Engine KAMAZ 740: device and repair

Date:

2019-12-01 00:20:12

Views:

2274

Rating:

1Like 0Dislike

Share:

Table of contents:

Trucks KAMAZ began in 1969. For the new generation of trucks engineers have created a 4-stroke eight-cylinder diesel engine KAMAZ-740 V8. This powerplant had a displacement in 10852 cm3, and power it up to 210 horsepower. Then power had to expand from 180 HP to 360. These trucks were equipped with pneumatic clutch, 5-speed manual transmission with synchronizers.

Device diesel unit

The Design of these motors, when compared with other operating on diesel fuel has some advantages. The unit has relatively small dimensions, and also has less mass in comparison with the same YAMZ 238.the engine KAMAZ 740

Torque from the motor to the main nodes is transmitted through spur gears. Thus, the gears are drive system valve timing, pumps and compressors, and power steering.

This engine (KAMAZ 740) has a good start even at very low ambient temperatures. This became possible thanks to the power of the battery, starter and heater units before launch.

Engine specifications

Model of the power plant has received the name – diesel KAMAZ 740. The cylinders are arranged in V-shape. The crankshaft rotates in the right direction. The cylinders have a size of 120 mm, depth 120 mm. KAMAZ 740 Engine with a displacement of 10.85 L. has a high compression ratio of 17. Power on the passport in kW ranges from 154 to 210. Maximum torque of 650 kg/m Minimum fuel consumption is 165 litres, and the maximum is 178 liters each cylinder has one intake valve and one exhaust.KAMAZ engine 740 device

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Consider the engine KAMAZ 740, the various device components and systems.

Block

This site is nothing like the detail of the housing unit. It is intended for installation and fastening of all mechanisms and basic systems. The cylinder block is made in the form of monolithic molded construction. Item has holes and channels for lubrication and cooling.

At the top of this block are located under the Jack sleeve. Also, the housing includes channels and cavities for the passage of coolant. The lower part of the cylinder also serves as a crankcase. Here is a crankshaft. Carter has two technological holes for lubrication. Inside a node has a partition with special ribs. In these partitions and the walls of the crankcase made of a special bore, which closed lids. These details serve as supports for the crankshaft.

The Unit is equipped with supports for the camshaft are also placed here the tappets camshaft.KAMAZ engine 740 repair

The Casings serve as guides for the pistons. Together with the head unit, they form a special cavity, which is the combustion of fuel. The casings are made of special cast iron and are hardened by electricity.

The Upper part of the plane represented by the cylinder heads. Each with its own head. These parts are made of aluminum. Inside each head has a coolant jacket, which in turn is connected to the jacket unit. Also each head has oil holes, valves for intake and exhaust, a special slot under the injector.

Design and operation of lubricating systems

The Engine KAMAZ 740 is equipped with a lubrication system of the combined type. Depending on where you placed the conditions in which the working friction parts, oil is supplied in a variety of ways. The system can be sprayed, feeding oil at low pressure, either let it gravity.

The Device that delivers oil under pressure to the parts more prone to wear and work in especially loaded nodes. This node consists of fundamental devices and devices containing the grease filtering devices and supply and oil cooling.

The Oil passes from the sump to musopriani passes through a special filter in the form of a grid. It then goes to the oil pump. From the Plenum through a special channel, lubricant is supplied to the oil filter, and then on the highway. Further, in the lubricating channels under pressure passes the lubrication of cylinder head and cylinder block, and then to other nodes, such as crankshaft, gas distribution mechanism, the compressor and the fuel pump.KAMAZ engine 740 price

In the cylinders of excess lubricant is removed with the help of oil ring and then goes through the piston groove on. The so lubricated bearing of a piston finger in the top head.

From the main line oil is fed to the thermal and force sensor. If you open a faucet, which includes a hydraulic clutch, then processed and clutch. If it is in the closed position, the filters centrifugal cleaning liquid is fed to the pan.

If lubrication is not enough, falling output, as well as parts suffer excessive wear, the motor overheated, melted the bearings, and the pistons may jam.

The power supply System of the engine KAMAZ 740

At this point our review does not end there. We examined the engine KAMAZ 740, the device and lubrication system. Now consider the scheme of power.

The Nodes are in orderto keep the fuel clean, and then spraying it into the combustion chamber in accordance with the mode of operation of the power unit.

The Engine KAMAZ-740 are equipped with a feeding unit of the separation type. Here, the divided fuel injection pump and injectors. The system consists of tanks for storage of diesel fuel, fuel filters, low pressure pump, injection pump and fuel pipes.

How it works?

From the fuel tanks via a pump for pumping the fuel takes place on the filters. Then network toplivoprovodov low pressure diesel fuel is supplied to the injection pump. After the fuel pump pumps diesel high pressure portions based on the operating conditions of the engine through the injectors into the cylinders and combustion chamber. The injector in turn, atomize the mixture. Extra diesel oil falls again into the tank by a bypass valve.

Cooling System of the engine KAMAZ 740

Cooling is presented in the form of a closed system with liquid cooling and forced circulation.

In principle, the scheme of this system is no different from the usual for all car brands. If there is a diagram of the engine KAMAZ 740, and there you can see greater detail.cooling system of the engine KAMAZ 740

The coolant circulates by centrifugal pump. First antifreeze into the cavity of the left row of cylinders, then through the tube – in the right cavity. Then the mixture washes the cylinder liners and then through the holes – the cavity of the cylinder head.

Hot On the cooler goes to the thermostat then either the radiator or the water pump. Temperatures are regulated by thermostats and hydraulic couplings.

Main engine

Among the owners of this car the main fault of the engines KAMAZ 740 is the sharp decrease and power surges, increased consumption of lubricants and fuel. Also a popular fault is to a high exhaust smoke. Not uncommon and the pressure drop in the lubrication system.diagram of the engine KAMAZ 740

The Unit can work is unstable on idle, sometimes to experience various extraneous sounds in different nodes. Mainly faults connected with the crankshaft. Possible leakage of coolant.the power supply system of the engine KAMAZ 740

If the unit has been used to the limit, and most - if not had proper maintenance, the engine KAMAZ 740, repair is inevitable. But after overhaul the machine can work again in full force, and perhaps even much better.

Pricing

Today, this unit can still be purchased. Engine KAMAZ 740, the price will be, depending on the configuration and capacity from 550 000 rubles for a model with a capacity of 240 HP up to 600 000 rubles for a model with a capacity of 320 HP of Course, and can be purchased much cheaper. Market motors with a run at the moment offers a lot of options at lower prices.

So, we found all the features of the KAMAZ engine.


Article in other languages:

AR: https://tostpost.com/ar/cars/20097-740.html

BE: https://tostpost.com/be/a-tamab-l/37782-ruhav-k-kamaz-740-prylada-ramont.html

DE: https://tostpost.com/de/autos/37413-motor-kamaz-740-die-einrichtung-und-die-reparatur.html

ES: https://tostpost.com/es/coches/37181-el-motor-de-kamaz-740-dispositivo-y-la-reparaci-n.html

HI: https://tostpost.com/hi/cars/21790-kamaz-740.html

JA: https://tostpost.com/ja/cars/19733-kamaz740.html

KK: https://tostpost.com/kk/avtomobil-der/38156-oz-alt-ysh-kamaz-740-ryl-ysy-zh-ne-zh-ndeu.html

PL: https://tostpost.com/pl/samochody/39661-silnik-kamaz-740-urz-dzenia-i-naprawy.html

PT: https://tostpost.com/pt/carros/39322-o-motor-kamaz-740-dispositivo-e-repara-o-de.html

TR: https://tostpost.com/tr/arabalar/34643-motor-kamaz-740-cihaz-ve-onar-m.html

UK: https://tostpost.com/uk/avtomob-l/38555-dvigun-kamaz-740-pristr-y-remont.html

ZH: https://tostpost.com/zh/cars/29645-740.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

The ZIL-117 is the ever - living car

The ZIL-117 is the ever - living car

the ZIL-117 is the pride of the USSR, a car with a rich history. Five-seater rear-wheel drive "iron horse" of high class. At its creation took more than one year. Sedan was released in Moscow at the plant named after I. Likhachev ...

"Fiat 500X": specifications

In early 2012, the Italian designers first introduced the conceptual version of the model called "Fiat 500X”. Specifications and external appearance of this small crossover is already interested many potential buyers. A...

The Nissan NV200 is a practical minivan for a large family

The Nissan NV200 is a practical minivan for a large family

Nissan NV200 – is a versatile minivan, which was presented in 2009. Originally, this title was planned to produce a machine that could perform passenger and cargo transportation. However, it turned out somewhat differently.M...

How to store tires without wheels in the winter or summer? Proper storage of automobile tires without discs

How to store tires without wheels in the winter or summer? Proper storage of automobile tires without discs

Twice a year the cars “shoes” and before their owners the question arises: “How to store tires?” Tires do not like sunlight, ultraviolet radiation, moisture and extreme temperatures. In addition, they are s...

Motorcycle

Motorcycle "IZH Jupiter-4": technical specifications, pictures and reviews

Probably, the brainchild of Soviet auto and monopropylene'll be a long time to travel the roads of modern CIS. It would be on a motorcycle "IZH Jupiter-4".Historythe Road motorcycle "IZH Jupiter-4" produced machine-building factor...