Not spinning the starter. What to do?

If the car is not spinning the starter, the causes can be several. The car wound up with the pusher light – it means the fault is in the starter, or not of power supply from the battery.

In the first place, if not spinning the starter, check the battery. Contacts should be tight and not oxidized. If, turning the ignition, hear the click (the pull is triggered), so wire is in order and power is supplied, and the battery needs to be charged. Also tips will be the lights that begin to dim when the ignition is on. Here to fix the problem just – to install the new one or recharge the old battery.

With the rapid oxidation of the terminal after Stripping lubricate them. Supply voltage also depends on the quality of the installed terminals. It is better to put spare parts from brass or lead, because now began to push for such, made of a strange metal. They look fine, but over time the inside to form a film which is not conductive and is hardly visible.

In the absence of a click, if not spinning the starter, try checking the battery health with a known good car. And if she did, then you should look into the wiring and check its integrity.

The Above cases are simple. Now consider the situation more complicated. Why not spinning the starter and what could be the reason?

If the battery is in perfect condition and your car will be hard to not start, in this case, it is necessary to check the retractor relay in the coin. For this you need to remove it from the starter, disassemble and clean up with a file. And with reluctance to mess with the retractor, it is better to buy new. In the case of excellent work and this relay, you should pay attention to the alternator brushes. Indirect cause of fault could be wear, because suddenly they are not broken, and gradually erased.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

If the starter belching smoke, then in all likelihood shorted and replace it with a new can not be avoided.

Sometimes there is an open ground wire that connects the vehicle with the power unit, and therefore does not start the car, turns the starter, but in this case there is a click, however, heats the cable brake, clutch or gas. This may be due to the fact that after the next repair it is simply not put in place.

What to do when not spinning the starter (WHA)?

There are two types of starters for our domestic car. They are virtually identical and interchangeable. One end of the collector type and the second – an ordinary cylindrical.

Immediately give a definite answer, what could be the reason, it is impossible. Assume that the battery has a good contact in the terminals. Possible, of course, is to see the picture diagram of the electrical connections below before you start “cast” on failure, at least roughly imagine how it works at all. And you should not be embarrassed in case you have a car VAZ 2107, or any other model – everywhere all is almost identical, if not to take into account small details.

To already above, you can add that if a wire and he fell through the terminals of the starter, it is a little bare. To pull him from the terminal housing should not be, because to put in place is almost impossible, we have to remove the starter. So, the most basic probe – a small bulb with a couple wires, you can check the voltage on this exposed section of the wire, of course, with the running of the starter.

If there is no voltage, the possible fault may be the ignition key. Here is a bare wire to bring the voltage directly from the positive terminal. And in case of success, you just need to change the key. This is the simplest elementary and eliminate the fault.