Liquid for rinsing "Laurel". Flushing "Laurus": reviews

Carbureted cars every year is getting smaller. Leading automakers have long switched to injection type of injection, which has many advantages. This lower fuel consumption, and improved productivity, a more balanced air-fuel mixture, etc. However, problems have also been added. Injector more costly to repair, in addition, are often clogged his injectors for cleaning which is often used means "Laurel". Flushing this has its pros and cons, we are with you in this article, we'll talk.

Why clog the injector of the car and how to fight it

Most of the chemical compounds contained in the fuel such as sulfur, olefin and benzene to form tar deposits in the fuel system of the vehicle. They are not removed with gasoline, as covered with a dense crust brown. Than lower quality fuel is used, the more these sediments over time accumulates in the car.

It is logical that the efficiency of the car is reduced as a whole, like dirty injectors. Due to the fact that the complex perfume - the procedure is quite labor intensive, so many go until the critical moment. Car will start troit, the engine will run uneven, and some morning you can not even start. To avoid this, use a liquid called "Laurel". E liquid in this case comes down to a few simple manipulations, which we'll discuss in this article. You also need to address the cooling system of the engine.

Recommended

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

Active additives - good or bad?

There are a large number of supporters of chemically active components, and those who use them flatly refuses. Both the first and the second are based on life experience, technical expertise or simply expert advice.

First we need to understand what effect the flushing of the system of the car. Highlight the main strengths and weaknesses:

• Chemically active components that can be called aggressive, have a negative impact on all the rubber gaskets and seals. This leads to their accelerated wear;
• If the viscosity of the additive does not correspond to the viscosity of the oil, its use is strictly forbidden, as indicated by the manufacturer with flushing;
• Substandard tools to remove oil deposits make it worse (clog up the catalyst, the spark), causing them more problems than good.

That is why not every motorist is happy with the result.

Why it is better not to experiment

Many are trying to put various experiments with leaching, which in most cases end sadly. For example, alter the concentration of the washing. You do not need because you will loose almost the whole point of using. Due result it gives, and the money spent.

In Addition, do not fill more than necessary, especially if the tank is low on gas. This can lead to that you simply do not get to a gas station without incident. For example, soft washing "Laurel" if the concentration has an extremely negative impact on the rubber seals that may later lead to the replacement of gaskets and seals, and it is expensive.

Means "Laurel": the rinse injector and engine

If you have your car noticed jerking while driving, unstable engine operation, the problems with running in the cold season, it's time to use detergent additives.

All work quite simple to do yourself. For this in the gas tank every 5-6 thousand kilometers is filled with a special tool. However, such an event occurs, rather, as a prevention, rather than treatment. However, it should be done regularly even to owners of new cars. As for the "monastery", it is used somewhat differently.

The Sequence of actions when flushing

First we need a "Laurel" soft washing of the engine. It is also desirable to have a few liters of gasoline and a spout for pouring. In the proportions specified on the jar, mix Laurel and gasoline, and then find the tube that goes from the vacuum pump to the intake manifold, disconnect it and injected out the mixture.

It is Necessary to start the engine and keep the rpm within 2500. Thus constantly add a liquid in a tube. At this time, the engine operation will be unstable, but that's okay. From the exhaust pipe can exit the sludge and a large amount of smoke. The exhaust at this time will be extremely toxic, so it is better not to breathe. Kill the motor and allow it to cool, after which it is advisable to replace the spark plug with a new one if it is not the first freshness. If the plugs are brand new, at the time of washing, it is better to put the old, as likely they can be coking.

About the producers of cleaning

One of the most popular liquids that has the highest number of positive reviews - Laurel. This manufacturer has established itself from the best side. This fluid must not be poured into the tank, which is listed onlabel. According to owner reviews, the average rating of the fluid is 4 points out of five. Many say that miracle is not worth waiting, but with their immediate task tool manages as needed.

Another popular manufacturer of washing - "Winx". The cost is roughly the same as "Laurel" (a bit more expensive, but not essential). As for the ratings, then there is also 4/5. However, experts note that the Laurel does not worse, "Winks" but health less harmful. A tool such as "high-gear", expensive, but cleans a bit better. And now let us return to our subject.

The composition of the additive flushing

To understand the bad for a car to use this kind of cleaning or not, you need to deal with components that wash out the engine and injectors from carbon deposits. The main component is kerosene. It is a great way to clean dirt and oil. For greater efficiency added chemically active detergents, which make it possible to remove the oil deposits on the injector channels.

About car cooling system

When the antifreeze becomes abnormal color, usually bright orange, it indicates the presence of rust. In this case, you must flush the radiator and all channels. This can be done both independently and in a HUNDRED. As the primary means by "Laurel". Flushing the cooling system will take a lot of time, as one approach in case of strong pollution to improve the situation will fail.

The First step is to drain the system of old antifreeze. Then take Laurel and fill one jar, then to low, add distilled water. Start the engine and let it run for about half an hour. After that drain and see that in the pipes and radiators a lot of rust. The procedure should be repeated again in the same order. If the rust is still allocated, then in the third stage we use just the distillate, without rinsing. After the above procedures, fill with fresh antifreeze and enjoy the result.

Regular success

We have already started to grasp what functions are performed by Laurel. Flushing the cooling system, injectors and engine - all under the power of this tool. But do not forget that for maximum results, it is necessary to conduct regular maintenance.

For example, after cleaning injectors they are dirty again, no matter how it was sad. As a result, the situation repeats. To avoid this, you need to use a detergent, but not too often. When you replace the antifreeze, which is performed once in 12 to 24 months, preferably for prophylaxis to clean the system. Similarly, when changing the spark plugs on a new to clean injectors and fuel system in General. It is superfluous will not be exact, but you will be able to sleep peacefully.

Laurel: flushing of the cooling system. Consumer reviews

The Most reliable way to verify the quality of a means - test for yourself. However, this approach often leads to tragic consequences. For this reason, before using the washing have to watch what they write about it motorists or a HUNDRED.

As for the "Lavra", today it is one of the most popular means of Russia along with the "high-gear" and "Winx". Rinsing, according to the reviews, has excellent detergent properties and at the same time not too aggressive to the rubber seals, though, and has a negative effect.

Pollution Degree injectors

As practice shows, not every car owner timely services your car. This usually leads to more serious consequences. As an example, it is necessary to bring the nozzle. They are responsible for uniform injection of the fuel-air mixture into the cylinder. Over time, as the cylinder and injector enveloped with soot, causing falling efficiency of the motor. Experts distinguish three degrees of contamination of nozzles:

• 5-7% - almost imperceptibly for the driver, as there are no symptoms. Slightly increases fuel consumption.
• 10-15% - noticeable jerking during movement, the decline of dynamic performance, increasing fuel consumption.
• 15-30% - a critical level. Significantly increases the gasoline consumption, at idle the engine troit, cold often stalls.

Based on the above, we can conclude that the first stage is not so critical, moreover, to detect the fault can only be experienced specialist. But the lack of action on the part of the driver lead to the second, and accordingly, the final stage. The situation here is more serious and requires special attention.

Security system after cleaning

About the quality of domestic fuel, and can not speak. Often the fuel contains large quantity of impurities, exceeding the various standards and environmental tolerances. In some cases, the gasoline is diluted, that the detrimental effect on the fuel system of a modern car. If we add to all this the difficult working conditions of the internal combustion engine (tubes, continuous operation, overheating), and to failure near. Well if you use the engine flushing "Laurel" reviews, which confirm its effectiveness. But hardly anyone uses such a toolregularly.

To "iron horse" worked fine, it is desirable to protect the system special fluids directly after washing. If you adhere to the advice of experienced professionals and manufacturer's cars, then you can significantly extend the life of critical machine components. This applies to the cooling, fuel, brake, etc.

To Summarize

Here we understood how is done and what is needed to flush the injectors. "Laurel" reviews, which all boil down to the fact that the tool is worthy of attention, accomplishes the task completely. But we should not forget that the abuse of such a reactive liquid can lead to "eat" the rubber seals and gaskets. For this simple reason, you need to follow the instructions and not invent anything superfluous.

Really high-quality washing Lavr - reviews repeatedly confirm this. Domestic manufacturer produces a vehicle is not at the lowest cost, but in recent time, the efficiency it higher than the "Winx". Also, the experts prefer to work with "Laurus", which is not surprising, given the harm to health caused by "Wincom".

The operation of the injector will be unproblematic if the system is periodically monitored and cleaned it, and also use the liquid to wash "Laurel". Again please note that to fill the tank "Laurel" not if it is written on the label! In the absence of any experience flushing of the injector and cooling system, to provide better opportunity to engage these professionals. But here we need to be confident in the service station, as there are cases when the money from the driver took, and their work did not, and if they did it poorly. So always be vigilant.