Currently, despite the rapid development of technology, to create a completely sealed friction of the parts — the cylinder and the piston ring is not possible. Therefore, in the internal combustion engine over time during the operation of combustion products accumulate.
In the sump of crankcase gases pass through the piston rings, which are adjacent to the cylinders loose. The result is worse than the heat is removed, reducing the lifetime lubricating fluid and formed excessive pressure on all block seals. The crankcase ventilation system prevents excessive crankcase pressure.
At the beginning of the mechanism is as follows: from the case just output tube, producing gases into the atmosphere and polluting it. But the norms for emission of gases from vehicles was seriously tightened. Therefore, the crankcase ventilation system had to be developed by manufacturers.
In the form in which the system currently known, gases are not simply emitted into the atmosphere. They are sent to the motor by means of the derived tube from the crankcase, the other end of which is connected to the intake manifold. From there the gas is directed into the combustion chamber. At the time of the outbreak some of them burned and the other part is discharged through the exhaust mechanism. Only a small fraction of these gases back into the crankcase. So the process occurs without interruption.
There are two types of systems:
In the first case, as described in the beginning of the article, just gases are discharged into the atmosphere. In the second they are sucked into the intake pipeline. A closed crankcase ventilation system: VAZ and Lada, BMW and Mercedes, the Japanese and Americans is mainly used at present.
Recommended
"IZH 350 Planeta Sport" – frisky Soviet bike
It is believed that of the entire line of Soviet motorcycles "IZH" truly sporty just one. It is easy to guess that it was "IZH 350 Planeta Sport".History motorcycleIn 1973 the factory "Izhmash" was made a real breakthrough: the line went down the fir...
How does the rear bushing front arm and how many it serves?
The Rear bushing front arm – one of the constituent elements of the vehicle chassis. He refers to the guide elements of the suspension together with the levers endures tremendous stress with wheels. However, with this this item, there are many ...
Oil consumption in the engine. Six reasons
It is Hardly possible to find a motorist who would not be worried about the increased oil consumption. It is especially annoying when it happens with another new motor. Here are the most common causes that result in the consumption of oil in the engi...
In Addition, closed systems are available with variable or constant flow. The first type is more accurately able to adjust the recirculation sump. It varies depending on the number of incoming gases.
At the top is the oil separator of the crankcase ventilation system and inside it — an oil deflector. Its task is the release of gases from the oil particles. The oil separator of the crankcase ventilation system has the exit pipe. During normal operation, the motor in the crankcase should always occur a certain negative pressure. The valve can operate in three modes.
Let us briefly Consider all three of these options.
1. After the chock is formed in a low pressure from 500 to 700 mbar. The crankcase ventilation system, such a regime does not stand up. And the piston, under the action of vacuum closes the valve.
2. If the throttle is opened completely, the pressure there equal to atmospheric or even higher. Upon reaching the 500-700 mbar piston closes the valve for the passage of gases.
3. In the middle position, provided the normal pressure of the piston.
If valve operation is causing issues, its serviceability is easy to check. On idle on the neck, where filled with oil, placed a sheet of paper. If it is lowered and raised together with the diaphragm movement, the valve is serviceable.
The Normal functioning you can test another way. In the idle circulation, remove the vent hose and close it with your finger: it should feel suction.
If the motor operates at high speeds, the intake manifold pressure appears, which is of equal importance with atmospheric or greater. In this case, Carter gets more gas. If the inlet of a turbocharger, the vacuum will be too large and should be trimmed.
This provides a pressure-reducing valve that is triggered in the intake manifold when opening the damper. Mechanism consisting of a membrane and a spring is inserted in a plastic housing, which has inlet and outlet fittings.
Under normal vacuum pressure the spring is not loaded. When this membrane is raised and the gases are passed freely.
Under reduced pressure, the diaphragm descends and closes the exit, overcoming the action of the spring. The gases then move through a workaround — the canal orifice.
Unfortunately, acting positively on the one hand, the crankcase ventilation system engine creates a problem with other. Coming out of the pan, capture gases and particles grease, thus contaminating the intake system. In addition, they are deposited on the surfaces of the output channels and the details of the recirculating valve. This leads to a narrowing of the channels and may cause malfunction of the injection. If the diaphragm is jammed, the oil consumption will increase. Then you have to change the valve.
Also we must not forget about other important details and time to change the hose of the crankcase ventilation system — usually this is done together with recirculation valves. Inotherwise, it cracks and breaks.
To prevent expensive repairs, it is necessary to pay attention to specific spots on the seals of the engine, the increased consumption of fuel and lubricating fluid and unstable operation of the motor. If the time to drive to the service center, the problem will be solved in the Bud before she managed to inflict significant damage to the unit.
Article in other languages:
DE: https://tostpost.com/de/autos/23639-kurbelgeh-useentl-ftung-ger-t-arten-arbeitsweise.html
Alin Trodden - author of the article, editor
"Hi, I'm Alin Trodden. I write texts, read books, and look for impressions. And I'm not bad at telling you about it. I am always happy to participate in interesting projects."
Related News
New Renault Symbol. Owners reviews and car review
the long-Awaited second generation Renault Symbol got more vivid and interesting design, distinguishes this car from its somewhat clumsy predecessor. Smooth body lines and smooth trunk abolished have no talent, and awkwardness tha...
"Mitsubishi-Lancer": the owners of the 9th generation of cars
Japanese sedan “Mitsubishi-Lancer"-9 was first presented to the European public at the Moscow auto show in 2003. From the moment it was announced mass production of new items. 2 years later the Japanese slightly up...
Best scanners for vehicle diagnostics in Russian: list and reviews
the scan tool for vehicle diagnostics allow you to check almost all components of modern vehicles. Its use may be necessary not only in fire control indicators, but also in the preventive purposes. This approach allows to make tim...
Nissan Wingroad: all the fun of a Japanese passenger car
Nissan Wingroad – it is a utility vehicle produced in the light of the Japanese concern “Nissan”. It is produced for the domestic market. This model became very popular-in Japan and the far East. Why? There's a l...
Brake fluid DOT 4 - which is better? Specifications
Good brake fluid DOT 4 must meet certain requirements and conditions, the main of which is high boiling point. Failure to comply with the conditions fixed by the failure of a brake pedal, which can lead to negative consequences.th...
In auto parts stores often offer a wide range of oil filters, so car owners often face a dilemma of choice. Price, size, and appearance of their different. And although this is a small and cheap item in a big machine, without it t...
Comments (0)
This article has no comment, be the first!