How to make a tattoo machine out of nothing?

Date:

2019-07-16 12:00:25

Views:

731

Rating:

1Like 0Dislike

Share:

Table of contents:

I Dream to become a famous tattoo maker, but don't know where to start and where to get the necessary equipment, which costs a fortune? Do not be sad about this, because there are quite affordable way to make a tattoo machine myself. This will be the device of the rotary type. To make it, you will need the following simple “parts”: the power supply with a variable voltage, the thin guitar string, a motor from old cassette recorder or player with a pair of wires, gear from the same small Bush, ordinary gel pen, a piece of plastic tube.

So, machine to tattoo their hands involves, first, the presence of the body. Actually, this is what you will hold in your hand when tamping tattoos. Its manufacturer to start out. To do this, take a pen, remove it from the rod (it is not emitted, it is needed) and the rear part cut it by about a third. In the nose of the handle, the side of you knife to make a small hole (about 5mm) to make it easier to collect the ink. Little with a file clean the edges of the holes to fine sawdust does not get into the wound.

Next step, how to make a tattoo machine, will be making a guide needle. It is made of a rod of the same handle. It also needs to be cut to the length of the hull and remove the paint. Then take out of the rod nose, take a needle and squeezing it inside the ball. This is to ensure that the string could move. If the spout is too narrow, it needs to expand, stacev the tip with a file: the string must not be stuck anywhere and for anything to cling to. Once all parts are ready, insert the tip of the rod to its rightful place, and the rod in the handle. The Cabinet is ready.

Recommended

The most effective methods of seed germination

The most effective methods of seed germination

Despite the fact that the method of seedling in vegetable production is a very time consuming process, it is used by most gardeners. Planting seeds in open ground is an easy and convenient method, but it is effective only in certain climatic zones. I...

Retro-reflective paint. The scope of

Retro-reflective paint. The scope of

When the vehicle began to fill the road, their popularity began to gain reflective paint. Thanks to this paint, as drivers and pedestrians becomes much easier to avoid accidents in the dark. Purpose paint Reflective paint – paint material, whic...

How to make icon with your own hands - options izgotovleniya (simple and complex)

How to make icon with your own hands - options izgotovleniya (simple and complex)

In Soviet times, many collecting badges, emblems, pennants. To get them was not easy. And today, thanks to technology, you can make them yourself. Knowing how to make icon with your own hands, and you can make original gifts to your friends, and make...

Continuing the theme, how to make a tattoo machine, now you're making needles out of guitar strings. Its length should be designed so that the tip, which will be engraved the tattoo, always, in any situation, sticking out of the handle. When the string is pulled back, i.e., into the body, its “needle” should be possible at 0.5-1 mm. In “front position” enough 1.5-2 mm. At the opposite end of the strings will need to do a loop. Therefore, to avoid mistakes in calculations, insert the string in the rod which, in turn, place the handle body. And that the string was smooth, not bent, not folded, it can be pre-stretched and well to be heated on the fire.

At this stage, leave everything as it is and proceed to the next step. How to make a tattoo machine? Next we need to attach the motor. To do this, take a piece of prepared plastic tubing (it will serve as a motor mount) and cut it lengthwise into two parts. Then take each half and cut from it a longitudinal piece of a few centimeters in length. Determine the length of the eye, because this cut area at the bend should cover the motor by about a third. Each clipped part, gently warming on the fire, bending, rounding out. These rounded halves insert the motor (wiring it needs to go outside). Formed below the motor the groove of the cut tube (untouched part) is inserted into the handle. All this beauty tightly wrapped with electrical tape or cinch clamps. Then put on the pin of the motor gear, which will serve as a crankshaft, moving the needle back and forth. It should sit very tight and not scroll. Next, take a bushing, it will wear a loop of string, which also needs to sit tight enough. In-mould plastic bushing in the sprocket closer to the center so that when scrolling the needle in any case was not part of the handle completely.

The Final stage of how to make a tattoo machine will be connecting the wires of the motor to the wiring of the power supply. Try to plug it in. Should work.


Article in other languages:

BE: https://tostpost.com/be/hatn-tul-nasc/30552-yak-zrab-c-tatu-mashynku-z-n-choga.html

DE: https://tostpost.com/de/gem-tlichkeit/30570-wie-machen-die-tattoo-maschine-aus-dem-nichts.html

ES: https://tostpost.com/es/la-comodidad-del-hogar/31114-c-mo-hacer-un-tatuaje-de-la-m-quina-de-la-nada.html

KK: https://tostpost.com/kk/domashniy-uyut/30517-alay-tatu-sady-eshte-e.html

PL: https://tostpost.com/pl/komfort-domu/30394-jak-zrobi-tatua-maszyny-z-niczego.html

PT: https://tostpost.com/pt/o-aconchego-do-lar/30418-como-fazer-tatuagem-m-quina-de-escrever-do-nada.html

TR: https://tostpost.com/tr/domashniy-uyut/32010-nas-l-d-vme-makinesi-bir-ey.html

UK: https://tostpost.com/uk/domashn-y-zatishok/30494-yak-zrobiti-tatu-mashinku-z-n-chogo.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

Finnish entrance doors for a country house. Photos and reviews

Finnish entrance doors for a country house. Photos and reviews

Finnish entrance doors Fenestra is able to create atmosphere, mood and style.the front door is the calling card of any home. This is an important element of the interior, which is outside of the home. Exterior doors made in the de...

Ceramic brick: the advantages and disadvantages of this material

Ceramic brick: the advantages and disadvantages of this material

For many decades, ceramic brick is considered to be one of the most popular building materials. After reading today's article, you will learn about the main advantages and disadvantages of similar products.What is this material?it...

Three-phase meter

Three-phase meter "mercury 230": reviews and connection diagram

the Meter "mercury-230" – this equipment which is designed to account for power and energy (reactive & active) in one/two directions in three-phase 3 - or 4-wire AC systems (50 Hz) by means of measuring transformers. It has ...

Rack ceiling in a bathroom - how to make the right choice?

Rack ceiling in a bathroom - how to make the right choice?

to begin to repair in your apartment, you should think in advance how to choose a ceiling. Particularly acute this issue is for the bathroom. Constant temperature changes and high humidity levels can adversely affect many types of...

Farm: types of farms, description, classification and working principle

Farm: types of farms, description, classification and working principle

the construction of the farm cover a different scope, addressing mechanical power and frame subassemblies. In essence, they represent the core of the system, which, depending on operating conditions may provide different degrees o...

The root system of the arborvitae: features, photos, dimensions

The root system of the arborvitae: features, photos, dimensions

Most gardeners when choosing evergreen conifers prefer to unpretentious and very beautiful tree - Thue. In appearance thuja has a similarity with its closest relatives: juniper and cypress. It is characterized by a pyramidal shape...