Adjustment of PTO MTZ-80 with his own hands

Date:

2018-03-21 05:32:13

Views:

859

Rating:

1Like 0Dislike

Share:

Table of contents:

Adjusting the PTO shaft MTZ-80 is not only performed in specialized workshops, but also with their hands. This is a much cheaper process, especially if you have the suitable skills and to understand the peculiarities of technical equipment of the node. Consider the features of this procedure.

MTZ 80 PTO adjustment

First step

Adjusting MTZ-80 is performed in the following sequence (here these numbers correspond to the numbers indicated in the drawing).

Milestones:

  • The eccentric axle is in its original position so that the flatted “In” located in a vertical position on the right side. It must be locked by the stopper 17 and the bolt 16.
  • Next, disconnect the rod 4.
  • Twist the bolt 9, while freeing up the spring 6. For security purposes when turning the bolt 9 ensure that the glass 7 is constantly in contact with the seat until the unclamping spring.
  • Remove the hatch cover on the rear axle, getting access to the screws 13.
  • Secure the lever 11 in the neutral position with bolt M10*60 or stem 10, a diameter of 8 mm. put the socket on the lever and a corresponding hole on the rear housing.

adjusting the PTO MTZ-80

Further adjustment of PTO MTZ-80

Next, the operation is as follows:

  • Removed the retaining plate 26, screwed the screws 21 with a force of 10 kgf, after which each element is unscrewed a couple of turns.
  • Stud bolt 10 is removed, freeing the lever 11 to the original position for the correction.
  • Bolt 9 to spin through his bow into the recessed part of the glass 7 to the size “And” 26mm.
  • Translate the arm 11 in position “On”.
  • The Rod 4 is adjusted by the adjustment with the analogue 15 until the overlap zone of the swing arm 1 in the middle part of the slot of control panel.
  • Upon completion of work put in place of the stopper 26, the hatch, thrust zakontraktovat 4 and 15 together with the bolt 9.

The chart shows other items:

Recommended

"IZH 350 Planeta Sport" – frisky Soviet bike

It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

adjusting the PTO MTZ-80 with his own hands

Features

Additionally, when adjusting the PTO MTZ-80 with his own hands may be necessary to adjust the belt brakes. If:

  • There is a slipping PTO.
  • When switching the control lever 1 rests in the front or rear portion of the slot in the control panel.
  • The force on the element 1 exceeds 15 kgs.
  • Have a fuzzy fixation lever 1 into the extreme position or when turned on and off.

Setting the belt brakes

This operation adjustment PTO MTZ-80 is performed by the method of external adjustment, namely:

  1. Set the lever 11 in neutral position, fix it in position by inserting a pin 10 in the holes provided.
  2. Twisting the Bolt 16, the plate 17 is dismantled slotted tail section on the axis 15.
  3. Special key to turn the eccentric 15 in a clockwise direction to a suitable gap between the brake band and drum work (check the position manually if the shank does not rotate-it means that the desired position).
  4. Plate and bolt installed.
  5. From the lever retracts the latches.
  6. Adjustment of strips PTO MTZ-80 can be considered completed.

adjusting the ribbons of PTO MTZ-80

What to look for?

After the external adjustment a few times the axis 15 can take the extreme left position. This indicates that the residual supply external adjustments. To normalize the situation and turn the Cam counterclockwise to its original position. Then make adjustments PTO MTZ-80 in the manner specified above.

If all manipulations are done correctly, the lever 1 in the position "On.” and “Off” should not reach the edge of the panel is less than 30 millimeters, while the transition is in the neutral position should be clear.

In some versions of the tractors adjusting the PTO MTZ-80 is no mechanism of external adjustments in his absence. This particular operation is performed the same way as described above, after repair or Assembly at the factory. On models with a compact cabin the index of the “B” is 50-60 mm.

The braking system and the lack of slip depends solely on the spring fixture. This is especially true of the availability of working areas and aggregating them leverage. Slip the PTO suggests that springs or levers meet additional resistance when they are moving without sufficient lubrication in the mechanisms.

Adjusting the PTO shaft MTZ-80 with your hands

During the operation, carefully observe the changing position of the lever the PTO shaft, not allowing the stop element to the floor of the cabin, otherwise there may be delays in emergency mode. Additional symptoms of the need for adjustments is considered to be the increased course of the control lever and increasing the pressure in the activation position "On.” and “Off”, and also Vice versa.

MTZ 80 shut off PTO gnashing of adjustment

Adjusting the PTO shaft MTZ-80 is performed in the following sequence:

  • Combine holes on the threaded bore of the body and the analogue on the lever, then it must be locked whenusing a hinge.
  • Remove the cover, to capacity tightening adjusting screws (force – 8-10 N/m), then loosen them 2-3 turns.
  • Control the ease of rotation of the served node by rotating the hand shank spline.
  • Connect the rod with the lever by using the finger of cylindrical form, well sprintout.
  • Establish glass in gathering with a spring in the recess of the tank, while there will be a slight rotation of the locking bolt. The force of compression spring with a glass – is not less than 200 kgs.
  • Made fixing the Assembly in a compressed state by means of a bolt which is screwed into the nut welded to the lid.
  • Turn Screw until free movement of the Cup spring mechanism relative to the lid.
  • Securely fix the bolt in the arm by lock nuts.
  • Adjusted the thrust so that the distance from the lever to the bottom edge of the cab was 50 millimeters in enabled mode.

Renovation

The Tractor MTZ-80 to adjust the PTO in any case is placed on to repair if there are cracks and dents on the strap, the glass or platen. Eliminate the problem as follows:

  • Combine the nest of a roller switch and the back of the bridge with the control lever. After matching the holes they are fixed by the mounting bolt.
  • The lock nut is loosened and the set screw is screwed into the lever of the switching roller to the limit.
  • Retaining bolt is screwed into the glass, then gently removed the adjusting counterpart.
  • After that dismantled the glass with springs, then it is dismantled and unusable parts changed.

adjusting the PTO the tractor of MTZ 80

Other problems

  1. Problems with Cam clutch. When this faulty dismantled cabin, from the rear axle detaches the node transmissions. Then you replace the element, because its repair has no meaning.
  2. When you shut off the PTO MTZ-80? Rattle – adjustment in this case is performed with simultaneous replacement of worn teeth of the Central gears or splines. To do this, first remove the PTO shaft by a wheel, and then evaluated the condition of the item. If there are failures in the form of increased gaps or razbaltyvaniya parts are sent for repair.
  3. What to do if the shank of the PTO shaft move freely? This indicates a weakening of the locking nuts. You must completely remove the node, and then restore the threads and tighten the nut until it stops. If that is not possible, carry out the disassembly of the entire structure with a labour-intensive repair.


Article in other languages:

AR: https://tostpost.com/ar/cars/8360-pto-mtz-80.html

BE: https://tostpost.com/be/a-tamab-l/14947-regulyavanne-vom-mtz-80-sva-m-rukam.html

DE: https://tostpost.com/de/autos/14951-einstellen-der-zapfwelle-mtz-80-mit-ihren-h-nden.html

ES: https://tostpost.com/es/coches/14960-ajuste-de-la-toma-de-fuerza-mtz-80-con-sus-manos.html

HI: https://tostpost.com/hi/cars/8362-pto-mtz-80.html

JA: https://tostpost.com/ja/cars/8361-pto-mtz-80.html

KK: https://tostpost.com/kk/avtomobil-der/14949-retteu-vom-mtz-80-z-olymen.html

PL: https://tostpost.com/pl/samochody/14945-regulacja-wom-w-mtz-80-w-asnymi-r-kami.html

PT: https://tostpost.com/pt/carros/14941-ajuste-o-pto-mte-80-com-suas-pr-prias-m-os.html

TR: https://tostpost.com/tr/arabalar/14952-ayar-pto-mtz-80-elleriyle.html

UK: https://tostpost.com/uk/avtomob-l/14951-regulyuvannya-vom-mtz-80-svo-mi-rukami.html

ZH: https://tostpost.com/zh/cars/9153-mtz-80.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Oil

Oil "Kiks 5W40": reviews and features

Today, for various car brands represented a huge amount of money for motors. They need to be able to choose the right. Depends on the durability and stability of the engine. One of the famous brands is "Kicks". Its lubri...

Car Ford Granada

Car Ford Granada

the First car Ford went on sale in 1972. Was presented in several body styles: four - and two-door sedan, four-door wagon and two-door Granada coupe with lots of chrome parts. Model with basic configuration before 1975 were called...

"Cadillac Escalade": car owners reviews, specifications and features

In 2013, the world was a model of the fourth generation of the Cadillac Escalade SUV. It was expected novelty, so that rapidly growing sales was predictable. Many people became owners of this car and some of them after some time a...

Alarm

Alarm "Tomahawk 9030". "Tomahawk 9030": instruction and feedback

For car owners the most urgent issue is the safety and protection of the vehicle. The most effective way of protecting your car is to install an alarm system. Car alarm "Tomahawk 9030" today is one of the most popular and in deman...

Scary universal Nissan Qashqai +2

Scary universal Nissan Qashqai +2

Nissan Qashqai +2 was a result of the peculiar attachment of two additional seats to the standard version of the model. The car first debuted to the public in 2007, and immediately gained popularity both in the domestic and Europe...

The development of the automotive industry. Vintage machine.

The development of the automotive industry. Vintage machine.

Cars flooded the planet. They observed a man crossing the oceans, transporteras trains. Each moment coming nearer to his owner who's already counting the money, simultaneously keeping an eye on the garage.You know that means a rep...