. According to the counted value of the luminous flux of the lamp, its difference with the standard value, and find the light.

Calculation of General lighting when working with computers

methods of calculation of artificial lightingWhen the activity of the employee connected with the PC, should be observed a special rule when installing lighting. In this case, the eye is experiencing a double burden, as perceives the reflected light from the keyboard and documents, as well as direct from the monitor.

The Room must have natural and artificial lighting, with the Keo coefficient is not below 1.2%. It is necessary that the working surface with computers was oriented to the side light-openings for the penetration of natural light. Calculation of artificial lighting relative to the common uniform incidence of light. Direct bestcost is limited from the sources of illumination (the brightness of the Windows, lamps and other luminous surfaces is not more than 200 CD/m2 ) and mirrored regulated by proper choice of fixtures and positions of the functional areas depending on the basis of light (brightness, glare on the screen no more than 40 CD/m2 ).

Artificial light as the light sources need to use fluorescent and compact fluorescent lamps. If the premises are industrial or social character, it is possible to apply metal halide lamps. The lamps should be with louvers and lenses.

Solutions street lighting

Street lighting carries the important task of uniting the outer parts into a single whole, plays the role of assistant safety and orientation in space and adds an aesthetic touch to the decoration of the cities. Lighting equipment for this type of lighting is necessary to choose depending on the features and status of objects. They can be activated automatically or with the Manager. We can distinguish several types of street lighting:illumination

  1. Flood. The method to install and aiming of floodlights flood lights. It is used for illumination in surveillance of the surrounding areas.
  2. General. This method involves a uniform distribution of lamps of the same type. It is ideal for lighting paths, parks, areas where people go about their business and cars.
  3. Marking. The street lighting fixtures located along selected lines and shapes. It is used to create visual outlines, underlines, bump, highlight areas of road and pedestrian paths.


Article in other languages:

AR: https://tostpost.com/ar/the-law/10332-calculation-of-artificial-lighting-street-lighting-calculation-of-ligh.html

BE: https://tostpost.com/be/zakon/18555-razl-k-shtuchnaga-asvyatlennya-vul-chnae-asvyatlenne-razl-k-asvyatlenn.html

DE: https://tostpost.com/de/das-gesetz/18567-berechnung-der-k-nstlichen-beleuchtung-die-stra-enbeleuchtung-berechnu.html

ES: https://tostpost.com/es/la-ley/18582-el-c-lculo-de-la-iluminaci-n-artificial-el-alumbrado-p-blico-el-c-lcul.html

HI: https://tostpost.com/hi/the-law/10338-calculation-of-artificial-lighting-street-lighting-calculation-of-ligh.html

JA: https://tostpost.com/ja/the-law/10339-calculation-of-artificial-lighting-street-lighting-calculation-of-ligh.html

KK: https://tostpost.com/kk/za/18553-esepteu-zhasandy-zhary-tandyru-k-shen-zhary-tandyru-esepteu-zhary-tand.html

PL: https://tostpost.com/pl/prawo/18527-obliczanie-sztucznego-o-wietlenia-o-wietlenie-uliczne-obliczanie-o-wie.html

PT: https://tostpost.com/pt/a-lei/18525-o-c-lculo-da-ilumina-o-artificial-a-ilumina-o-p-blica-c-lculo-de-ilumi.html

TR: https://tostpost.com/tr/hukuk/18561-hesaplama-yapay-ayd-nlatma-sokak-ayd-nlatma-ayd-nlatma-hesaplama-retim.html

UK: https://tostpost.com/uk/zakon/18549-rozrahunok-shtuchnogo-osv-tlennya-vulichne-osv-tlennya-rozrahunok-osv-.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Methods and subject of criminal law

Methods and subject of criminal law

the Original meaning of "criminal law" of its origin, the scientists explained in different ways. However, researchers share a common view on two main components: the concept of crime and punishment. In modern society th...

Passport stolen - what to do, where to go? Sample statements to the police about the theft

Passport stolen - what to do, where to go? Sample statements to the police about the theft

If a person's passport was stolen, it will give him a lot of trouble and inconvenience. Of course as soon as possible to get rid of them, you need to go to the police and write a statement. The procedure delay is not worth it. Oth...

Declaration of fire safety. Declaration of fire safety organizations: sample

Declaration of fire safety. Declaration of fire safety organizations: sample

the Declaration of fire safety was introduced by the Federal law №123. This document allows the owner to determine in the framework of the law requirements on construction and work instructions. We next consider how the Declaratio...

Article 157 of the criminal code. Malicious evasion from payment of means for the maintenance of children or disabled parents. Article 157 of the criminal code: comments

Article 157 of the criminal code. Malicious evasion from payment of means for the maintenance of children or disabled parents. Article 157 of the criminal code: comments

In the domestic legislation establishes the obligation of parents to support minor children. In the event of a divorce, one of them must pay alimony. a Similar duty is provided for able-bodied adult children to their disabled pare...

The change of essential working conditions: order, sample order

The change of essential working conditions: order, sample order

the Heads of some companies, choosing new ways of management immediately undertake to implement them. While the legal aspect of the implementation is often limited to issue an order that the payment system will now be so-and-so, a...

Extract from the egrn - what is it, why, where and how to get it

Extract from the egrn - what is it, why, where and how to get it

Very important document is the statement of the egrn. What is it? How does this help? Where can I find that? The answers to these questions of interest to many. In fact, to issue a statement egrn not so difficult. Let's consider s...