The device and principle of work of automatic transmission car

Date:

2020-02-17 22:20:27

Views:

521

Rating:

1Like 0Dislike

Share:

Table of contents:

Today, cars are being Packed with different types of CAT. And if earlier the most part of it were the mechanics, now more and more drivers prefer automatic. This is not surprising because such transmission is easier to operate, especially when it comes to travel in the city. Until recently, such boxes had lower efficiency. The old torque Converter was slowly changed gear and the car was much more fuel. But today, the design of the device and principle of operation of the automatic transmission are slightly different. These boxes are ways to switch quickly and with them, the car uses less fuel. But about all under the order.

Types

At the moment there are several varieties of automatic boxes. This is the classic automatic with torque Converter, CVT and DSG robot. The latter was developed specially by the concern «Volkswagen, Audi”. The device and principle of work of automatic transmission of these types is significantly different. But what unites them is the gear shifting in automatic mode. Consider in detail the features of each of these transmissions.

General machine

It is a hydromechanical transmission. Despite the fact that the design appeared more than half a century ago, it is still very relevant. Of course, the device has been significantly modified to the present day. Now these boxes have six gears. If we talk about cars from the 80s and 90s, they had a four-speed automatic transmission.

principle of operation of the hydraulic system of the automatic transmission

The design of this transmission includes:

  • Automatic transmission.
  • The torque Converter or “donut”.
  • Control System.

If such transmission is completed with front-wheel drive car, the composition also includes a main gear and differential. One of the main parts in the device of automatic box – it is the torque Converter. It consists of several parts. This pump, a turbine and a reactor wheel. Thanks to them is a smooth transfer of torque from the engine to a manual transmission.

Recommended

How does the rear bushing front arm and how many it serves?

How does the rear bushing front arm and how many it serves?

The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...

Oil consumption in the engine. Six reasons

Oil consumption in the engine. Six reasons

It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...

How does the exhaust system?

How does the exhaust system?

The exhaust System is designed to remove combustion products from the engine and output them to the environment. It also must be ensured a reduction in noise pollution to acceptable limits. Like any other complex devices, this system consists of seve...

In the automatic transmission device includes a clutch (freewheel and lockup). These elements together with turbine wheels are closed in a round metal case that is shaped like a bagel. Inside the torque Converter has a working ATF fluid. With the crankshaft is connected to the impeller. And from the transmission is the turbine. Between these two elements is also placed in the reactor wheel.

How it works?

What is the principle of automatic transmission of this type? Classic machine works in a closed cycle. As we said earlier, there is a good ATF fluid. This kind of transmission oil. But, unlike the manual transmission, it not only performs a lubricating function, but also transmits torque. What is the fluid coupling of automatic transmission working principle? Under the pressure of the fluid supplied to the turbine wheel (from the pump), and then fed to the reactor. Since it has the blades of the special shape, the flow rate of the fluid during the rotation of the element begins to gradually increase. Thus, ATF-oil drives the turbine wheel.

Peak torque in the transmission is formed when starting the car. The growth speed of the machine, included in the lockup clutch. The latter serves to lock tight "donut" automatic transmission at certain engine operating conditions. This usually happens when the speed of rotation of the shafts coincide. So, the torque is transmitted to the box directly, without “grindings” and changes gear ratios. By the way, modern automatic transmissions used the slip clutch. She is able to exclude the full lock the torque Converter in certain modes. This contributes to the smooth set of speed and fuel economy.

Automatic transmission in automatic transmission

As such mechanics, familiar to all motorists, in this transmission there. The role box performs a mechanical planetary gear. It can be designed for different number of stages – from four to eight. But still the most common – a six-speed automatic transmission. In rare cases, you can meet nine-automatic (for example, “Ranged Rover Mog”).

How does an automatic transmission? This node is in the transmission is a set of consecutive speeds. They are all United in the planetary gear set. The planetary gearbox includes the following components:

  • Solar and crown gear.
  • Led.
  • The Satellites.
automatic transmission Toyota

If to dwell on the device and principle of operation of torque Converter automatic transmission, you will notice that the change in torque is done by means of the carrier and crown and sun gear. When locking of the second mechanism increases the gear ratio. The locking itself is done by operation of friction clutches. They hold components of the planetary gear by connecting them with the body of the box. Depending on the brand of car, the design uses a multi-plate or band of the friction brake. Both types of systems are controlled by means of hydraulic cylinders. A signal to the clutch is supplied from the distribution module. And to exclude the rotation of the carrierthe opposite direction, in the device of the automatic transmission has an overrunning clutch.

Management System

It is impossible to imagine an automatic transmission, the principle of which would not depend on electronics. So, in this system includes various sensors, control module and control unit. During the transmission, the system reads the information from various elements. This temperature sensor ATF-fluid, the frequency of shaft rotation for output and input, and accelerator position. All these signals are processed in real-time. Then, the control unit generates control pulses that go to the actuators. Also note that the principle of the hydraulic automatic transmission is based not only on reading data from sensors, but also on aligning the signals that are available in the electronic engine control unit.

For flow control of working fluid and the action of the slip clutch responds to the distribution module that consists of:

  • Solenoid valve (they have a mechanical drive).
  • Spool valves.
  • Aluminum body in which are enclosed the above items.

Considering the principle of operation of automatic transmission «Toyota», it is important to note such a thing as solenoids. These items are also called solenoid valves. Why the need for the solenoids? Thanks to these elements regulates the pressure of ATF fluid in the box. Where is produced by oil pressure? This task is performed by a special gear pump, automatic transmission. The working principle of it is simple. This element of the hub of the “donut”. Rotate with a certain frequency, it captures impellers a certain amount of oil and pump it. And so the working fluid does not overheat and the principle of operation of the automatic transmission of the vehicle is not compromised in the design of some boxes is the radiator. It can be brought out separately in the front (hidden under the bumper) or to connect to the radiator for cooling. The latter scheme is often practiced in cars «Mercedes».

The Selector

The Principle of operation of the selector of the automatic transmission is extremely simple. This mechanism is structurally coupled with the spool that performs a specific operation mode automatic transmission. Just there are several:

  • Parking.
  • Reverse.
  • Neutral.
  • Drive.
torque Converter transmission

But that's not all. If we consider the principle of operation of automatic transmission ‘Honda’, you will notice that the selector has a sport mode. To enable it, just move the lever to the appropriate position. Considering the principle of operation of automatic transmission “Nissan”, is to say that on some models has a manual shift transmission.

Robot DSG

This type of transmission is relatively recent. The first models were applied only in mid-2000. Initially, these boxes were installed on the car «Skoda». But they can also be found on the «Volkswagen» and “Audi”.

Among the features worth noting a completely different working principle of automatic transmission. The torque Converter itself is absent in principle. Instead, he uses twin-disc clutch and dual-mass flywheel. This design allows to significantly reduce the time interval between the switching speeds.

If to speak about the device in the design of this box include:

  • Manual transmission with two rows of gear.
  • Electronic control.
  • Differential.
  • Main gear.
  • Double clutch.
operation

All the above elements are enclosed in a single metal housing. Why the design is the dual clutch and two sets of gear? If we consider the principle of operation of automatic transmission car with DSG, it should be noted that while one transmission is in operation, the second is already preparing for subsequent inclusion. It happens during acceleration and at low speeds. Present in such transmission and the clutch. They are connected through the main hub with its rows of gears in the transmission.

There are several types of DSG boxes:

  • Six.
  • Seven-speed.

The Principle of operation of the automatic transmission of the first type is based on the action of ‘wet’ clutch. So, in the box there is a special oil that provides not only lubrication, but also cooling of the friction. Fluid under pressure circulates in the system and is transmitting torque.

As for the second type of DSG, here already applied dry clutch. The principle of operation is similar to manual transmission – the disc is pressed against the flywheel by means of friction transmits the torque. According to experts, this scheme design is less reliable. The resource disk is about 50 thousand kilometers, and the replacement cost reaches $ 700 along with supplies.

A Series of gears include a reverse speed, and odd and even speed. Each row represents a set (consisting of primary and secondary), and a different set of gears. To implement reverse, the design uses an intermediate shaft with a reverse gear.

As in the classic slot machine, there are electronics, which controls the gear shifting. This includes the control unit, sensors, and actuators. So, first, the sensors read the data about the frequency of rotation of the shafts and the position of the forkgear, and then the unit analyzes this information and uses a specific control algorithm.

The Hydraulic circuit of DSG consists of:

  • Spool valves that operate the selector.
  • Solenoid valves (the same solenoids). They serve to shift gears in automatic mode.
  • Valves pressure regulation, that contribute to the harmonious working of a friction clutch.

How does the DSG?

The Principle of operation of the hydraulic system automatic robot is the sequential switching of several programs. When the machine begins to move, the system includes a first speed. The second is already engaged. Once the car gained more speed (about 20 kph), the electronics switches the speed increased. The gear is third gear. This happens until the most high. If the car reduces speed electronics introduces engaged already in a lower gear. Switching is done instantly, because the design involved two sets of gear.

Usage

It is Worth noting that such transmission is not applied on each car. As we said earlier, the majority – of the machine of the concern of “CAR”. But commercial vehicles (for example, “Volkswagen Crafter”) they are not staffed. And all because the box is designed for a certain threshold torque. It should not exceed 350 Nm.

the working principle of automatic transmission Toyota

This applies to six-speed transmissions. DSG of seven speeds and does not withstand more than 250 Nm. Therefore, to meet such a box can be a maximum on “the Touareg” and weaker cars like "Passat" or "Octavia".

CVT

This gearbox also works in automatic mode. It appeared half a century ago, but became actively used only in the last 10-15 years. What is a CVT? This is a continuously variable automatic transmission, which smoothly changes the gear ratio through a belt or chain transmission. Changing gear ratios is as of the set speed of the vehicle. At the moment, this box is widely used in the following brands:

  • “Nissan”.
  • «Mercedes».
  • ‘Honda’.
  • “Audi”.
  • "Subaru".
  • «Toyota».
  • «Ford».

What the pros have with this box? Due to the smooth change of gear, the car picks up speed rapidly and without jerks. The driver and passengers do not feel the jolts when accelerating, no matter how hard I pressed the accelerator pedal. However, there are pitfalls. This box also has limitations in the torque and DSG. Therefore, it is mainly used on the cars.

Types of CVT

There are several types of data transmissions:

  • The Toroid.
  • V-Belt CVT.
torque Converter automatic transmission operation

Both types of transmissions have almost the same structure and principle of work. In the design of CVT included:

  • Control System.
  • A Pulley that transmits torque.
  • A Chain or belt drive.
  • The Mechanism of separation box (used for reverse gear).

To the drivetrain of the perceived torque, the design involved clutch. It can be of several types:

  • Centrifugal automatic.
  • Electronic.
  • Multi.

There are variable speed, where the clutch applies the torque Converter (like classical automata). Typically, such a scheme is practiced in cartons “MULTIMATIC” from “Honda». Experts believe that this type of grip and most reliable resource.

Drive

As we have said, the CVT can be used in different drive – chain, or belt drive. The latter is more popular. The belt comes on two pulleys, which form the conical disks. These pulleys are able to move and spread out depending on the need. For convergence drives the design includes a special spring. The pulleys themselves have a small angle of inclination. Its value is approximately 20 degrees. This is done in order that the belts can be moved with minimal resistance while working the box.

Now, about the chain drive. Circuit for automatic variable gear box is a few metal plates that are connected by axles. As experts say, such a system design is more flexible. The chain is able to bend at angles up to 25 degrees without any loss of the resource. But unlike belt-drive, this drive has a different working principle. The automatic transmission transmits torque at a point contact with the pulleys. In certain areas there is a high voltage (the friction force). This achieves high efficiency. And that the pulleys were not worn out from the stress, they are made of high-strength bearing steel.

Reverse gear in the variator

Since the drive of the variator is able to rotate in one direction only, to implement a reverse gear engineers had to develop a separate planetary gear. It works and works similar to the gearbox in a classic slot machine.

Management System

Similar to the previous automatic transmission, the variator is usedthe electronic control system. However, its principle of operation is somewhat different. Thus, the system adjusts the diameter of the disks of the variator.

automatic transmission operation

As you change the speed, one pulley diameter is increased, and the second – is reduced. Modes can be changed using the selector by sensor automatic transmission. The principle of operation of CVT with a chain drive and belt drive is to change the diameter of the pulleys.

The problem

Due to the complicated design and the low prevalence, many services refuse to work with such transmissions. So the variators bad got accustomed in our country. As shown by operating experience, a resource box even with proper maintenance is no more than 150 thousand kilometers. In view of this, it is wise to buy such a car just in new condition that are out of warranty. To take a car on the variator with hands is dangerous – you can get to the costly repairs that will take far not each service.

Summing up

So, we found the device and principle of operation of the hydromechanical automatic transmission, robotic and variator. As you can see, all these boxes are arranged differently and have their own algorithm of action. What kind of transmission is better to choose? Experts say that the most reasonable choice of classic slot machines. As shown by operating experience, the owners of the cars with DSG and CVT are often applied to the services and these boxes are expensive to maintain. The classic slots on the market very long, and its design is continually refined and improved. Therefore, these boxes are characterized by high resource, robust and can be repaired in any service. Practice has shown that the resource transmission on the car is 300 to 400 thousand kilometers. This is a serious time, given that some modern engines go only 250. But to make this transmission last a long time, is to regularly change it, ATF fluid, namely every 60 thousand kilometers.


Article in other languages:

AR: https://tostpost.com/ar/cars/21147-the-device-and-principle-of-work-of-automatic-transmission-car.html

BE: https://tostpost.com/be/a-tamab-l/38693-prylada-pryncyp-pracy-akpp-a-tamab-lya.html

DE: https://tostpost.com/de/autos/38256-das-ger-t-und-das-prinzip-des-getriebes-des-fahrzeugs.html

ES: https://tostpost.com/es/coches/38033-el-dispositivo-y-el-principio-de-funcionamiento-de-la-transmisi-n-auto.html

HI: https://tostpost.com/hi/cars/22753-the-device-and-principle-of-work-of-automatic-transmission-car.html

JA: https://tostpost.com/ja/cars/20739-the-device-and-principle-of-work-of-automatic-transmission-car.html

KK: https://tostpost.com/kk/avtomobil-der/39099-rylymy-men-zh-mys-princip-avtomatty-ber-l-s-oraby-avtomobil-d.html

PL: https://tostpost.com/pl/samochody/40722-budowa-i-zasada-dzia-ania-skrzyni-samochodu.html

PT: https://tostpost.com/pt/carros/40392-o-dispositivo-e-o-princ-pio-de-funcionamento-de-uma-transmiss-o-autom-.html

TR: https://tostpost.com/tr/arabalar/35578-cihaz-ve-al-ma-prensibi-otomatik-anziman-araba.html

UK: https://tostpost.com/uk/avtomob-l/39509-pristr-y-princip-roboti-akpp-avtomob-lya.html

ZH: https://tostpost.com/zh/cars/25137-the-device-and-principle-of-work-of-automatic-transmission-car.html






Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."

Comments (0)

This article has no comment, be the first!

Add comment

Related News

"IZH 350 Planeta Sport" – frisky Soviet bike

it is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the li...

What is PPC

What is PPC

Many may be interested in the question of what is PPC? So, if to speak dry language, the transmission is designed to change a torque which is transmitted to the drive wheels from the crankshaft. And when viewed from the perspectiv...

The types of suspension vehicle, and device diagnostics

The types of suspension vehicle, and device diagnostics

What is the hub of the car is the most important? Almost all motorists will argue that, of course, the engine as it leads the car in motion. Others will say from the body of the transmission. But on the suspension of the car will ...

Parking rules

Parking rules

Very often, the motorist creates a situation where driving he learns easily, but Parking regulations are given to him hard enough. young drivers are sometimes hard to distinguish between such concepts as stopping the vehicle and i...

Headache of motorists - air leak

Headache of motorists - air leak

 to Buy a car – is one thing, but to take care of the equipment – it is quite another thing. Motorists plenty of headaches with the machine. Of course, if you – the owner of an expensive car, surely the prob...

Classification of oils

Classification of oils

 the Oil used for lubrication of the engine in the car. It is different kind. The choice of type depends on the engine and all of the conditions in which the vehicle is operated. Today, motor oils are divided into three groun...